HP D7171A - NetServer - LPr Manual de usuario

HP NetServer

Ultra Hot Swap Hard Disk Drive

and Tray

HP Part Number 5969-5925

Printed in February 2000

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Novell NetWare®is a registered trademark of Novell, Inc.

Microsoft®Windows NT, NTAS®, and MS-DOS®are registered trademarks of

Microsoft Corporation.

SCO®UNIX®is a registered trademark of The Santa Cruz Operation, Inc.

Banyan®and VINES®are the registered trademarks of Banyan Systems

Incorporated.

OS/2®is the registered trademark of the International Business Machines

Corporation.

Hewlett-Packard Company

Network Server Division

Technical Communications/MS 45SLE

10955 Tantau Avenue

Cupertino, CA 95014-8059 USA

Audience Assumptions

The guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

1 Installation Procedure................................................................................. 1

Installing the Hot Swap Hard Disk Drive in a Tray (optional).......................... 1

Unpacking and Shipping................................................................................ 2

Installing the Hot Swap Hard Disk Drive ........................................................ 3

Removing the Hot Swap Hard Disk Drive ...................................................... 4

2 Disk Drive Characteristics........................................................................... 7

NetWare and DOS ........................................................................................ 7

OS/2 and Windows NT.................................................................................. 8

UNIX and Banyan Vines................................................................................ 9

3 Application Alerts...................................................................................... 11

D4903A Cooling Requirements.................................................................... 11

D3604A/B Storage System/6 using Ultra SCSI Drives................................. 11

Hot Swap Drives Must be Parked Prior to Removal..................................... 11

A Warranty and Support............................................................................... 13

Hardware Warranty ..................................................................................... 13

HP Repair and Telephone Support .............................................................. 13

HP World Wide Web Site............................................................................ 13

B Regulatory Information............................................................................. 15

1 Installation Procedure

This guide describes how to attach an Ultra hot swap hard disk drive to a hot

swap tray and install the hard disk drive in your computer. Additionally, this

guide provides the cautions and instructions for removing and storing the hard

disk drive.

Installing the Hot Swap Hard Disk Drive in a Tray

(optional)

If you purchase a hot swap tray accessory (D3349B) separately from the hot swap

hard disk drive, follow these steps to attach the tray accessory:

1. Make sure that the hot swap hard disk drive meets the specifications

written on the hot swap tray label. If the hot swap drive is capable of

running Ultra2 at LVD (low voltage differential) signal levels, a jumper

must be installed on the drive to force the drive into SE (single-ended)

mode. Refer to the drive manual for the location of a “Force SE” jumper.

NOTE Not all Ultra2/LVD drives have this jumper. If the drive does

not have the Force SE jumper, that drive model will probably

not work with HP NetServer Ultra Hot Swap backplanes.

2. Attach the drive to the hot swap tray with the screws provided in the order

shown in Figure 1-1.

Chapter 1 Installation Procedure

Figure 1-1. Hot Swap Hard Disk Drive and Tray Installation

Unpacking and Shipping

Your system has a shipping plug to ensure that the hot swap hard disk drive is

not damaged while it is being transported. Save this plug. If you plan to transport

your system, reinstall your shipping plug as shown in Figure 1-2.

Chapter 1 Installation Procedure

Figure 1-2. Shipping Plug

Installing the Hot Swap Hard Disk Drive

CAUTION Use one of the six (6) vertical shelves in the system. Do not

attempt to install the hot swap hard disk drive in the

horizontal shelves.

Protect the hot swap hard disk drive from static electricity by

leaving it in its antistatic bag until you are ready to install it.

Before handling the hard disk drive, touch any unpainted

metal surface to discharge static electricity. When you remove

the hard disk drive from the antistatic bag, handle it only by

the frame.

Do not touch the electrical components. Place the hard disk

drive on the antistatic bag whenever you set it down.

1. If there is a filler panel in the disk shelf, remove that panel.

2. On the hot swap hard disk drive, press the locking tab down, and lift the

lever up as far as it can go. (See Figure 1-3.) Lifting the lever retracts the

locking pin at the top of the hard disk drive.

Chapter 1 Installation Procedure

3. Holding the hard disk drive as shown in Figure 1-3, slide the hot swap

hard disk drive slowly into the shelf until it stops.

4. Press the lever down as far as it will go.

Figure 1-3. Installing the Hot Swap Hard Disk Drive

Removing the Hot Swap Hard Disk Drive

1. To unlock the hot swap hard disk drive, push the tab down and then lift

the front lever.

2. Pull the hard disk drive out about an inch (2.5 cm) to break the power

connection.

3. Wait about 30 seconds for the hard disk drive to stop spinning and the

drive heads to park.

4. Use your hand to support the bottom of the hard disk drive, as shown in

Figure 1-4. Slowly pull the hard disk drive straight out. Do not allow the

hard disk drive to fall.

5. Turn the hard disk drive slowly to its horizontal storage orientation.

6. Place the hard disk drive in an electrostatic protected container. Do not

stack hot swap hard disk drives.

Chapter 1 Installation Procedure

Figure 1-4. Removing the Hot Swap Hard Disk Drive

Otros manuales para D7171A - NetServer - LPr

117

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de HP

HP A1250 Series Instrucciones de montaje

HP MicroServe Manual de usuario

HP Xw4400 - Workstation - 2 GB RAM Manual de usuario

HP CB001A Manual de usuario

HP P Class 450/500/550/600/650/700/750 Manual

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario

HP 3000 Series Manual

HP D7171A - NetServer - LPr Manual de instalación y operación

HP A5830AF-48G Manual de usuario

HP JG587A Manual de usuario

HP Visualize c100 Manual de usuario

HP AF079A Guía de instalación

HP A58 0AF Series Instrucciones de montaje

HP Z400 - Workstation Manual de usuario

HP Smart Array 5300A Manual de usuario

HP 8168E Manual de usuario

HP Pavilion xl700 - Desktop PC Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP HPE SimpliVity 325 Manual de usuario

HP D7171A - NetServer - LPr Manual de usuario

HP Xw460c - ProLiant - Blade Workstation Manual de usuario

HP ProLiant DL140 Manual de usuario

HP WL110 - Wireless PC Card Manual de usuario

HP Apollo r2800 Instrucciones de instalación

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario