HP D7171A - NetServer - LPr Manual de usuario

HP NetServer LXr 8500

PCI Hot Plug Utility

User Guide

Printed in August 1999

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including, but

not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this

material. Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright. All rights

are reserved. No part of this document may be photocopied, reproduced, or translated to

another language without the prior written consent of Hewlett-Packard Company.

The use of trademarks or other designations is for reference purposes only. The following

trademarks are used in this manual:

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft and MS-DOS

are U.S. registered trademarks of Microsoft Corp. Windows and Windows NT are

trademarks of Microsoft Corp. Novell, NetWare, and IntranetWare are registered

trademarks of Novell, Inc.

Hewlett-Packard Company

Network Server Division

Technical Communications / MS 45SLE

10955 Tantau Avenue

Cupertino, CA 95014-0770, USA

iii

Contents

1 PCI Hot Plug Utility for Windows NT ............................................................. 1

Opening the Hot Plug Utility .............................................................................. 1

Opening the PCI Hot Plug Utility ....................................................................... 2

Powering Down a PCI Slot ................................................................................ 5

Removing a Hot Plug Board .............................................................................. 8

Powering Up a PCI Slot ................................................................................... 12

2 PCI Hot Plug Utility for Novell NetWare....................................................... 17

Overview.......................................................................................................... 17

NetWare 5 Requirements............................................................................ 19

Novell Configuration Manager Console ...................................................... 20

Slot Options Menu....................................................................................... 22

Slot Detailed Information Screen................................................................. 24

Opening the User Interface ............................................................................. 25

Powering Down a PCI Slot .............................................................................. 26

Removing a Hot Plug Board ............................................................................ 32

Replacing a Hot Plug Board ............................................................................ 36

Powering Up a PCI Slot ................................................................................... 39

1 PCI Hot Plug Utility for Windows NT

Opening the Hot Plug Utility

Use this topic only for Microsoft's Windows NT 4.0 on the HP NetServer LXr

8500 using the software utility to perform PCI Hot Plug Replacement (or Online

Replacement) operations. This topic and its subsequent topics describe how to

turn power Off and On to the PCI slots (P1-P10) using the PCI Hot Plug Utility.

For Novell's NetWare 5 NOS, go to the topics under Chapter 2 "Hot Plug

Replacement (NetWare)".

CAUTION To prevent a system crash or hang, never remove a PCI board

from a slot with power on. Always use the Hot Plug Utility to

turn power off to the Hot Plug slot before performing any

replacements.

The PCI board is only Hot Plug-capable if it has a hot plug compliant driver

available and installed on the HP NetServer. If the PCI board is not Hot Plug-

capable, remove and replace the board with the HP NetServer's power turned off.

Microsoft’s Windows NT 4.0 does not, by itself, support hot plug replacement,

but HP Configuration Assistant on the HP Navigator CD-ROM, installs the PCI

Hot Plug Utility on the NT server, along with the system software and the drivers

for some of the HP supported PCI Hot Plug boards. Through this Utility,

Windows NT 4.0 does support hot replacement of identical boards. The PCI Hot

Plug Utility is also found in the diskette library on the Navigator CD-ROM. If

using manual installation, follow the installation instructions found in the

readme.txt file to install the Utility on the NT NetServer.

The Hot Plug Utility is used to replace the PCI Hot Plug board in a four-step

process:

1. Turning power off to the PCI slot

2. Removing the PCI board

3. Replacing the PCI board

4. Turning power on to the PCI slot

The Hot Plug Utility is used to turn power off to the PCI slot before removing the

PCI board, and then after replacing the PCI board, it is used to turn power back on

Chapter 1 Server Administration Using HP TopTools

to the PCI slot. Refer to the Help File for a description of the PCI Hot Plug

Utility's buttons and functions.

NOTE The Power Button is the only button required to do basic Hot

Plug Replacement.

Opening the PCI Hot Plug Utility

Use this procedure to open the PCI Hot Plug Utility in Windows NT 4.0.

NOTE If the left P (Power) LED is lit (green) in the PCI Hot Plug

Utility, the corresponding Power LED on the rear panel will be

green. This is also true for the right A (Attention) LED; that is,

if the right A (Attention) LED is lit (red) in the PCI Hot Plug

Utility, the corresponding Attention LED on the rear panel will

be amber.

1. In Windows NT 4.0, click on the Start button and then select the

Programs menu.

2. From the Programs menu, select PCI Hot Plug and then select the PCI Hot

Plug Utility.

A display similar to the example shown in Figure 1 appears.

This example has 9 slots filled with PCI boards. Slot 1 shows no board

installed and slot 2 has no hot plug compliant driver. Slots 2 to 6 and 9 to

10 all have power applied to the slot, shown by the P (Power) LED turned

on, (left P LEDs are green with Normal in status field) and are operating

normally. Slot 7 has a left P LED on (green), but also has a fault condition

indicated by the right A (Attention) LED (red), with its status field

displaying Link Fault, suggesting a corrective action. Slot 8 has a green P

LED, but has *Mixed – multiple device board (represents a multifunction

adapter) in the status field. See Help file for more information about

functions and buttons.

Chapter 1 PCI Hot Plug Utility for Microsoft Windows NT

Figure 1. PCI Hot Plug Utility

3. If no hot plug support appears under Board in the Utility's window

instead of the desired PCI board, one of the following conditions might be

true:

àThe PCI Hot Plug board is not supported by a hot plug compliant

software driver.

àThe software driver for the PCI Hot Plug board is not properly installed

and loaded.

See Windows NT Help for how to load drivers.

àThe PCI board may not use a driver, or the driver is defective.

NOTE If you have a board without a hot plug compliant driver in one

of the hot plug slots, the board will show up in the Utility as no

hot plug support, and the Utility will not allow you to power

down the slot.

4. Identify the physical location of the desired PCI Hot Plug board, using the

PCI Hot Plug Utility and Figures 2 and 3.

Chapter 1 Server Administration Using HP TopTools

PCI Hot Plug

LED Indicators

(Amber)

Power

ttention

P10 P9 P8 P7 P6 P5 P4 P3 P2 P1

Figure 2. PCI Slot Locations (Rear view)

Battery

IDE (CD-ROM)

Flexible Disk

Drive

SCSI A

SCSI B

I/O Riser

Slot

PCI LED

Display

Cable

(J1F1)

Remote Contro

Board Cable

Auxiliary I C

P10-P9

+3.3 VDC

66/33 MHz

P8-P7

+3.3 VDC

66/33 MHz

P6-P3

+5 VDC

33 MHz

P2-P1

+5 VDC

33 MHz

Remote Control

Board must be

in slot P2.

10 9 87654321

Configuration

Switch Block

Bus 0

Bus 1

Bus 2

Bus 3

Figure 3. PCI Slot Locations (I/O Baseboard top view)

Chapter 1 PCI Hot Plug Utility for Microsoft Windows NT

Powering Down a PCI Slot

Use this topic to select and power down a PCI slot on the I/O baseboard.

1. Select the desired PCI slot (slot P7) to replace by pointing to it with the

mouse cursor. See Figure 4.

This example has a red A (Attention) LED fault condition associated with

it.

2. Left click on the desired slot (slot P7) with the mouse.

Figure 4. Selecting PCI Slot to Turn Power Off

CAUTION Opening a PCI hold-down latch with power applied to the slot

may result in a system crash or hang. Always use the Utility to

first power off the slot. Turning off power to any slot will stop

all input (I/O) or services associated with the board while

power is turned off to the slot.

3. Click on the Power button in the upper right of the screen. See Figure 1.

A pop-up prompt appears requesting conformation of this action.

See Figure 5.

Chapter 1 Server Administration Using HP TopTools

NOTE The Power button is the only button required to do basic Hot

Plug Replacement operations.

Figure 5. Pop-up Menu

4. Confirm your selection by clicking on Yes.

As soon as confirmation is complete, the left P (Power) LED in the Utility

window turns off (gray) and the slot status changes from "Link Fault" (or

Normal)to Not Ready. The corresponding Power LED (green) for the PCI

slot on the rear panel will also turn off. This means power to this slot is

turned off. See Figure 6.

CAUTION If the rear panel Power LED for the desired PCI slot does not

turn off, do not attempt to remove the PCI Hot Plug board.

Return to Step 1 in this procedure to ensure you have selected

the correct slot to power down.

NOTE If you have a PCI board with a non-compliant drive in the

desired PCI slot, the PCI board will show up on the Utility’s

Otros manuales para D7171A - NetServer - LPr

117

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Software de HP

HP StorageWorks 4/8 - SAN Switch Manual de instrucciones

HP ProLiant Lights Out-100 Manual de usuario

HP MultiSeat ms6000 Manual de usuario

HP HPE XP P9500 Manual de instrucciones

HP T5725 - Compaq Thin Client Manual de usuario

HP b2600 Manual de instrucciones

HP StorageWorks 2/32 - SAN Switch Manual de instrucciones

HP Surestore Disk Array 12h - And FC60 Manual de referencia

HP StorageWorks MSA 2/8 - SAN Switch Manual de usuario

HP Integrity rx1620 Manual de usuario

HP 500 G2 Manual de usuario

HP Pro 3130 MT Manual de usuario

HP BladeSystem Dual NC370i - Multifunction Network... Manual de usuario

HP Data Protector A.06.11 Guía de configuración rápida

HP ProLiant BL280c G6 Manual de referencia

HP ProLiant StorageWorks NAS 2000s Manual de usuario

HP Guardian Manual de usuario

HP 8000 - Elite Convertible Minitower PC Manual de usuario

HP Compaq NW8000 Manual de usuario

HP Integrity BL860c Manual de programación

HP Rx2620-2 - Integrity - 0 MB RAM Manual de usuario

HP Configuring Arrays Manual de usuario

HP Pavilion xg900 - Desktop PC Instrucciones de instalación y funcionamiento

HP T5145 - Thin Client - Tower Manual de servicio

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario

Novell

Novell SP2 - S Manual de instrucciones