Geeetech Acrylic I3 Pro Instrucciones de operación
Assemble Instruction of GeeetechAcrylic Prusa I3
Pro & pro B
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
Notice:
1. This kit contains tiny parts; please keep them away from kids under 3.
2. This building instruction applies to both Geeetech Acrylic Prusa I3 pro and pro B.
3. Some pictures of the printed part may be a bit different from those in your
package, no worries, they work the same, and the way to assemble is similar.
4. Building and operating 3D printer involves electricity, so all necessary precautions
should be taken and adhered to.
5. Building a 3d printer requires a certain amount of handling ability and basic
knowledge of working principle of 3D printer.
6. Be patient, please. If you have any problems assembling, please contact us, we
will try our best to help you.
1Unfold the box and check the package
Unfold the package and take all the parts out to check the condition of the items. As
you can see, all the parts are packed very carefully.
ShenzhenGETECHCO.
,
LTD
GEEETECH
All the acrylic plate has been etched with part ID and the plate is covered with
a sheet of kraft paper, you need to tear them off.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
Tips:
1. Before assembly, you are advised to put all the parts, especially the screws and nuts
in order, which will save you a lot of time looking for the required parts.
2. The part ID is corresponding to the number labeled on the bag of every part. Some
parts may not have label, you can refer to the pictures on the package list.
2 Assemble Y axis
2.1 Assemble the rods of a Y axis
Step1. Assemble the 2 threaded rods.
Part IDRequired numberRequired parts
NO.52M10 threaded rod
NO.A142Y plate connecting
plate
NO.186M8 spring washer
NO.98M10 washer
NO.128M10 nut
Thread the nuts and washers into the two M10 threaded rods separately. The order
should be:
1) Thread the acrylic fender (Y plate connecting plate) in the middle.
2) Thread the M10 washer > M8 spring washer >M10 nut > M10 nut > M10 washer
on the left
ShenzhenGETECHCO.
,
LTD
GEEETECH
3) Thread theM10 washer < M8 spring washer < M10 nut < M10 nut< M8 spring
washer < M10 washer on the right
Step2. Assemble the 2 smooth rods
Part IDRequired numberRequired parts
NO.32M8 smooth rod
NO.394LM8UU Linear bearings
Slide 2 bearings on each smooth rod. Before you slide the bearings please make sure
they are clean.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
1.2. Attach the front and rear Acrylic support plates of the rods.
Part IDRequired numberRequired parts
NO. A9, A 102Acrylic plate( front)
NO. A 11, A 122Acrylic plate( rear)
NO.94M10 washer
NO.124M10 nut
Step1. Slide the rods into the acrylic plate; adjust the length so that the smooth rods fit
snugly between the front and rear piece.
Step2. Screw up the rods and plate with M10 nut and M10 washer.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
* Tips: the Y-axis must be a rectangle, that is the rods on both side should be parallel,
so is the front and back plate. Otherwise it will cause obstruction for the belt later.
You can use a Digital Caliper to measure.
2.2 Assemble the Y idler
Part IDRequired numberRequired parts
NO.382624ZZ Ball bearing
NO.661bearing holder
NO.271M3 x 20 screw
NO.151M3 wing nut
NO.351M4 x25 screw
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
NO.141M4 lock nut
Step1. Thread the M3 x 20 screw through the bearing holder.
Step2. Put the M4 x25 screw through the holes with the two 624ZZ bearings in
between. Lock the other end with a M4 lock nut.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
ShenzhenGETECHCO.
,
LTD
GEEETECH
Step3. Mount the assembled bearing holder onto the front support plates. And screw it
with a wing nut.
*Please leave enough room for the belt between the ball bearing and the screw.
www.geeetech.comTel:+8675526584110Fax:+8675526584074‐858
Otros manuales para Acrylic I3 Pro
10
Tabla de contenidos
Otros manuales de Impresora 3D de Geeetech
Geeetech
Geeetech A30 Pro Manual de usuario
Geeetech
Geeetech Delta Rostock mini G2 Manual de usuario
Geeetech
Geeetech Aluminum Prusa I3 Manual de usuario
Geeetech
Geeetech Prusa I3 X Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
Geeetech
Geeetech Prusa I3 X Manual de instrucciones
Geeetech
Geeetech Mizar S Manual de usuario
Geeetech
Geeetech Acrylic Prusa I3 Pro C Instrucciones de operación
Geeetech
Geeetech A20T Manual de usuario
Geeetech
Geeetech A10 Manual de usuario
Geeetech
Geeetech Prusa I3 A pro Manual de usuario
Geeetech
Geeetech GiantArm D200 Manual de usuario
Geeetech
Geeetech Prusa I3 X Manual de instrucciones
Geeetech
Geeetech E180 Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Instrucciones de operación
Geeetech
Geeetech Rostock mini Manual
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
Geeetech
Geeetech E180 Manual de usuario
Geeetech
Geeetech Delta Rostock mini G2 Manual del operador
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
