IOGear GHSW8241 Manual de usuario
www.iogear.com
User Manual
4Kx2K 4-Port HD Switch
GHSW8241
PART NO. M1293
3
Table of Contents
Introduction 4
Package Contents 5
Requirements 5
Overview 6
Installation 7
Port Switching 8
Serial Port (RS-232) Conguration 9
Serial Port (RS-232) Conguration List 10
Powering Off and Restarting 16
Specication 17
Compliance Information 18
Limited Warranty 19
Contact 19
4
Introduction
IOGEAR’s 4Kx2K 4-Port HD Switch allows users to connect up to four HD
source devices to one HD display and supports Ultra HD 4Kx2K, the latest
digital format for high-denition displays at a distance of up to 50ft. For easy
access and convenience, this switch has one HD port on the front panel
that can be used to connect your portable devices, such as laptops, tablets
or digital cameras, while the other three HD ports on the back provide
permanent connections for your Blu-ray players, set-top boxes, game
consoles and more.
Switching between source devices can be done via the front panel push-
buttons, RS-232 bi-directional control or IR remote control with front panel
LEDs indicators for each source device. The built-in bi-directional RS-232
serial port allows you to control the switch through a high-end controller, PC
and / or home automation / home theater software system.
5
Package Contents
Requirements
1 x GHSW8241 4Kx2K 4-Port HD Switch
1 x HD Cable
1 x IR Remote Control
Source Devices
• HD output
Display
• HDTV or HD Projector with an HD input
Cables
• 4 HD Cables*
• RS-232 Cable (optional)*
• IR extension Cable (optional)*
*Cable not included
1 x Power Adapter
1 x Quick Start Guide
1 x Warranty Card
6
Overview
Front View
1. HD Input
2. Port Selection Push-button
Remote Control
1. Port Up / Port Down Buttons
2. Power ON / OFF
3. Port Selection Buttons
Back View
1. Power Jack
2. HD Output
3. HD Input
Power
IR EXT
HD OUTPUT HD INPUT HD INPUT HD INPUT
HD INPUT
Power
IR EXT
HD OUTPUT HD INPUT HD INPUT HD INPUT
HD INPUT
Power
IR EXT
HD OUTPUT HD INPUT HD INPUT HD INPUT
HD INPUT
3. Port Status LED
4. IR Receiver
4. RS-232 Serial Port
5. IR Extension Port
(IR extension cable not included)
4
1
1
1
3
2
2 4 5
2
3
3
7
Installation
Note: Make sure your source devices and display are powered off
before you start.
STEP 1
Connect an HD cable to the output port from the HD switch to the input port
of the HDTV or HD Projector.
STEP 2
Connect any HD media sources to the input ports of the HD switch via HD
cables.
STEP 3 (optional)
Connect your hardware or software RS-232 controller for HD switch control.
STEP 4 (optional)
If you have an IR extension cable (not included), plug it into the IR
Extension port and place it where the IR remote can reach it.
STEP 5
Connect the power adapter to the power jack and into an available wall
outlet.
PS4
IR EXT
HD OUTPUT HD INPUT HD INPUT HD INPUT
STEP 2
STEP 3
STEP 4
STEP 1
STEP 5
Control
processor
8
Port Switching
Via Front Panel Pushbutton
• Press the specic Port ID’s push-button to switch your media source.
Via IR Remote Control
• Press the specic port ID’s button to switch your media source.
• Press the Port Up / Down buttons to switch to the previous or next port
respectively.
*Note: The maximum range of the remote control is 20ft. Aim the remote
control at the IR receiver located on the front panel of the 4Kx2K 4-Port HD
Switch. For optimal performance, make sure there is a clear line-of-sight
between the remote control and the IR receiver.
Via RS-232 hardware or software device
• Please refer to the serial port conguration and command list on
pages 9-10 for more details.
9
Serial Port (RS-232) Conguration
Verication
After entering a command, using the instructions on pages 10-15, a
verication message will appear:
• Command OK – indicates that the command is correct and successfully
performed by the switch
• Command incorrect – indicates that the command has the wrong format
and / or values
The device’s built-in bi-directional RS-232 serial interface allows system
control through a high-end controller, PC and / or home automation / home
theater software package.
Conguring the Serial Port
The controller’s serial port should be congured as follows:
Description Setting
Baud Rate 19200
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
10
Switch Port Commands
The formulas for Switch Port commands are as follows:
1. Switch Command + Input Command + Port Number + [Enter]
- For example, to switch to input port 02, type the following:
sw i02 [Enter]
2. Switch Command + Enable / Disable HD Out + [Enter]
- For example, to disable the HD output signal, type the following:
sw off [Enter]
3. Switch Command + Port Sequence (+ / -) + [Enter]
- For example, to switch to the next input port (+), type the following:
sw + [Enter]
Note: Each command string can be separated with a [Space].
The following tables show the possible values and formats for the
Switch Port formulas:
Serial Port (RS-232) Conguration List
Command Description
sw Switch Command
Port Number Description
xx 01-04 (default is 01)
Control Description
on Enable HD Output Signal
off Disable HD Output Signal
+ Port Sequence – Next Port
- Port Sequence – Previous Port
Input Description
i Input Command
Tabla de contenidos
Otros manuales de Cambiar de IOGear
IOGear
IOGear GCS1802 Manual de usuario
IOGear
IOGear G-FH300 Manual de usuario
IOGear
IOGear GUS4C2 Manual de usuario
IOGear
IOGear GCS1792 Manual de usuario
IOGear
IOGear GCS182 Manual de usuario
IOGear
IOGear GCL1908 Manual de usuario
IOGear
IOGear MicroHub GUH274W1 Guía de configuración
IOGear
IOGear 8-Port DVI KVMP Switch Manual de usuario
IOGear
IOGear MiniView DVI-D KVM with audio and USB hub... Manual de usuario
IOGear
IOGear Gigalinq GUH3C34 Manual de usuario
IOGear
IOGear GCS1602CC Manual de usuario
IOGear
IOGear MiniView G-CS12 Manual de usuario
IOGear
IOGear GCS922U Manual de usuario
IOGear
IOGear MiniView III GCS1712 Manual de usuario
IOGear
IOGear GHSW8441 Manual de usuario
IOGear
IOGear GUB201 Manual de usuario
IOGear
IOGear MiniView Micro GCS62 Manual de usuario
IOGear
IOGear MiniView GCS1772 Manual de usuario
IOGear
IOGear GCS1902 Manual de usuario
IOGear
IOGear GVS881 GVS881 GVS881 Manual de usuario
