ICP DAS USA TM-AD8C Manual de usuario

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-AD8C

8-channel Isolated Current Analog Input

Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_ad8c.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-AD8C is an current input module that includes 8 single-ended analog input

channels and provides a programmable input range on all analog inputs (0 ~ 20 mA, 4 ~

20 mA). The sampling rate of the tM-AD8C is adjustable and is available in either fast or

normal mode and It also provides 4 KV ESD protection as well as 2500 Vrms intra-

module isolation.

2. Terminal Assignment

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

Use 26-12 AWG wire for signal connections.

Strip the wire to a length of 7±0.5mm.

Use a crimp terminal for wiring.

Avoid high-voltage cables and power equipment as much as possible.

For RS-485 communication, use insulated and twisted pair 24 AWG wire, e.g.

Belden 9841.

4. Default Settings

Default settings for the tM AD modules are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。Analog Input Type: type code 08, -10V to 10V

。Baud Rate: 9600 bps

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the analog current input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA tET Series Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2026 Manual de usuario

ICP DAS USA

ICP DAS USA M-7051D Manual de usuario

ICP DAS USA

ICP DAS USA PET-7261 Manual de usuario

ICP DAS USA

ICP DAS USA M-7069 Manual de usuario

ICP DAS USA

ICP DAS USA ISN-101 Manual de usuario

ICP DAS USA

ICP DAS USA tSG-3781B Manual de usuario

ICP DAS USA

ICP DAS USA I-7052D Manual de usuario

ICP DAS USA

ICP DAS USA tM-TH8 Manual de usuario

ICP DAS USA

ICP DAS USA GTP-230 Manual de usuario

ICP DAS USA

ICP DAS USA iDaSer-9000 Manual de usuario

ICP DAS USA

ICP DAS USA SG-3784M Manual de usuario

ICP DAS USA

ICP DAS USA tZT-P4C4 Manual de usuario

ICP DAS USA

ICP DAS USA ET-87P2 Manual de usuario

ICP DAS USA

ICP DAS USA I-8014W Manual de usuario

ICP DAS USA

ICP DAS USA ET-6000 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-8092F Manual de lista de piezas

ICP DAS USA

ICP DAS USA GPS-721-MRTU Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Manual de usuario

ICP DAS USA

ICP DAS USA M-7028 Manual de usuario

ICP DAS USA

ICP DAS USA I-7016D Manual de usuario

ICP DAS USA

ICP DAS USA I-8123W Guía de configuración

ICP DAS USA

ICP DAS USA ECAT-2051 Manual de usuario

ICP DAS USA

ICP DAS USA M-7060 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

ICP DAS USA tM-AD8C Manual de usuario

Manuales populares de Unidad de control de otras marcas