Danfoss Living connect Manual de usuario

Application

This documents provides information about the

Z-Wave commands supported by living connect®

and guidelines on the implementation of Z-Wave

controllers as well as general description of the

living connect® and how to mount it on a radiator.

living connect®is a electronic radiator thermostat.

It can be controlled by either a Danfoss LinkTM CC

(Central Controller) or a Z-Wave certified control-

ler.

(For control by Danfos LinkTM CC see separate da-

ta sheet)

living connect® uses Z-Wave wireless communica-

tion technology, is easy to install and is supplied

with adapters for all thermostatic valves manu-

factured by Danfoss and most other radiator

valve manufacturers.

living connect® is battery powered, compact and

very easy to operate with only three buttons on

the front.

The temperature can be changed at any time us-

ing the buttons on living connect®. The change is

transmitted directly to the controller, which can

synchronize the other electronic radiator thermo-

stats in the same room. living connect® features

an open-window function, which closes the valve

if the temperature in the room is falling dramati-

cally. Main features in a system with the control-

ler:

▪Energy saving

▪Easy to install

▪Easy to operate - only three buttons

▪Provides high comfort

▪Open window function

▪Valve exercise function

▪PID control

▪Weekly programs with variable set points for

each day

▪Battery lifetime 2 years, if properly suppor-

ted by the Z-Wave controller

▪Child lock

▪Frost protection

▪Backlit display

System example

Data Sheet

living connect®, Z-Wave Certified Electronic Ra-

diator Thermostat

Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 1

Code numbers Code no. Adapter (included) Language instructions

014G0001 Danfoss RA UK/DE/DK/NL

FR/PL/SE/FI

014G0002 Danfoss RA and M30 x 1.5 (K) UK/DE/DK/NL

FR/PL/SE/FI

Accessories Type Code no.

RAV & RAVL adaptor 014G0250

RA adaptor 014G0251

M30 x 1.5 (K) adaptor 014G0252

RTD adaptor 014G0253

Specification Control system/input Standard Z-Wave control units

Transmission frequency Wireless Z-Wave/868.42 MHz

Transmission range Up to 30 meters

Synchronizing Configurable (5 min. recommended)

Screen/display Grey digital with backlit

Actuator type Electromechanical

Software classification A

Control PID

Power supply 2x1.5V AA alkaline, class III (SELV)

Battery life 2 years

Low battery signal Battery icon and alarm bell will flash in display. If the battery

level is critical, the whole display will flash.

Ambient temperature 0 to 40⁰C

Transportation temperature range -20 to 65⁰C

Temperature setting range 4 to 28⁰C

Recommended use Residential

Open-window function Yes

Size RA: L: 91 mm Ø:51 mm/K: L78 mm Ø: 51 mm

Noise level < 30 dBA

Weight incl. battery 177 g

Safety classification Type 1

Mechanical strength 70 N (max. force from valve)

Maximum water temperature 90°C

Movement type Linear

Spindle movement 2-3 mm on valve

Maximum extension 4.5 mm

Temperature sampling Measures temperature every minute

Speed of adjustment 1 mm/s

Power consumption 3 mW in standby, 1.2 W when active

Ball pressure test 75°C

IP class* 20

* This thermostat should not be used in hazardous installations or in places where it will be exposed

to water.

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

2 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions

Marking

Installation living connect® is supplied with adapters for

Danfoss RA valves and valves with M30X1.5

(K) connections (code no. 014G0002), two al-

kaline AA batteries and a 2 mm Allen key.

Inserting the batteries

Remove the battery cover and insert the two

batteries. Ensure that the batteries are cor-

rectly inserted. A capital "M" must flash on the

display before installation.

RA K

▪Start by mounting the adapter.

▪Tighten the RA adapter using the Allen

key. Tighten the K adapter by hand (max.

5 Nm).

▪Screw the thermostat onto the adapter

and hand-tighten (max. 5 Nm).

2 mm Allen key

▪Press and hold for approx. 3 seconds

to fix the thermostat.

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 3

Connecting living connect®

to a Z-Wave controller

In Z-Wave connecting a device is called “Inclusion” or “Learn mode”.

To connect living connect® to a Z-Wave controller then:

▪Ensure living connect® is factory reset as explained in the user manual.

▪Activate "Inclusion" on the Z-Wave controller.

▪Quickly press and release the select button on living connect®.

▪Observe both controller and living connect® for status of the process.

Technical requirements:

▪After a succesful "Inclusion" the controller must send a WAKE_UP_INTERVAL_SET command to

living connect® in order to specify where and when living connect® should communicate wire-

lessly.

▪After sending the WAKE_UP_INTERVAL_SET command, the controller must assign return routes,

so living connect® can reach its destination i.e. the nodeID set in the WAKE_UP_INTERVAL_SET

command.

▪living connect® will not commence its periodic communications if it is in "Installation mode". "In-

stallation mode" is for physical installation and should not be confused with "Inclusion". Please

consult the user manual of living connect® for instructions on how to leave "Installation mode".

▪A Z-Wave controller will have access to all living connect® features, which are exposed using

standard Z-Wave command classes.

See other section of this document for more information.

Disconnecting living con-

nect® from a Z-Wave con-

troller

In Z-Wave disconnecting a device is called “Exclusion”.

To disconnect living connect® from a Z-Wave controller then:

▪Activate "Exclusion" on the Z-Wave controller.

▪Quickly press and release the select button on living connect®.

▪Observe both controller and living connect® for status of the process.

Activate special awake

mode on living connect®

living connect® will turn on radio communication for short periods of time at specific intervals in or-

der to communicate with its controller, unless such a controller has yet to be configured. When radio

communication is not needed by living connect® it will turn the radio off to conserve battery life.

If a user needs to configure a controller for living connect® or send more information to living con-

nect® then the user can activate a special 5 seconds awake mode by pressing the select button on

living connect®.

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

4 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions

Important ▪The nodeID set in the WAKE_UP_INTERVAL_SET command must be for a permanently listening

device which reponds to the commands sent from living connect®. This means PC's with USB

sticks will only work if the PC is never turned off. If the controller is turned off for extended peri-

odes, living connect® will use the batteries too fast.

▪To preserve battery - Wake_Up_intervals should not be set to less than 5 min. Increasing the

time between intervals will increase battery life but can reduce user satisfaction due to long re-

action times.

▪Although living connect® supports single commands, multi commands must always be used to

ensure two years battery lifetime.

▪If multiple thermostats are installed in the same room it is important that the controller ensures

that they all have the same schedule and the same setpoint.

▪In order to ensure proper routing with battery operated devices, the controller must support

SUC.

living connect® and Z-

Wave repeaters

living connect® may benefit if more mains powered Z-Wave devices are added to a Z-Wave network.

Mains powered Z-Wave devices improve the reliability of a Z-Wave network as they can act as re-

peaters and thus provide alternate routes for communication.

Implemented Z-Wave de-

vice classes

Z-Wave Device Classes Device Class Implemented

Generic Device GENERIC_TYPE_THERMOSTAT

Specific Device SPECIFIC_TYPE_SETPOINT_THERMOSTAT

Supported and controlled

Z-Wave command classes

Z-Wave Command Classes Supported Description

COMMAND_CLASS_BATTERY Get current battery status of living connect®.

COMMAND_CLASS_CLIMATE_CONTROL_SCHEDULE Control a temperature offset to the ther-

mostat setpoint of living connect®. The tem-

perature offset is defined by schedules and

schedule overrides.

COMMAND_CLASS_CLOCK Set or get the current living connect® clock.

COMMAND_CLASS_MANUFACTURER_PROPRIETARY Special command used for communication

with a Danfoss Link system.

COMMAND_CLASS_MANUFACTURER_SPECIFIC Get manufacturer ID of system.

COMMAND_CLASS_MULTI_CMD A special Z-Wave command used by living

connect® to encapsulate multiple com-

mands in one command and thereby con-

serve battery life.

COMMAND_CLASS_PROTECTION Set or get living connect® local protection

mode.Possible local protection values are:

0 = no protection

2 = fully locked (tamperproof)

COMMAND_CLASS_THERMOSTAT_SETPOINT Set or get current thermostat setpoint of

living connect®.Heating setpoint is the only

supported setpoint type.

COMMAND_CLASS_VERSION Get version of product and command

classes.

COMMAND_CLASS_WAKE_UP A special Z-Wave command used by living

connect® to synchronize communication

with its controller.

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 5

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

6 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 7

Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat

Danfoss A/S

Heating Solutions

Haarupvaenget 11

8600 Silkeborg

Denmark

Phone:+45 7488 8000

Fax: +45 7488 8100

Email: [email protected]

www.heating.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective

8 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions

Otros manuales para living connect

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss Living Eco Manual de usuario

Danfoss

Danfoss RET2000 M Manual de usuario

Danfoss

Danfoss 100064 Manual de usuario

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss DEVIreg 610 Manual de usuario

Danfoss

Danfoss TP9000 Si Manual de usuario

Danfoss

Danfoss TP4000 Range Manual de usuario

Danfoss

Danfoss ECL Comfort 310, A367 Manual de usuario

Danfoss

Danfoss TP7001 series Manual de usuario

Danfoss

Danfoss CF-RF Manual de usuario

Danfoss

Danfoss HC6110-3 Manual de usuario

Danfoss

Danfoss GreenCon RC-T2 Manual de usuario

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss TP5001 series Manual de usuario

Danfoss

Danfoss ECtemp Touch Manual de usuario

Danfoss

Danfoss C67 Manual de usuario

Danfoss

Danfoss CF-RP 088U0211 Manual de usuario

Danfoss

Danfoss ECtemp Next Plus Manual de usuario

Danfoss

Danfoss RT 103 Manual de usuario

Danfoss

Danfoss RAVV-RAV8 Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de funcionamiento

Danfoss

Danfoss RET B-LS Manual de usuario

Danfoss

Danfoss TP5000 RF Si Manual de usuario

Danfoss

Danfoss ECL Comfort 310, A333 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Danfoss living connect Manual de usuario

Manuales populares de Termostato de otras marcas