HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Manual de instrucciones

HP StorageWorks Simple SAN

Connection Manager 2.10 release notes

Part number: 5697-0060

Sixth edition: June 2009

Legal and notice information

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212,

Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S.

Government under vendor's standard commercial license.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the

express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional

warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Java is a US trademark of Sun Microsystems, Inc.

Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.

Red Hat and Enterprise Linux are registered trademarks of Red Hat, Inc., in the United States and other countries.

Description

The HP StorageWorks Simple SAN Connection Manager (SSCM) is a GUI-based management

application for basic management of storage area network (SAN) components, such as host bus

adapters (HBAs), switches, and storage arrays. The SSCM uses Microsoft's Virtual Disk Service (VDS)

to manage storage arrays. SSCM provides simplified storage management for VDS-compliant storage

devices in a single, integrated, wizard-based user interface.

Products and devices supported

SSCM supports the following products and devices:

•HP StorageWorks 8/20q Fibre Channel Switch

•HP StorageWorks EVA4x00/6x00/8x00 with XCS 6.110 or later

•HP StorageWorks EVA4400

•HP StorageWorks MSA1x00 with V7.00 or later firmware

•HP StorageWorks MSA2000fc/HP StorageWorks MSA2000fc G2

Operating system support

SSCM supports the Microsoft Windows Server 2003 R2 operating system with Service Pack 2.

Supported client operating systems include the following:

•Microsoft Windows Server 2003 with SP2

•Microsoft Windows Server 2008

•SUSE Linux Enterprise Server (SLES) 9 and 10

•Red Hat Enterprise Linux (RHEL) 4 and 5

•VMware ESX 3.5

•HP-UX 11.23, 11.31

Prerequisites

This section describes requirements for using SSCM.

System requirements

Ensure that the server running your management software (management station) meets the following

minimum requirements (for supporting SSCM and other HP software):

•Microsoft Windows Server 2003 R2 with Service Pack 2

•512 MB of memory

•200 MB of disk space

•One 2.0-GHz processor

•One CD-ROM drive, one Ethernet port

HP StorageWorks Simple SAN Connection Manager 2.10 release notes 3

•One or more PCI-e slots for the HP StorageWorks 81Q PCI-e Fibre Channel HBA (or other supported

QLogic FC HBAs)

•Java Runtime Environment (JRE) 1.5 or later

•Internet browser: Microsoft Internet Explorer (IE), Netscape Navigator, or Mozilla Firefox

Installation instructions

For detailed installation instructions, see the HP StorageWorks Simple SAN Connection Manager

user guide, available on the HP website http://www.hp.com/go/8Gb-SSC.

Important information

This section provides information about installation, Enterprise Virtual Array (EVA), Modular Smart

Array (MSA), the switch, and other issues relating to SSCM.

Installation issues

•MSA2000fc G2 support: SSCM 2.10 does not include the software required to directly support

MSA2000fc G2.

Workaround: To add support for the MSA2000fc G2 to SSCM 2.10, you must install the HP

StorageWorks MSA2000 Software Bundle V1.26 or later on the SSCM management station and

all nonmanagement stations that will use the MSA2000fc G2. HP StorageWorks MSA2000

Software Bundles V1.26 for all supported operating systems are available for download from the

HP MSA2000 website: http://h18006.www1.hp.com/storage/disk_storage/msa_diskarrays/

san_arrays/msa2000fc/index.html.

Under Support, click MSA2000fc G2, and then under Tasks for HP StorageWorks 2000fc G2

Modualr Smart Array, click Download drivers and software.

HP recommends that you install SSCM first, and then install the HP StorageWorks MSA2000

Software Bundle V1.26. When installing the MS2000 software bundle on the management station,

be sure to select the optional MSA2000 VDS provider.

If the MSA2000 software was installed previously, you can install SSCM; however, you must take

the following precautions:

• Ensure that version 1.26 of the HP StorageWorks MSA2000 Software Bundle is installed. If

an earlier version of MSA software is installed, update to V1.26. For a list of the minimum

required versions of MSA2000 components, see Minimum MSA2000 software component

versions.

• Verify that the optional MSA2000 VDS provider is installed on the management station. If not,

re-install the MSA2000 software bundle and select the optional MSA2000 VDS provider.

• During installation of SSCM, select No when prompted to install older software on your system.

(Expect to see several of these prompts.)

• The SSCM installer will attempt and fail to install an older version of the MSA2000 SES driver.

You can ignore the resulting error.

Minimum MSA2000 software component versions When the installation is complete, verify

that the following versions of MSA2000 software are installed:

• MSA2000 SES Driver 2.5.0 (Build 21) (Windows 2003 only)

• MSA2000 MPIO DSM 2.5.1 (Build 29)

• MSA2000 CAPI Proxy 2.5.0 (Build 22) (SSCM management station only)

• MSA2000 VDS Provider 2.5.1 (Build 5) (SSCM management station only)

•Network installations: The SSCM installer does not support installation over a direct network share

using \\<ip or system-name>\share. Attempting to install SSCM in this manner results in

the following error message:

Internal Error This installation wizard has experienced an error. Please

contact your software vendor with the error code below. Error: File

copy failed. Error Code (23).

Workaround: Install SSCM from a local CD, a local disk, or a network share that is mapped to a

drive letter.

•Updating from SSCM 1.00: When upgrading from SSCM 1.00 to SSCM 2.10, the following error

message appears and the installation halts:

An xpath query failed. Please view the error log for specifics about

the error. Error Code: 16777377

Workaround: To resolve this issue:

1. Delete all files in one of the following directories (depending on the architecture [x64/x86]

of the operating system):

•C:\Program Files (x86)\Hewlett-Packard\InstallWizard\HP Storage-

Works Simple SAN Connection Manager

•C:\Program Files\Hewlett-Packard\InstallWizard\HP StorageWorks

Simple SAN Connection Manager

2. Insert the SSCM 2.10 CD and start the installation.

•Linux install issue on RHEL 5: Under specific distributions, such as Red Hat Enterprise Linux 5, the

installation CD is automounted using the following CD label:

# /media/HpInstallx.x/

If this occurs, the CD may be mounted with the no execution flag, causing the installation script

to fail. Installation failure may be indicated by the following error message:

# ./install_smb.sh

bash: ./install_smb.sh: /bin/sh: bad interpreter: Permission denied

Workaround: Manually unmount the installation CD. For example, if the CD was automounted in

/media/HpInstallx.x, issue the following commands to remount the CD:

# unmount /media/HpInstallx.x

# mkdir —p /mnt/cdrom

# mount /dev/cdrom /mnt/cdrom

If the unmount command fails with a busy warning, make sure you have closed all applications

and consoles that could be using the CD media.

•On Microsoft Windows Server 2008, the MSA2000 uses the native Microsoft MPIO. Use the

following procedure for all Windows 2008 systems in your SAN to configure MPIO.

To activate MPIO:

1. Select Start > Settings > Control Panel.

2. Double-click the MPIO icon.

3. Select the second tab, Discover Multi-Paths.

4. The MSA2000 appears in the Others section in the Device Hardware ID.

5. The MSA2000 should appear as HP LOGICAL VOLUME. Select this entry, and then click

Add.

HP StorageWorks Simple SAN Connection Manager 2.10 release notes 5

•Windows Server 2008 upgrade issue: Performing an upgrade from a previous installation on the

Windows Server 2008 will cause MSA2000 MPIO and SES drivers to fail to install.

Workaround: These components are not required by the Windows Server 2008. You can ignore

the failure of those components during an upgrade from a previous version.

EVA-specific issues

•EVA configuration: The SSCM has the following restrictions when managing an EVA array:

• Host definitions cannot be removed from the EVA by the SSCM.

• After a port (HBA) has been added to a host definition, the port cannot be removed by the

SSCM.

• HP Command View EVA offers great flexibility in how you can configure an EVA. However,

the SSCM may not operate as expected if an array was configured using HP Command View

EVA. You can use SSCM or HP Command View EVA to configure an array, but not both.

NOTE:

Using HP Command View EVA to delete unwanted entries in an array's configuration (such as a

host or port that has been physically removed) is supported.

•EVA login account: If the EVA login user name is changed, use the HP VDS Configuration Utility

for EVA to re-enter the new user name and password. This utility is installed with the EVA VDS

hardware provider and can be launched from Start > Programs > Hewlett-Packard > Hardware

Providers.

•EVA4400 not discovered on startup: The EVA4400 is not discovered upon startup of SSCM.

Workaround: If your SAN contains an EVA4400, ensure that all HP Command View EVA

installations in the SAN are running HP Command View EVA 8.0 or later.

MSA1x00-specific issues

•MSA LUN name between Array Configuration Utility (ACU) and SSCM does not match: LUN names

created by the MSA ACU and the SSCM do not match when displayed. The ACU LUN name is

partly shown in SSCM as LUN identification.

•MSA hardware provider memory leak: The HP MSA hardware provider installed with the HP

StorageWorks SSCM has a memory leak that may increase over time when VDS operations are

exercised. To reclaim lost memory, close SSCM to unload the MSA hardware provider. See the

HP website for updates to the HP MSA hardware provider.

•Hosts connecting to MSA storage subsystems may not be discovered by SSCM during fabric changes:

When MSA responds to a fabric event, such as zoning changes, the HBA agent software takes

some time to discover the MSA storage subsystem. When the system is in this state, and SSCM is

launched, it may not discover the host because its HBA agent software is still busy.

Workaround: If this occurs, either relaunch SSCM after a few minutes or refresh the server list,

and/or manually add the server.

Switch issues

•SSCM and switch passwords: If the switch password is set up or updated using SSCM, SSCM

remembers the password and will not prompt for one whenever a switch operation is initiated.

However, if you set up or change the password in another application (such as QuickTools), SSCM

cannot retrieve the switch information when launched. SSCM shows the default generic switch

name, and any switch operation that you request will prompt for the password.

•SSCM shows switch zoning information as Unknown for vendor and device type: The SSCM uses

the switch zoning component Fibre Channel worldwide port name (WWPN) to match the vendor

and device type. If the switch zoning is not WWPN based, it shows the information as Unknown

in the Switch Zoning Information dialog box.

Other issues

•The graphics for the MSA and EVA are not accurate: The storage subsystem graphics in the Manage

Storage Subsystem dialog box are intended as an abstract representation of the MSA and EVA

storage subsystems and their enclosures and drives. The graphic images do not actually reflect

the physical layout of the subsystems.

•LUN multipath information: A LUN's multipath information is available only if that LUN is presented

to the management host where the VDS hardware provider and SSCM are installed and running.

Workaround: To obtain multipath information for LUNs presented to other hosts, issue the hpdsm

devices command from either the EVA DSM command line interface (CLI) or the MSA DSM CLI

on that host.

To launch the EVA DSM, select Start > Programs > Hewlett-Packard > EVA DSM > HPDSM CLI.

To launch the MSA DSM, select Start > Programs > Hewlett-Packard > MSA DSM > HPDSM CLI.

•SSCM startup: SSCM may take several minutes to start up. The size of your SAN and the

configuration of your storage directly affects the startup time.

SSCM uses an Ethernet broadcast mechanism to discover the hosts and their HBAs in the SAN. If

there are a large number of hosts in the network responding to this broadcast, the host discovery

process may take some time to complete.

•SSCM fails to start: If you install SSCM with the MSA only option, and HP Command View EVA

is installed, SSCM will be unable to start. The error RegOpenKeyEx failed with error 2:

The system cannot find the file specified is displayed when you attempt to start

SSCM.

Workaround: To correct this problem, reinstall SSCM and select the EVA only or the EVA and

MSA option if an array is present in the configuration. If no EVA is present, uninstall the HP

Command View EVA suite.

•IA64 BIOS update: The HBA driver update feature for Windows on IA64 is not supported in SSCM.

•Format drive message: During partition creation and formatting for LUNs for Windows Server

2008, a Windows Format Drive message is displayed to confirm formatting or cancel.

Workaround: None. This message will not impact the function, but a new confirmation window

appears for each new partition. Click Cancel to close the window.

•Server name changes: If the name or other attribute of a server being managed by SSCM is

changed independent of SSCM, SSCM continues to display the original name, even after restarting.

The server change is not detected until a Server Refresh is done because SSCM matches up

the HBA WWN with the saved server data. This saved data is not updated until a new broadcast

or FDMI refresh is done. A server refresh is not performed on application startup or asynchronously

while the application is open.

Workaround: To see the new server name, use the Refresh the Server List option.

HP StorageWorks Simple SAN Connection Manager 2.10 release notes 7

•Creating partitions on the management station: Deleting LUNs presented to the management station

may cause errors if new LUNs are created right after the old LUNs are deleted. The new LUNs

may not be initialized and a drive letter not assigned.

Workaround: Reboot the management station after deleting any LUNs that were presented to the

management station. Then, perform the template deployment or creation of any new LUNs.

•Default zoning with null name error: If you create default zoning in SSCM with a null name

and apply the changes, an error message states Create default zone error: Zone set

creation failed and the current zones on the switch in QuickTools are deleted.

Workaround: When setting the default zoning, you must specify a zone name, otherwise, applying

the new default zoning will fail and will subsequently delete any previously existing zones.

Otros manuales para 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard...

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Software de HP

HP 2230s - Compaq Business Notebook Manual de instrucciones

HP Tc4100 - Server - 256 MB RAM Guía de inicio rápido

HP VL400 - Vectra - 64 MB RAM Manual de servicio

HP Compaq dc7900 Business PC Manual de usuario

HP Integrity rx2800 - i2 Manual de usuario

HP AJ878A - StorageWorks 320 GB Hard Drive Manual de instrucciones

HP Neoware e140 - Thin Client Manual de usuario

HP ProLiant DL320e Manual de usuario

HP Rx2620-2 - Integrity - 0 MB RAM Manual de usuario

HP NC373m - PCI Express Dual Port Multifunction Gigabit Server... Manual de usuario

HP 1032 Manual de usuario

HP B6960-96035 Manual de usuario

HP 345646-001 - StorageWorks NAS 2000s External Storage... Instrucciones de instalación y funcionamiento

HP Rx2620-2 - Integrity - 0 MB RAM Manual de usuario

HP SN6000B Manual de instrucciones

HP NonStop SQL/MX Manual de usuario

HP LASERJET PRO 400 Manual de servicio

HP Integrity rx1600 Guía de referencia rápida

HP Kayak XU700 Manual de usuario

HP StorageWorks XP10000 - Disk Array Manual de instrucciones

HP 742n - Pavilion - 512 MB RAM Guía de referencia rápida

HP A4500A - VMEbus Single Board Computer 744... Manual de instrucciones

HP C7791C - DesignJet 130 Color Inkjet Printer Guía de configuración

HP T5145 - Thin Client - Tower Manual de servicio

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario

Novell

Novell SP2 - S Manual de instrucciones