HP Model 744 - VME Workstation Manual de usuario

Installing the A4980A

EISA-to-PCI Backplane Upgrade

This upgrade is to be performed only by HP

qualiﬁed service personnel.

HP Part No. A4980-90601

Edition E0698

Printed in U.S.A.

2

Hewlett-Packard Co. 1998

Printing History

First Printing: June 1998

UNIX is a registered trademark in the United States and other countries,

licensed exclusively through X/Open Company Limited.

NOTICE

The information contained in this document is subject to change without

notice.

HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-

ble for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copy-

right. All rights reserved. No part of this document may be photocopied,

reproduced or translated to another language without the prior written con-

sent of Hewlett-Packard Company.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-

ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS

252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA

94304.

10 9 8 7 6 5 4 3 2 1

3

Kit Contents

Kit Contents

Make sure that you have kit A4980A and that it contains the following

items:

• PCI backplane

• GSC-to-PCI interface board

Tools Required

You’ll need the following items to install the PCI Module:

• #1 Pozidriv screwdriver (with extension)

• T10 and T-15 Torx screwdrivers

• Static-free work area.

Prerequisites

1Stop any application programs, then shut down the system.

2Turn the system off, and unplug the power cord(s) and all other cables and

terminators from the system.

3If the system is mounted in a rack, remove it from the rack.

WARNING: To avoid electrical shock, make sure you unplug the power cable from the wall

outlet and the system unit before proceeding any further.

4

Prerequisites

CAUTION: The internal components of the system are susceptible to

mechanical and electrostatic shock. To prevent such damage from

occurring, observe the following precautions during the installation

procedure.

• Stand on a static-free mat

• Wear a static-grounding wrist strap to ensure that any accumulated

electrostatic charge discharges from your body to ground. Attach the

static-grounding wrist strap by following the instructions on the pack-

age that contains the strap. Be sure to attach one end of the strap to the

system chassis.

• Handle system and upgrade kit components carefully to prevent dam-

age from mechanical shock.

5

Installation

Installation

1Remove the system top cover (see Figure 1).

Figure 1 Removing the Top Cover

Screws Screws

Screws

6

Installation

2Remove the front bezel (see Figure 2).

Figure 2 Removing the Front Bezel

7

Installation

3Remove the two screws from the rear of the system, and slide the mid-tray

toward the front, and then up, out of the system (see Figure 3).

Figure 3 Removing the Mid-Tray

8

Installation

4Remove any installed EISA cards.

5Remove the EISA backplane/interface assembly (see Figure 4).

Figure 4 Removing the EISA Backplane Assembly

9

Installation

6Assemble the PCI backplane/interface assembly (see Figure 5).

Figure 5 Assembling the PCI Backplane Components

10

Installation

7Install the PCI backplane assembly into the chassis (see Figure 6).

Figure 6 Installing the PCI Backplane Assembly

NOTE: The PCI backplane only supports option cards with +5 volt bus signalling.

Otros manuales para Model 744 - VME Workstation

8

Este manual sirve para los siguientes modelos

4

Tabla de contenidos

Otros manuales de Hardware de computadora de HP

HP

HP 273914-B21 - Smart Array 6404/256 RAID... Manual de usuario

HP

HP MicroServe Manual de usuario

HP

HP 3000 Series Manual

HP

HP Adaptive Rack Cooling System Guía del usuario

HP

HP 8886 - Photosmart Camera Dock Digital Docking... Manual de usuario

HP

HP HPE SimpliVity 325 Manual de usuario

HP

HP 624189-B21 Manual de usuario

HP

HP 82718A Manual de usuario

HP

HP 64782 Manual de usuario

HP

HP Integrity rx1600 Manual de usuario

HP

HP Xw4600 - Workstation - 2 GB RAM Manual de usuario

HP

HP Compaq t5500 Manual de usuario

HP

HP D7171A - NetServer - LPr Manual de usuario

HP

HP 98640A Manual de instalación y funcionamiento

HP

HP E5000 Manual de usuario

HP

HP HPE LSWM2XGT2PM Manual de usuario

HP

HP F768WM Manual de usuario

HP

HP GbE2c - Blc Layer 2/3 Fiber SFP Option Cómo utilizar

HP

HP D7171A - NetServer - LPr Manual de usuario

HP

HP QMH2672 Manual de usuario

HP

HP 98625A Manual de usuario

HP

HP QUERY Manual de usuario

HP

HP 64793 Series Manual de usuario

HP

HP StoreOnce 2700 Manual del operador

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario