Kontron DIMM-PC/MD Manual de usuario

DIMM-PC/MD

Product Manual

Document Revision 1.0

DIMM-PC/MD Product Manual Content

Kontron® Embedded Modules GmbH iRevision 1.0

CONTENTS

1. USER INFORMATION...................................................................................................1

1.1 ............................................................................................. ABOUT THIS MANUAL 1

1.2 .......................................................................................................... TRADEMARKS 1

1.3 ................................................................................................................. GENERAL 1

1.4 ..............................................................................................................WARRANTY 2

1.5 ...............................................................................................TECHNICAL SUPPORT 3

2. INTRODUCTION ............................................................................................................4

2.1 ..............................................................................KONTRON DIMM-PC-CONCEPT 4

3. FEATURES OF THE DIMM-PC/MODEM..................................................................6

4. BLOCK DIAGRAMM DIMM-PC/MODEM ................................................................7

5. MECHANICAL SPECIFICATION ...............................................................................8

5.1 ....................................................................................ELECTRICAL SPECIFICATION 11

5.2 ................................................................................PERFORMANCE SPECIFICATION 12

5.3 .......................................................................... ENVIRONMENTAL SPECIFICATIONS 13

6. HARDWARE-INSTALLATION ..................................................................................14

6.1 ...................................................................................................LINE-CONNECTION 14

6.2 ................DEFINITION OF THE HARDWARE-INTERRUPTS AND OF THE I/O-ADDRESS 15

7. SOFTWARE SPECIFICATION...................................................................................16

7.1 ........................................................................................................DIMM-PC/MD 16

7.2 ....................................................................AT COMMANDS REFERENCE MANUAL 17

8. TROUBLESHOOTING.................................................................................................25

9. REVISION HISTORY...................................................................................................25

DIMM-PC/MD Product Manual User Information

Kontron® Embedded Modules GmbH 1Revision 1.0

1. USER INFORMATION

1.1 About This Manual

In this document Kontron Embedded Modules GmbH will also be referred to by the short

form "Kontron".

The information in this document has been carefully reviewed and is believed to be

accurate and reliable. However, no responsibility is taken for inaccuracies. Furthermore,

Kontron reserves the right to make changes to any part of this manual to improve

reliability, function or design. Kontron does not assume liability for any product or circuit

described.

1.2 Trademarks

AT and IBM are trademarks of International Business Machines

XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines

Corporation.

Microsoft is a registered trademark of Microsoft Corporation.

Intel is a registered trademark of Intel Corporation.

All other products and trademarks mentioned in this manual are trademarks of their

respective owners.

The reproduction, transmission or use of this document or its contents is not permitted

without expressed written authority.

Violators will be liable for damages. All rights created by patent grant or registration of a

utility model or design, are reserved.

Kontron 1996Standards

1.3 General

For the circuits, descriptions and tables indicated no responsibility is taken as far as

patents or other rights of third parties are concerned.

The information in the technical descriptions describes the type of the boards and shall

not be considered as assured characteristics.

DIMM-PC/MD Product Manual User Information

Kontron® Embedded Modules GmbH 2Revision 1.0

The reproduction, transmission or use of this document or its contents is not permitted

without expressed written authority. Violators will be liable for damages. All rights,

including rights created by patent grant or registration of a utility model or design, are

reserved.

1.4 Warranty

Each board is carefully and thoroughly tested before being shipped. If, however,

problems should occur during the operation, please check your user specific settings of

all boards included in your system. That is often the source of the error. If a board is

defect, it can be sent to your supplier for repair. Please take care of the following steps:

1. The board returned should correspond to the factory default settings since a test is

only possible under these settings.

2. Upon receipt of the board, please be aware that your user specific settings were

changed during the test.

Within the guarantee, the repair is free as long as the guarantee conditions were held. If

no error has been found, you will be charged with the test costs due to the high test

expenditure. Repairs outside of duration of the guarantee will be charged.

This Kontron product is warranted against defects in material and workmanship for our

guaranteed warranty period from the date of shipment. During the warranty period,

Kontron will, at its option, either repair or replace products which prove to be defect.

For warranty service or repair, the product must be returned to a service facility

designated by Kontron.

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance or handling by buyer, unauthorized modification or misuse, operation

outside of the environmental specifications for the product, or improper installation or

maintenance.

Kontron will not be responsible for any defects or damages due to a faulty Kontron

product other than the products supplied by Kontron

DIMM-PC/MD Product Manual User Information

Kontron® Embedded Modules GmbH 3Revision 1.0

1.5 Technical Support

Technicians and engineers from Kontron and/or its subsidiaries are available for

technical support. We are committed to making our product easy to use and will help you

use our products in your systems.

Before contacting Kontron technical support, please consult our Web site for the latest

product documentation, utilities, and drivers. If the information does not help to solve the

problem, contact us by email or telephone. The table below lists Kontron technical

support contacts and service facilities.

Asia Europe North/South America

Kontron®Embedded Modules Asia Ltd.

Kontron Embedded Modules

GmbH Kontron

5F-1, 341, Sec 4

Chung Hsiao E. Road

Taipei, Taiwan

Brunnwiesenstr. 16

94469 Deggendorf

Germany

3988 Trust Way

Hayward, CA 94545

USA

Tel: +886 2 2751 7192 Tel: +49 (0) 991-37024-0 Tel: 510-732-6900

Fax: +886 2 2772 0314 Fax: +49 (0) 991-37024-104 Fax: 510-732-7655

[email protected] [email protected]

DIMM-PC/MD Product Manual Introduction

Kontron® Embedded Modules GmbH 4Revision 1.0

2. INTRODUCTION

2.1 Kontron DIMM-PC-Concept

It is likely that anyone who deals with micro-controller-development, has already thought

of the application of PC-architecture and considered the PC as the engine for an

application. However, most design engineers will get back to the old 87C51 or a similarly

more or less efficient micro-controller. The reasons why the Embedded PC was not yet

able to push away the micro-controllers from the printed boards, are many.

Embedded PCs are mechanically larger than a solution with a micro-controller.

The hardware of an Embedded PC is much more expensive than the micro-controller

solution.

The power consumption of an Embedded PC is usually higher than the one of a micro-

controller circuit.

A lot of times PCs have to be used with ribbon cables which are a possible cause of error.

Micro-controllers are available with a large number of peripheral functions, the PC,

however only has a standard periphery.

On the other hand there are some serious disadvantages of micro-controller solutions.

The software-development is much more complicated and expensive than under a

standard operating system.

Connection to standard-interfaces such as LANs and modems requires complicated driver

software.

Graphical user interfaces can be realized only by large programming efforts.

The development tools are by far not as powerful as PC-programming systems.

Micro-controllers do by far not have as many different PC-SW development tools

available.

This is why the purchase price is usually considerably higher for micro-controller

development tools.

Ready-made software solutions for standard tasks are only available in a very limited

extent.

The specified reasons are only a few of the more common ones, which are important in

deciding whether to implement a micro-controller or to change to PC-architecture.

DIMM-PC/MD Product Manual Introduction

Kontron® Embedded Modules GmbH 5Revision 1.0

It is a matter of fact, that these points are not always estimated objectively. Who knows

for sure at the beginning of a project how much programming efforts will have to be

made for realizing the application? In most cases, this can only be rated afterwards which

means, too late. Also the problematic nature/software care within the course of the

product life-span is often ignored.

If the Embedded PC is to be implemented in today's micro-controller applications, the

advantages of the PC-architecture have to prevail, compared to a micro-controller

solution.

With the DIMM-PC, JUMPtec has aimed at the micro-controller market and has

presented a completely new concept for the Embedded PC-solution.

The DIMM-PC solves the problems of size and cabling. The prices have been drastically

reduced thanks to new technical designs, making the solution of using a DIMM-PC

possible for many applications. The driving of peripheral functions was also made easier

by the expansion towards the ISA-bus-standard.

DIMM-PC/MD Product Manual Features of the DIMM-PC/Modem

Kontron® Embedded Modules GmbH 6Revision 1.0

3. FEATURES OF THE DIMM-PC/MODEM

The DIMM-PC/Modem incorporates following features:

•?Low power CMOS technology.

•?5V only power supply.

•Signal pinning according DIMM-PC specification

•Different selectable I/O-Addresses and IRQs

•?Board size : Modem-module 68 x 40 mm (2,68" x 1,57")

DAA-module 30 x 50 mm (1,18” x 1,97”)

•support for:

V.21, V.22(1200bps), V.22bis(2400bps),V.23, Bell 103, Bell 212, V.32, V.32bis,

V.34, V.34+, K56flex, V.90, V.92, V.17, V.29, V.27ter and V.21 channel 2

DIMM-PC/MD Product Manual Block Diagramm DIMM-PC/Modem

Kontron® Embedded Modules GmbH 7Revision 1.0

4. BLOCK DIAGRAMM DIMM-PC/MODEM

The modem may be connected directly to the ISA BUS signals of the DIMM-PC.

DAA Module DIMM-PC/

MODEM DIMM-PC

DIMM-PC BUS

(ISA-BUS)

I/O

PSTN

DIMM-PC/MD Product Manual Mechanical Specification

Kontron® Embedded Modules GmbH 8Revision 1.0

5. MECHANICAL SPECIFICATION

Pinout of DIMM-PC/Modem

Pin number

Signal

Pin number

Signal

SA0

GND

OSC

BATT

SA1

VCC

SA2

RI4#

MASTER#

DCD4#

SA3

DTR4#

BALE

DSR4#

SD15

RTS4#

SA4

CTS4#

TXD4 / DO

SD14

RXD4 / DI

SA5

RI3#

DACK#2

DCD3#

SD13

DTR3#

SA6

DSR3#

IRQ3

RTS3#

DRQ7

CTS3#

DACk#7

TXD3

IRQ4

RXD3

SA7

SD12

IRQ5

TXD+

SA8

TXD-

SD11

RXD+

IRQ6

RXD-

SA9

LNLED

SD10

LKLED

IRQ7

GND

SA10

MD14

SD9

MD13

KEY

SYSCLK

MD12

SA11

SD8

REF#

BLUE

SA12

GREEN

I2DAT

RED

SA13

VCC

I2CLK

VSYNC

SA14

GND

DRQ0

HSYNC

SA15

FPBACK

DACK#0

MODUL

IRQ14

SA16

IOR#

GND

SA17

FPVDD

IRQ15

BLANK#

IOW#

P17

SA18

P16

IRQ12

P15

SMEMr#

100

P14

101

SA19

102

P13

103

IRQ11

104

P12

105

SMEMW#

106

P11

107

AEN

108

P10

109

IRQ10

110

111

IOCHRDY

112

113

SBHE#

114

115

SD0

116

117

IOCS16#

118

GND

119

ZWS#

120

121

SD1

122

123

MEMCS16#

124

125

SD2

126

127

SD3

128

129

DRQ2

130

131

SD4

132

VPANEL

133

SD5

134

FPVEE

135

IRQ9

136

VDCLK

137

SD6

138

LLCLK

139

SD7

140

VCC

141

RSTDRV#

142

LFS

Pinout of the western socket on the Modem-Module

57551 3 5

top side

14314113965636159

KEY

Tabla de contenidos

Otros manuales de Hardware de computadora de Kontron

Kontron

Kontron CP6002 Manual de usuario

Kontron

Kontron aFLAT Series Manual de usuario

Kontron

Kontron COMe-mSP1 Manual de usuario

Kontron

Kontron KBox E-200 Series Manual de usuario

Kontron

Kontron coolMonster/PM Manual de usuario

Kontron

Kontron ePanel-mgx Manual de usuario

Kontron

Kontron MPC-pONE Manual de usuario

Kontron

Kontron SMARC-sAMX8X Manual de usuario

Kontron

Kontron COM Express Eval 10 Manual de usuario

Kontron

Kontron Kiss-Stor 0/5 Manual de usuario

Kontron

Kontron AM4500 Manual de usuario

Kontron

Kontron KBox C-102 Series Manual de usuario

Kontron

Kontron CP-RIO6-923 Manual de usuario

Kontron

Kontron KTGM45/mITX Manual de usuario

Kontron

Kontron CP-ADAP-P47-PB (3U) Manual de usuario

Kontron

Kontron CP3002 Manual de usuario

Kontron

Kontron COMh-caRP Manual de usuario

Kontron

Kontron AM4024 Manual de usuario

Kontron

Kontron CP308 Manual de usuario

Kontron

Kontron coolMonster/PM Manual de usuario

Kontron

Kontron ePanel-C3 Manual de usuario

Kontron

Kontron CP6005-SA Manual de usuario

Kontron

Kontron SL iMX6UL Manual de usuario

Kontron

Kontron BL Pi-Tron CM3+ Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario

Jupiter

Jupiter RAM PACK Manual de usuario