Intermec 3240 Manual de usuario

Centronics Parallel I/O Card

P/N 070872-001

Instruction Sheet

Intermec Technologies Corporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. service and technical support: 1.800.755.5505

U.S. media supplies ordering information: 1.800.227.9947

Canadian service and technical support: 1.800.688.7043

Canadian media supplies ordering information: 1.800.268.6936

Outside U.S. and Canada: Contact your local Intermec service supplier.

The information contained herein is proprietary and is provided solely for the purpose of allowing customers to

operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for any

other purpose without written permission of Intermec.

Information and specifications in this manual are subject to change without notice.

2000 by Intermec Technologies Corporation

The word Intermec, the Intermec logo, JANUS, IRL, Trakker Antares, Adara, EZBuilder, TE 2000, Data

Collection Browser, dcBrowser, Universal Access Point, UAP, Duratherm, EasyCoder, Precision Print,

PrintSet, Virtual Wedge, and CrossBar are either trademarks or registered trademarks of Intermec.

Throughout this manual, trademarked names may be used. Rather than put a trademark (or ) symbol in

every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and

to the benefit of the trademark owner, with no intention of infringement.

Centronics Parallel I/O Instruction Sheet

Centronics Parallel I/O Card Instruction Sheet

The following instructions explain how to install an Intermec Centronics Parallel I/O

Card into Intermec 3240, 3400, 3440, 3600, and 4400 printers. This procedure is to be

performed by trained Intermec service personnel only.

Parts Provided:

•Centronics Parallel I/O Card

•Ribbon cable

•(2) Phillips screws

Tools Required:

•Phillips screwdriver

Warning

Electrical equipment is dangerous! Make sure the printer power switch is turned off

and the AC power cord is disconnected before opening the tower door or removing the

electronics cover. Working on live equipment can cause injury or death.

Avertissement

“Le matériel électrique peut être dangereux ! Assurez-vous que l’interrupteur

d’alimentation de l’imprimante est éteint et que le cordon d’alimentation est

débranché, avant d’ouvrir le couvercle du support d’imprimante. Travailler sur du

matériel sous-tension peut provoquer des blessures ou la mort.”

Centronics Parallel I/O Card Instruction Sheet

Install the Parallel I/O Card in the 3xxx Printer

Caution

Static electricity can damage electronic components as you handle them. Static-

sensitive electronic components are packaged in static protective bags. Before

opening the bag, touch it to the metal base of the printer to reduce static electricity.

Touch the metal base of the printer to reduce static electricity before installing the

parallel I/O card in the printer.

1. Turn off the printer power and remove the power cord.

2. Remove the media cover and the electronics cover from the printer.

3. Remove and discard the optional I/O board port cover from the rear of the printer

(see illustration). Retain the two port cover screws.

3XXI005.eps

Optional I/O

board port

Retain the

two screws

Optional

I/O board

port cover

Centronics Parallel I/O Card Instruction Sheet

4. Connect one end of the ribbon cable to the parallel I/O card.

Note: Both ends of the ribbon cable are keyed. Either end can be plugged into the

parallel I/O card or the main PCB.

5. With the component side of the parallel I/O card facing the interior of the printer,

secure the parallel I/O card to the optional I/O board port with the two port cover

screws.

3XXXI008.eps

Parallel I/O

card

Optional I/O

board port

Main PCB

Ribbon

cable

Key

Ribbon

cable

Parallel I/O

card

Centronics Parallel I/O Card Instruction Sheet

6. Connect the free end of the ribbon cable to the appropriate connector (see the

following table) on the main PCB.

Printer Model Number I/O Connector

3240 J8

3400A and B J8

3400C and D J7

3440 J3

3600 J8

7. Reinstall and secure the media cover and electronics cover.

8. Reinstall the power cord.

9. Test that the printer recognizes the parallel I/O card by printing a hardware

configuration test label. See the printer user’s manual for instructions on printing a

hardware configuration test label. The following message should appear on the

configuration test label:

I/O Option Card: Centronix

Centronics Parallel I/O Card Instruction Sheet

Install the Parallel I/O Card in the 4400 Printer

Caution

Static electricity can damage electronic components as you handle them. Static-

sensitive electronic components are packaged in static protective bags. Before

opening the bag, touch it to the metal base of the printer to reduce static electricity.

Touch the metal base of the printer to reduce static electricity before installing the

parallel I/O card in the printer.

1. Turn off the printer power and remove the power cord.

2. Open the tower door by removing the three Phillips screws at the rear of the printer

(see illustration).

3. Remove and discard the port cover from the optional I/O board port. Retain the two

screws.

Tower door

Phillips screw

(3 places)

Optional I/O

board port

Port

cover

Phillips

screws

3XXXI001.eps

AC power

cord

Centronics Parallel I/O Card Instruction Sheet

4. Secure the parallel I/O card (Part No. 052713) to the optional I/O board port with

two Phillips screws. The components on the parallel I/O card must face toward the

interior of the printer.

5. Connect one end of the ribbon cable to the parallel I/O card.

Note: Both ends of the ribbon cable are keyed. Either end can be plugged into the

parallel I/O card or the main PCB.

6. Plug the parallel I/O cable (Part No. 053924) into J18 on the main PCB. Check that

all the cable connections (not shown) on the main PCB are secure.

7. Before closing the tower door, check all cable connections. All cables must be

carefully folded prior to securing the electronics door. Ensure that the keypad cable

is folded away from the encoder wheels of the TTR assembly. Close the tower door

and secure it with three Phillips screws.

8. Test that the printer recognizes the parallel I/O card by printing a hardware

configuration test label. For help, see the 4400 User's Manual (Part No. 058607).

The following message should appear on the configuration test label:

I/O Option Card: Centronix

Main PCB

J18

Parallel I/O card

Phillips screws

(2 places)

Tower door

Parallel I/O cable

Optional I/O

board port

3XXXI002.eps

Otros manuales para 3240

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de impresora de Intermec

Intermec

Intermec EasyCoder 501XP Manual de usuario

Intermec

Intermec EasyCoder 4420 Manual

Intermec

Intermec EasyCoder PF4i Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Intermec

Intermec PB50 Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec 3240 Manual de usuario

Intermec

Intermec PW50 Manual de usuario

Intermec

Intermec 074788 Series Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec PB42 Manual

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec PB2 Series Manual

Intermec

Intermec EasyCoder PD41 Manual de usuario

Intermec

Intermec 825-192-001 Manual de usuario

Intermec

Intermec EasyCoder PF4ci Manual de usuario

Intermec

Intermec PB42 Manual de usuario

Intermec

Intermec 4630 Manual de usuario

Intermec

Intermec CN3 Series Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec EasyCoder 3400d Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual