CYP PU-8H8HBTE Manual de usuario

38++%7(38++%7(

[[+'0,+'%DVH70DWUL[

3OD\LQFOXGLQ /$1VHUYLQ 

23(5$7,210$18$/

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

 

electrical shock and injury to persons.

 

moisture or install this product near water.

 Never spill liquid of any kind on or into this product.

 Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

 Do not attach the power supply cabling to building surfaces.

 Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

 Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

 To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for



REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

RDV1 11/06/11 Preliminary Release

RDV2 13/06/11 Add CMSI-4H8CVE

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 2

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel.........................................4

6.3 Side Panel .........................................5

6.4 Remote Control................................6

6.5 IR Cable Pin Assignment..................6

6.6 RS-232 Protocols ...............................7

6.7 RS-232 & Telnet Commands............8

6.8 Telnet Control ...................................9

6.9 Web GUI Control ............................11

7. Connection Diagram .......................... 13

 ...................................... 15

9. Acronyms ............................................. 16

1. INTRODUCTION







outputs. It supports digital audio formats such as LPCM 7.1CH, Dolby

TrueHD, Dolby Digital Plus and DTS-HD Master Audio. Also, 3D content



allows the connection of source equipment to output displays, over

distances of up to 100 meters along with IR and RS-232(includes telnet)

control and PoE features. Further, it allows all outputs with access of

ethernetfunction through the single LAN port's active connection on

the device.

2. APPLICATIONS

 HDMI System control

 Video/TV wall display and control

 Security surveillance and control

 Commercial advertising, displaying and control

 Lecture room display and control

 Hyper market demonstration and control

3. PACKAGE CONTENTS

 

 HDMI over CAT5e/6/7 Receiver (Optional)

 

 2×IR Blaster

 2×24 V/6.25 A DC Power Adaptor (1 for PoE)

 1×IR Remote Control

 Operation Manual

4. SYSTEM REQUIREMENTS

 HDMI equipped input source devices with HDMI cables

 HDMI equipped output displays (TVs or monitors) or HDMI equipped

AV receivers with HDMI cables

 Industry CAT5e/6/7 cables

5. FEATURES

 HDMI, HDCP1.1 and DVI compliant

 Supports HDMI 3D features

 Supports resolutions VGA~WUXGA and 480i~1080p dependent upon

the output display’s EDID settings

 Supports distances up to 100 meters through CAT5e/6/7 cables

 Supports 3D signal display dependent upon the output display EDID

settings

 Supports PoE (Power over Ethernet) on compatible receivers only

 Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters

at 12-bit resolution

 Supports IR in/out from input and output locations

 Supports RS-232(include Telnet), remote control and on-panel

control

 Supports IP function through the single LAN port

 

 

 Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD

Master Audio transmission

Note: 1.The PoE function is designed for powering compatible

receiver units onlynon-PoE receivers will need their own

power supply.Receivers of another brand may not be

compatible.

2.LAN/CONTROL port must not miss connected with CAT

outputs, doing so will destroy the device.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER LOCK

MENU OUTA 1B2C3D4

E5F6G7H8

8X8 HDMI MATRIX over CAT5e/6 CMSI-8H8CVE

2 3 4 5 61

1LCM : Displays the setting information of each input and output

setting.

2POWER: Press this button to power the device on/off. The LED will

illuminate green when the power is on, red when it is in 'Standby'

mode.

3LOCK: Press this button to lock all the buttons on the panel; press

again to unlock. The LED will illuminate green when locked.

4IR: IR Receiver window (accepts the remote control signal of this

device only).

5MENU: Press this button to change the EDID setting from STD



selection.

61~8/A~H and In/Out: Press the Out or In button to select the output

or input mode and then press the required number button to make

the selection accordingly.

 

E~H need to be set to input 2, then the following sequence of

button presses need to be performed:

 



Note: If the menu button is not pressed the selection will not be

changed.

6.2 Rear Panel

LAN

RS232

SERVICE

IR OUT

IR IN

IR OUT

IR IN

IR OUT

IR IN

ALL A B C D E F G H

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUTCAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

MAIN 24V

POE 24V

HDMI IN

V+

GND

GND GND

V+

2 4

510 111

1LAN: Connect an active Ethernet port for network signal sharing

with receivers with LAN function for a data transmission rate of

100Mbps or when anyone of the receivers connected to this

device is connect with an active Ethernet port all receivers with

LAN function and this device will also access the Ethernet function.

This port is also the link for Telnet system and web GUI controls,

further details please referes to section 6.8 & 6.9.

2RS-232: Connect to a PC or laptop with D-Sub 9-pin cable for the

transmission of RS-232 commands.

3ALL IR OUT: Connect to the IR blaster (included in the package) for IR

signal transmission of the source or display equipment. Place the IR

blaster in direct line-of-sight of the equipment to be controlled.

4ALL IR IN:

IR signal reception of the remote control of this device or the source

and display equipment. Ensure that remote being used is within the



5SERVICE: Manufacturer use only.

6IR OUT 1~8: Connect the supplied IR blasters (included in the

package) for IR signal transmission. Place the IR blaster in direct line-

of-sight of the equipment to be controlled.

7IR IN 1~8:

package) for IR signal reception. Ensure that remote being used is



8CAT5e/6/7 OUT 1~8: Connect to the CAT input port of receiver units

with a single CAT5e/6/7 cable for HDMI Audio/Video and IR/RS-232

control signal sending.

Warning: Please do not miss connect CAT5e/6/7 ports with receiver

device's LAN port doing so will destroy the device.

9HDMI IN 1~8: Connect to the HDMI input source devices such as a



10 DC 24V MAIN POWER: Plug the 24 V DC power supply into the unit

and connect the adaptor to an AC outlet.

11 PoE 24V: Plug the 24 V PoE power supply into the unit and connect

the adaptor to an AC outlet. This unit will mainly power PoE (Power

over Ethernet) capaable receiver units.

6.3 Side Panel

1Fan Ventilator: These are air ventilation areas, DO NOT block these

areas or cover it with any object. Please allow adequate space

around the unit for air circulation.

6.4 Remote Control

1POWER: Press this button to

switch on the device or set it to

standby mode.

2IN: Input ports selection 1~8.

3OUT: Output ports selection A~H.

6.5 IR Cable Pin Assignment

Power 5 V

IR Blaster Signal

IR Signal

Power 5 V

Grounding

IR Receiver

IR Blaster

6.6 RS-232 Protocols

Pin Assignment

CMSI-8H8CVE/CMSI-4H8CVE Remote Control Console

PIN Assignment PIN Assignment

1NC 1NC

2 2

3 3

4NC 4NC

5 GND 5 GND

6NC 6NC

7NC 7NC

8NC 8NC

9NC 9NC

Baud Rate: 19200 bps

Data bit: 8 bits

Parity: None

Stop Bit: 1

Flow Control: None

Otros manuales para PU-8H8HBTE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de CYP

CYP

CYP PUV-44XPL-AVLC Manual de usuario

CYP

CYP CMSI-8H8HC Manual de usuario

CYP

CYP EL-42M-PIP Manual de usuario

CYP

CYP CMLUX-44S Manual de usuario

CYP

CYP CPLUS-662CVEA Manual de usuario

CYP

CYP CMSI-8H8HS Manual de usuario

CYP

CYP CPLUS-1082CVEA Manual de usuario

CYP

CYP PU-8H8HBTPL Manual de usuario

CYP

CYP PU-O4H4C Manual de usuario

CYP

CYP SM-4X2-HDMI-LC Manual de usuario

CYP

CYP OR-44-4K22 Manual de usuario

CYP

CYP HDBT PU-4H4HBTE-4K Manual de usuario

CYP

CYP CMSI-1616 Manual de usuario

CYP

CYP SM-2X4-HDMI-LC Manual de usuario

CYP

CYP CMSI-8H8HS Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

CYP

CYP CMSI-8H8CV Manual de usuario

CYP

CYP CMPRO-4H4H Manual de usuario

CYP

CYP OR-HD88S Manual de usuario

CYP

CYP CMPRO-U4H4CVE Manual de usuario

CYP

CYP PUV-1082-4K22N Manual de usuario

CYP

CYP Elpro Video Labs CDPS-UC4H4HFS Manual de usuario

CYP

CYP PUV-1210PL-RX Manual de usuario

CYP

CYP MOD-32 Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario