Hand Held Products 4800p Manual de usuario

4800p

Quick Start Guide

Note: Refer to your user’s guide for information

about cleaning your device.

Getting Started

Turn off computer’s power before connecting the

scanner, then power up the computer once the

scanner is fully connected.

USB Connection

Reading Techniques

The 4800p scans bar codes and also captures

images. It can be used with or without a stand.

The 4800p’s

viewfinder projects

a green aiming

beam that should

be centered over

the bar code, but

can be positioned

in any direction for

a good read.

Hold the scanner

with the aiming beam centered over the bar code.

The 4800p beeps when it successfully reads a bar

code. Do not move the 4800p over another bar

code until it beeps. The optimum distance between

the 4800p and the object being scanned is 2 to 5

inches (5.1 - 12.7 cm). The height from the 4800p to

the stand’s tray is the proper distance.

The aiming beam is smaller when the scanner is

closer to the code and larger when it is farther from

the code. Hold the scanner close to smaller bar

codes, and farther away from large bar codes to get

a proper read.

If the bar code is highly reflective (e.g., laminated),

you may need to tilt the scanner at an angle so the

bar code can be scanned.

4800p Stand

The stand holds the 4800p at a fixed distance for

capturing images or reading bar codes on security/

identification cards. The wedge insert supplied with

the stand provides the optimum angle for scanning

and capturing images in most lighting conditions.

The card should be placed on the wedge with the

bar code closest to the back of the stand.

Standard Product Defaults

The following bar code resets all standard product

default settings.

Standard Product Defaults

Interface

Scan the bar code that describes the PC or

interface you are using.

USB Keyboard (PC)

Emulate External Keyboard

USB Japanese Keyboard (PC)

USB COM Port Emulation

USB HID Bar Code Imager

Keyboard Country

Scan the Program Keyboard Country bar code

below, then scan the numeric bar code(s) from

page 9, then the Save bar code to program the

keyboard for your country. As a general rule, the

following characters are not supported by the

scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~.

Note: For a complete list of country codes, see the

User’s Guide for your product at our website,

www.handheld.com.

Country Code Scan Country Code Scan

Belgium 1 Italy 5

Denmark 8 Norway 9

Finland 2 Spain 10

France 3 Switzerland 6

Germany/Austria 4 USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

Reread Delay

This sets the time period before the scanner can

read the

same

bar code a second time. Setting a

reread delay protects against accidental rereads of

the same bar code.

Suffix

If you want a carriage return after the bar code,

scan the Add CR Suffix bar code. To add a tab

after the bar code, scan the Add Tab Suffix bar

code. Otherwise, scan the Remove Suffix bar

code to remove the suffixes.

Medium Reread Delay

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a

Code ID prefix to all symbologies at once.

Note: For a complete list of Code IDs, see the

User’s Guide for your product at our website,

www.handheld.com.

Function Code Transmit

When this selection is enabled and function codes

are contained within the scanned data, the imager

transmits the function code to the terminal. Charts

of these function codes are provided in your User’s

Guide. When the imager is in USB keyboard mode,

the scan code is converted to a key code before it is

transmitted.

Add Code ID Prefix To All Symbologies

(Temporary)

Enable

(Default)

Disable

Data Format Editor Instructions

The following are abbreviated instructions for

entering a data format. For complete instructions

refer to your User’s Guide, available at our website,

www.handheld.com.

1. Scan the Enter Data Format symbol.

2. Primary/Alternate Format: scan 0for Primary

Format.

3. Terminal Type: scan 99 for any terminal type.

4. Code I.D.: scan 99 for any bar code type.

5. Length: scan 9999 for any length bar code.

6. Editor commands: use the Programming Chart

that follows.

7. Scan Save to save your entries.

Enter Data Format

Clear All Data Formats

Save

Programming Chart

Otros manuales para 4800p

Tabla de contenidos

Otros manuales de Lector de código de barras de Hand Held Products

Hand Held Products

Hand Held Products QUICK CHECK 890 Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 4400 Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manual de usuario

Hand Held Products

Hand Held Products Quick Check PC600 Manual de usuario

Hand Held Products

Hand Held Products 2020 Guía del usuario

Hand Held Products

Hand Held Products IT4000 Manual de uso y cuidado

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products 2020 Manual de usuario

Hand Held Products

Hand Held Products 4X00 Guía de inicio rápido

Hand Held Products

Hand Held Products IMAGETEAM 3800E Manual de usuario

Hand Held Products

Hand Held Products QUICK CHECK 890 Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 3900 Manual de usuario

Hand Held Products

Hand Held Products QUICK CHECK 890 Manual de usuario

Hand Held Products

Hand Held Products 4230 Manual de usuario

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products Scanteam 5700 Manual de usuario

Hand Held Products

Hand Held Products 4600g Manual de usuario

Hand Held Products

Hand Held Products HANDHELD 3800G Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 3800i Instrucciones de instalación y funcionamiento

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manual de usuario

Hand Held Products

Hand Held Products 4800p Manual de usuario

Hand Held Products

Hand Held Products 2020 Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 3800i Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario