Intermec EasyCoder PD4 Manual de usuario

EasyCoder®PD4/PD41/PD42

Thermal Printhead (200/300 dpi) Installation Instructions

These instructions tell you how to install a 200 dpi or 300 dpi thermal

printhead in an EasyCoder PD4/PD41/PD42 printer. The kit contains the

following:

• 200 dpi or 300 dpi thermal printhead

• Printhead adapter printed circuit board (PCB)

Required Tools

To install the interface board in your printer, you need these tools:

• Screwdriver, slotted

• Screwdriver, Phillips (with magnetic tip)

Installing the Thermal Printhead and the Adapter PCB

Before you begin installation, please acknowledge the following important

safety notes:

Make sure the printer has been turned off and

disconnected from the power supply before you

start installation.

Stellen Sie sicher, dass der Drucker abgeschaltet

und von der Stromversorgung abgetrennt wurde,

bevor Sie mit der Installation beginnen.

Take precautions against electrostatic discharge, for

example, by wearing grounded wrist straps.

To install the thermal printhead

1Turn off the printer and unplug the power cord.

2Open the side door of the printer.

3Raise the printhead by pulling out the printhead lever and turning it

counterclockwise a quarter of a turn.

4Remove any thermal transfer ribbon.

5Remove the old printhead by pulling it out toward the front of the

printer.

Steps 6-9 describe how to replace the printhead adapter PCB which is

necessary if you are changing to a printhead with different resolution (for

instance, going from 200 dpi to 300 dpi). If this is not the case, go to

Step 11.

Note: If you are using a PD4 printer, you cannot switch to a

printhead with a different resolution other than that which the

printer was designed for.

6Move the balance boxes to the center position, to facilitate the removal of

the adapter PCB.

7Use an appropriate tool, for example a slotted screwdriver, to carefully

pry the printhead cable connector loose from the adapter PCB.

8Remove the two screws that attach the adapter PCB to the printer.

Remove the adapter PCB.

9Attach the new adapter PCB with the two screws removed in Step 8.

10 Connect the printhead cable to the adapter PCB.

11 Insert the new printhead and connect it to the adapter PCB.

12 Adjust the position of the balance boxes so that they fit the width of your

media.

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

©

2007 Intermec Technologies

Corporation. All rights reserved.

13 Close the side door of the printer.

14 Plug in the power cord and turn the printer on.

EasyCoder PD4/PD41/PD42 Thermal Printhead (200/300dpi) Installation Instructions

*1-960658-02*

P/N 1-960658-02

Otros manuales para EasyCoder PD4

5

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Accesorios de impresora de Intermec

Intermec

Intermec EasyCoder 501 E Manual de usuario

Intermec

Intermec PB50 Manual de usuario

Intermec

Intermec EasyCoder 3400d Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec PW50 Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec PC43d Manual de usuario

Intermec

Intermec 3240 Manual de usuario

Intermec

Intermec PB2 Series Manual

Intermec

Intermec 074788 Series Manual de usuario

Intermec

Intermec EasyCoder PF8 Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec PA30 Manual de usuario

Intermec

Intermec 825-192-001 Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec PB42 Manual

Intermec

Intermec PB42 Manual de usuario

Intermec

Intermec 3240 Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual