ICP DAS USA TM-P3R3 Manual de usuario

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-P3R3

3-channel Isolated Digital Input and 3-

channel Relay Output Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_p3r3.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-P3R3 provides 3 channels for digital input and 3 channels for relay output, each

of which features photocouple isolation. All output channels are form A type relays,

while input is based on sink- or souce-type using a wire connecion. All input channels

can be used an 16-bit counters. There are options for configuring power-on and safe

digital output values. 4 kV ESD protection and 3750 VDC intra-module isolation are also

provided.

2. Terminal Assignment

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

•Use 26-12 AWG wire for signal

connections.

•Strip the wire to a length of

7±0.5mm.

•Use a crimp terminal for wiring.

•Avoid high-voltage cables and

power equipment as much as

possible.

•For RS-485 communication, use

insulated and twisted pair 24 AWG

wire, e.g. Belden 9841.

4. Default Settings

Default settings for the tM-P3R3 module are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-P3R3 3-channel DI and 3-channel Relay Output Module- QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA I-7014D Manual de usuario

ICP DAS USA

ICP DAS USA SG-3227 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Manual de usuario

ICP DAS USA

ICP DAS USA ET-7015 Manual de usuario

ICP DAS USA

ICP DAS USA tSH-725 Manual de usuario

ICP DAS USA

ICP DAS USA SP-S2-DS Manual de usuario

ICP DAS USA

ICP DAS USA M-7033D Manual de usuario

ICP DAS USA

ICP DAS USA tM-TH8 Manual de usuario

ICP DAS USA

ICP DAS USA M-7019Z Manual de usuario

ICP DAS USA

ICP DAS USA M-7041 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2061 Manual de usuario

ICP DAS USA

ICP DAS USA WISE-5801-MTCP Manual de usuario

ICP DAS USA

ICP DAS USA ET-7200 Series Manual de usuario

ICP DAS USA

ICP DAS USA MDC-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2016N Manual de usuario

ICP DAS USA

ICP DAS USA iDaSer-9000 Manual de usuario

ICP DAS USA

ICP DAS USA I-7088 Manual de usuario

ICP DAS USA

ICP DAS USA I-7083 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD8C Manual de usuario

ICP DAS USA

ICP DAS USA ET-7H16M Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7024 Manual de usuario

ICP DAS USA

ICP DAS USA ET-7083 Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 21 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-87004W Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

ICP DAS USA tM-P3R3 Manual de usuario

Manuales populares de Unidad de control de otras marcas