Danfoss ECtemp 532 Manual de usuario
Danfoss ECtemp 532
3Installation Guide
1 Introduction
ECtemp 532 is an electronic thermostat provided with a
2-pole switch, a room sensor to control the room tempera-
ture, and an additional oor sensor to limit the maximum
oor temperature. It can be either ush-mounted or
surface-mounted.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 5-35°C. Furthermore, it has
a LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
ectemp.danfoss.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Disposal Instruction . . . . . . . . . . . . . . . . . 14
Danfoss ECtemp 532
Installation Guide4
1.1 Technical Specications
Operation voltage 220-240 V~, 50 Hz
Standby power consump-
tion Max 0.25 W
Relay:
Resistive load
Inductive load
Max 15 A / 3450 W @ 230 V
cos φ= 0.3 max 1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0.4 °C
Ambient temperature -10 to +30 °C
Frost protection tempera-
ture 5 °C -
Temperature range
5-35°C room temperature
20-50°C oor temperature
limiter - default 35°C
Cable specication max 1x4 mm² or 2x2,5 mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Danfoss ECtemp 532
5Installation Guide
Type 1C
Storage temperature -20 to +65 °C
IP class 31
Protection class Class II -
Dimensions 85 x 85 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35°C.
Danfoss ECtemp 532
Installation Guide6
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, always place the thermostat
according to local regulation on IP classes.
Danfoss ECtemp 532
7Installation Guide
Do not place the thermostat on the inner
side of an exterior wall.
Always install the thermostat at least 50 cm.
from windows and doors.
Do not place the thermostat in a way that it
will be exposed to direct sunlight.
Note: A oor sensor enables a more
accurate temperature control and is recom-
mended in all oor heating applications
and mandatory under wooden oors to
reduce the risk of over-heating the oor.
• Place the oor sensor in a conduit in an appropriate
place where it is not exposed to sunlight or draft from
door openings.
• Equally distant and >2cm from two heating cables.
• The conduit should be ush with the oor surface -
countersink the conduit if necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be min 50mm.
Danfoss ECtemp 532
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
devireg™550
3
5
6
24
20
30
40
50
• Press the release tab in the bottom of the ther-
mostat using a at object.
• Carefully detach the front cover.
• Carefully detach the frame.
Danfoss ECtemp 532
9Installation Guide
2. Connect the thermostat according to the connection
diagram.
IP31
-10T30
D532
Mains
220-240V~
Max. Load
15 (1) A
Sensor
NL NTC
N
LOAD
L
LOAD
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the oor sensor in a conduit in
the oor.
3. Set the maximum oor temperature between 20° and
50°C by turning the screw with temperature indica-
tions in the upper left corner.
4. Mount and reassemble the thermostat:
• Fasten the thermostat to a ush-mounting box
or a surface-mounting box by driving the screws
through the holes in each side of the thermostat.
• Install the frame and front cover in the reverse
order of disassembly.
5. Turn on the power supply.
Danfoss ECtemp 532
Installation Guide10
3 Settings
How to change the minimum and maximum oor
temperatures
1. Remove the adjust-
ment button.
2. Move the pins to the
desired positions.
3. Put the adjustment
button back in place.
devireg™550
3
5
6
24
20
30
40
50
Note: Please be aware of the following:
• The oor temperature is measured where the oor
sensor is placed.
• The temperature of the bottom of a wooden oor can
be up to 10 degrees higher than the top.
• Floor manufactures often specify the max tempera-
ture on the top surface of the oor (usually 27-28˚C).
• By default, the maximum oor temperature is set to
35°C.
• Always use a oor sensor or a room + oor sensor
combination to control oor heating. Without a oor
sensor, the temperature control may be less accurate
and you risk overheating the oor.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Termostato de Danfoss
Danfoss
Danfoss RAS-D2 Combi Manual de usuario
Danfoss
Danfoss 088L5133 Manual de usuario
Danfoss
Danfoss ECtemp Smart Manual de usuario
Danfoss
Danfoss DEVIreg 610 Manual de usuario
Danfoss
Danfoss HC6000 Manual de usuario
Danfoss
Danfoss RET B + RF Instrucciones de funcionamiento
Danfoss
Danfoss 140F1143 Manual de usuario
Danfoss
Danfoss 103E5 Manual de usuario
Danfoss
Danfoss DEVI DEVIreg Touch Manual de usuario
Danfoss
Danfoss ST-S2 Manual de usuario
Danfoss
Danfoss TP9000 Si Manual de usuario
Danfoss
Danfoss HP75-1 Manual de usuario
Danfoss
Danfoss HP8211-1RJ Manual de usuario
Danfoss
Danfoss KP 61 Manual de usuario
Danfoss
Danfoss TS715Si Manual de usuario
Danfoss
Danfoss Link DBR Manual de usuario
Danfoss
Danfoss MTD Instrucciones de montaje
Danfoss
Danfoss TP5001 series Manual de usuario
Danfoss
Danfoss Icon Master Manual de usuario
Danfoss
Danfoss DEVI DEVIreg 532 Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
