ICP DAS USA M-7060 Manual de usuario



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7060

4-channel Digital Input and 4-channel Relay

Output Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7060_m_7060d

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The 7060 series provides 4 digital input channels, 2 Form A and 2 Form C signal relay output

channels, while the M-7060P provides 4 digital input channels, 2 Form A and 2 Form C power

relay output channels. All digital input channels can be used as 16-bit counters. In addition, the

digital input channels can be selected either as sink- or source-type via wire connections. The

“D” versions of the 7060 series provide eight LED indicators that can be used to monitor the

status of the digital input and relay output. The “M” versions of the 7060 series support both the

Modbus RTU and DCON protocols, which can be configured via software. There are also

options for configuring power-on and safe values. 4 kV ESD protection and 3750 VDC intra-

module isolation are also provided to enhance noise protection capabilities in industrial

environments. The 7060 series is the ideal solution for small signal switching applications, while

the M-7060P is the perfect solution for high power applications.

2.TerminalAssignment



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3.Block/WiringDiagram



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

。 Module Address: 01

。 DIO Type: Type 40

。 Baud Rate: 9600 bps

。 Checksum disabled

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70604‐channelDIand4‐channelRelayOutputDAQModule

‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA ZT-257 Series Manual de usuario

ICP DAS USA

ICP DAS USA GT-540P-3GWA-OEM1 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2012H Manual de usuario

ICP DAS USA

ICP DAS USA tSH-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA WP-5231 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Manual de usuario

ICP DAS USA

ICP DAS USA I-7045D Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 21 Series Instrucciones generales

ICP DAS USA

ICP DAS USA tPET-P2R2 Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2510 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7060D Manual de usuario

ICP DAS USA

ICP DAS USA M-7067D Manual de usuario

ICP DAS USA

ICP DAS USA GW-7552-M Manual de usuario

ICP DAS USA

ICP DAS USA ET-7065 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD5 Manual de usuario

ICP DAS USA

ICP DAS USA tDS-700-T Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7016 Manual de usuario

ICP DAS USA

ICP DAS USA ET-7H16M Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2051 Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD8C Manual de usuario

ICP DAS USA

ICP DAS USA PDS-5000 Series Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 4 Series Instrucciones generales

ICP DAS USA

ICP DAS USA I-8124W Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario