IOGear GHSW8441 Manual de usuario
1
True 4K 4/8-Port Switcher with HDMI Connection
GHSW8441/GHSW8481
PART NO. M1529
User Manual
www.iogear.com
©2019 IOGEAR. All Rights Reserved. Part No. M1529, the IOGEAR logo is trademarks of IOGEAR. IOGEAR makes no warranty of
any kind with regards to the information presented in this document. All information furnished here is for informational purposes only
and is subject to change without notice. IOGEAR assumes no responsibility for any inaccuracies or errors that may appear in this
document.
3
Table of Contents
Package Contents 4
System Requirement 4
Introduction 5
Features 6
Overview 7
GHSW8441 7
GHSW8481 8
Hardware Installation 10
Rack mounting (GHSWS8481 only) 12
Operation 15
Cascading the GHSW8441 and GHSW8481 20
Safety Instructions 22
Specications 24
FAQ 26
Compliance Information 28
Limited Warranty 29
Contact 30
4
Package Contents
1 x GHSW8441 4-Port 4K HDMI Switch
Or
1 x GHSW8481 8-Port 4K HDMI Switch
1 x Power Adapter
1 x IR Remote Control Unit
1 x HDMI Cable
1 x User Manual
1 x IR Extender Cable (GHSW8481 only)
Note: Check to make sure that all the components are
present and that nothing was damaged in shipping. If
you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installa-
tion and operation procedures carefully to prevent
any damages to the unit, and/or any of the devices
connected to it.
Please visit IOGEAR website for any updates that may
become available in the future
1. No cables are included in this package. We strongly
recommend that you purchase high-quality cables of
the appropriate length since this will affect the quality
of the audio and video display.
2. If you wish to utilize the GHSW8441/GHSW8481’s
high-end serial controller function, you will need
to purchase an appropriate RS-232 cable. See
hardware installation number 5 for the RS-232
Controller, page 10.
System Requirement
• Up to 4/8 HDMI Source Devices
• 1 HDMI Display or Projector
5
Introduction
The IOGEAR 4/8-Port True 4K Switch with HDMI connection offers smooth, quick switching between four/eight
HDMI video sources such as a computer, Blu-ray, media player and cable or satellite receivers and a single
HDMI display. Send crystal clear, Cinema 4K video reaching true 4K resolutions to 4096 x 2160 @ 60Hz with
4:4:4 chroma subsampling, High Dynamic Range (HDR) and uncompressed audio/video for any variety of uses
including home theater, in lobbies and conference rooms and for digital signage.
Easily switch between each source automatically or manually. Utilize one of three switch modes and auto-cycle
through your sources with smooth video transitions to display a variety of content. Manually switch between
sources with the included IR remote control, program a universal remote via the RS-232 serial interface or select a
source via front panel push-buttons in settings where a remote control is not needed.
Enjoy clear, superior Cinema 4K video quality with true 4K resolutions to 4096 x 2160 @ 60Hz (4:4:4) and HDR
support to the display.
6
Features
• Connect and switch between 4/8 HDMI sources on 1 HDMI display
• Resolutions up to True 4K of 4096 x 2160 @ 60Hz (4:4:4)
• Distribute uncompressed audio and video formats
• Flexible control via push-button, IR remote & RS-232 serial control
• Bi-directional RS-232 support for universal remotes & touch panels
• Auto-switch mode detects & selects new HDMI port connections
• Supports high-speed data rates up to 18 Gbps
• No-slip locking power supply mechanism
• Cascade up to 3-levels
• HDMI 2.0 and HDCP 2.2 compliant
• CEC compliant
• Plug-n-Play
7
Overview
1
4
5 7
814
6
10 9
GHSW8441
11
12
13
8
21 3
4
5 6 7 8 9 10
11
12
13
GHSW8481
No. Component Description
1 Port selection Pushbutton Selects the corresponding HDMI input
2 Power Button Power button (GHSW8481 only) to enable/disable Standby mode and will NOT turn the
unit on or off. This is a lower power mode that will disable port selection button, port LEDs
and IR receiver.
3 Power LED Lights green to indicate the GHSW8481 in Standby mode (GHSW8481 only)
4 Port LED Port LED lights green indicating the selected port
5 Power jack Connects to the power adapter
6On/Off Auto Switch This switch enables/disables the next mode. In ON, the RS-232 is turned on. In OFF, the
switch will remain in next mode regardless of RS-232 commands
7 HDMI output port Connects to the HDMI IN port of the display device
8 HDMI input ports Connects to the HDMI Out port of the Source device(s)
9 IR Extension port Connects to an IR extender to extend the reception range for IR signals (not included)
10 RS-232 serial port Connects to a serial controller via a serial cable
11 Port Up/Port Down button Port Up will cycle to port forward (Port 1 to Port 2) Port Down will cycle to port backward
(Port 2 to Port 1)
12 On/Off button No function on the GHSW8441. For the GHSW8481 this will enable/disable HDMI output
13 Port Selection button This will select the port by port number
14 IR receiver Receives IR signals from an IR remote control unit (GHSW8441 only)
9
10
Hardware Installation
To install the switch, refer to the installation diagram as you perform the following steps:
1. Use an HDMI cable to connect the video display device to the HDMI output port on the rear of the GHSW8441/
GHSW8481.
2. Use HDMI cables to connect the video source devices to the HDMI input ports on the rear of the GHSW8441/
GHSW8481.
• If you are using the serial control function, use an appropriate RS-232 serial cable to connect the computer or
serial controller to the GHSW8441/GHSW8481’s female RS-232 port.
• Use a grounding wire to ground the unit by connecting one end of the wire to the grounding terminal and the
other end of the wire to a suitable ground.
• Note: Do not omit this step. Proper grounding helps to prevent damage to the unit from surges or static
electricity.
3. Plug the provided power adapter into an appropriate AC power source and plug the power adapter cable into the
power jack on the GHSW8441/GHSW8481.
4. Connect an IR extender (not supplied) to the external IR receiver input port (if you will be using this feature,
otherwise you can skip this step). This completes the basic installation of the 4/8 port 4K HDMI Switch. You may
now power on the display and source devices.
5. In order to use the RS-232 serial interface to attach to a controller (such as a PC) and the GHSW8441/
GHSW8481, use a serial modem cable. The end connecting to the GHSW8441/GHSW8481 should have a 9-pin
male connector (DB-9).
Note:Tocongurethecontrollerserialport,seepage15.
Otros manuales para GHSW8441
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cambiar de IOGear
IOGear
IOGear GHSW8241 Manual de usuario
IOGear
IOGear MiniView GCS632U Manual de usuario
IOGear
IOGear MiniView Extreme GCS1732 Manual de usuario
IOGear
IOGear MiniView GCS632U Manual de usuario
IOGear
IOGear MiniView GCS712U Manual de usuario
IOGear
IOGear GCS1412TAA4 Manual de usuario
IOGear
IOGear GCS932UB Manual de usuario
IOGear
IOGear MiniView GCS1742 Manual de usuario
IOGear
IOGear MiniView G-CS102U Manual de usuario
IOGear
IOGear Hybrid VGA KVM GCS742UW6 Manual de usuario
IOGear
IOGear M1672 Manual de usuario
IOGear
IOGear GCS1902 Manual de usuario
IOGear
IOGear GCS1792 Manual de usuario
IOGear
IOGear GCS1722 Manual de usuario
IOGear
IOGear GCS1932M Instrucciones de funcionamiento y mantenimiento
IOGear
IOGear GCS1932 Manual de usuario
IOGear
IOGear HUB-C+ Manual de usuario
IOGear
IOGear M1087-b Manual de usuario
IOGear
IOGear GUWIP204 Manual de usuario
IOGear
IOGear GCS1802 Manual de usuario
