CYP CMSI-8H8CV Manual de usuario

CMSI-8H8CV

HDBaseT™ 8×8 HDMI Matrix over CAT5e/6/7

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 13/11/12 Preliminary Release

VR1 04/06/13 RS-232 & Telnet's SetIP Command

VS1 04/11/13 Separated 4x4 and 8x8 Manuals

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 2

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel.........................................3

6.2 Rear Panel .........................................4

6.3 Side Panel ..........................................5

6.4 Remote Control.................................5

6.5 IR Cable Pin Assignment ..................6

6.6 RS-232 Pin Assignment ......................6

6.7 RS-232 and Telnet Commands ........7

6.8 Telnet Control ....................................9

6.9 Web GUI Control.............................11

7. Connection Diagram .......................... 13

8. Specications ...................................... 15

8.1 Technical Specications ................15

8.2 CAT5e/6/7 Cable Specication ....16

9. Acronyms ............................................. 16

1. INTRODUCTION

The HDBaseT™ 8 by 8 HDMI Matrix over CAT5e/6/7 supports

the transmission of video (resolutions up to 1080p Full HD and

1920×1200@60Hz) and multi-channel digital audio from eight high

denition sources to eight outputs over a single CAT5e/6/7 cable

(up to 100m) for each output. It supports high resolution digital audio

formats such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-

HD Master Audio as well as 3D content that can be displayed when

connecting a 3DTV and 3D source. The matrix can be controlled

via IR, RS-232, Telnet or Web GUI. Power over Ethernet (PoE) support

means that compatible receivers do not need their own seperate

power supplies, allowing for greater exibility in installations.

2. APPLICATIONS

• HDMI Matrix System

• Video/TV wall display and control

• Security surveillance and control

• Commercial advertising, display and control

• University lecture hall, display and control

• Retail sales and demonstration

3. PACKAGE CONTENTS

• 1×HDBaseT™ 8 by 8 HDMI Matrix over CAT5e/6/7

• 2×IR Extender

• 2×IR Blaster

• 1×IR Remote Control

• 2×24 V/6.25 A DC Power Adaptor (1 for PoE)

• Operation Manual

4. SYSTEM REQUIREMENTS

• HDMI equipped source devices, connect with HDMI cables or DVI

equipped source, connect with DVI to HDMI cables

• HDMI equipped displays (TVs or monitors) or HDMI equipped AV

receivers, connected with HDMI cables

• Industry standard CAT5e/6/7 cables

• HDBaseT™ Receivers (CH-506RX, CH-507RX or CH-1109RX)

5. FEATURES

• HDMI, HDCP1.1 and DVI compliant

• Supports HDMI 3D features

• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon

the output display’s EDID settings

• Supports 3D signal display dependent upon the output display EDID

settings

• Supports PoE (Power over Ethernet) on compatible receivers only

• Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters

at 12-bit resolution

• Supports bi-directional IR to and from input and output locations

• Supports control via RS-232, IR remote, on-panel buttons and IP

(Telnet & Web GUI)

• 2U size design

• Supports external and internal EDID settings

• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD

Master Audio transmission

Note:

1. The PoE function is designed for powering compatible receiver

units only—non-PoE receivers will need their own power supply.

Receivers of another brand may not be compatible.

2. Do not connect the CONTROL port to CAT outputs of this device

or to CAT inputs or receiver. Doing so may demage the unit.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER LOCK

MENU OUTA 1B2C3D4

E5F6G7H8

8X8 HDMI MATRIX over CAT5e/6 CMSI-8H8CV

2 3 4 5 61

1LCM: Displays the setting information of each input and output

setting.

2POWER: Press this button to power the device on/off. The LED will

illuminate green when the power is on, red when it is in 'Standby'

mode.

3LOCK: Press this button to lock all the buttons on the panel; press

again to unlock. The LED will illuminate green when locked.

4IR: IR Receiver window (accepts the remote control signal of this

device only) with IR frequency of 38 kHz.

5MENU: Press this button to access the LCM menu system, from

here EDID settings can be managed and IP system settings are

displayed.

61~8/A~H and OUT/IN: Press the OUT or IN button to select the

output or input mode and then press the required number button

to make the selection accordingly.

For example, if outputs A~D need to be set to input 1 and outputs

E~H need to be set to input 2, then the following sequence of

button presses need to be performed:

Press: OUTABCDIN1MENU,

and then press: OUTEFGHIN2MENU.

Note: If the MENU button is not pressed the selection will not be

changed.

6.2 Rear Panel

CONTROL

RS232

SERVICE

IR OUT

IR IN

IR OUT

IR IN

IR OUT

IR IN

ALL A B C D E F G H

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUTCAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

MAIN 24V

POE 24V

HDMI IN

V+

GND

GND GND

V+

510 111

1CONTROL: This port is the link for Telnet or Web GUI controls, connect

to an active Ethernet link with an RJ45 terminated cable (for further

details on IP control, please refer to sections 6.8 & 6.9).

Warning: Please do not connect this port directly to the PC/Laptop as the

Telnet function will not work.

2RS-232: Connect to a PC or control system with D-Sub 9-pin cable

for control of the matrix via RS-232 commands (please refer to

Section 6.7 for a list of commands).

3ALL IR OUT: Connect to the IR blaster for IR signal transmission to the

source devices. Place the IR blaster in direct line-of-sight of the

equipment to be controlled. All signals received from the display

side will be relayed to the source devices.

4ALL IR IN: Connect to the IR extender for IR signal reception. Ensure

that the remote being used is within the direct line-of-sight of the IR

extender. It will transmit all signals received through the IR ALL OUT.

5SERVICE: Manufacturer use only.

6IR OUT A~H: Connect to the IR blasters for IR signal transmission.

Place the IR blaster in direct line-of-sight of the equipment to be

controlled. It will transmit the IR signal received from the receiver

side according to the selected input.

7IR IN 1~8: Connect to the IR extenders for IR signal reception. Ensure

that the remote being used is within the direct line-of-sight of the

IR extender. It will send out the IR signal received to the selected IR

OUT (A-H).

8CAT5e/6/7 OUT A~H: Connect the CAT outputs to the CAT input port

of the receiver units with a single CAT5e/6/7 cable for HDMI Audio/

Video and IR control signal transmission.

Warning: Please do not connect the CAT5e/6/7 outputs to the

receiver's LAN port.

9HDMI IN 1~8: Connect to the HDMI source devices such as a DVD

player or a Set-top Box with HDMI cables or DVI to HDMI cables.

10 DC 24V: Connect the 24 V DC power supply to the unit and plug the

adaptor into an AC outlet.

11 PoE 24V: Connect the 24V PoE power supply into the unit and plug

the adaptor into an AC outlet. This unit will mainly power PoE (Power

over Ethernet) capable receiver units.

6.3 Side Panel

1Fan Ventilator: These are air ventilation areas, DO NOT block these

areas or cover it with any object. Please allow adequate space

around the unit for air circulation.

6.4 Remote Control

1POWER: Press this button to switch

the device 'ON' or set it to standby

mode.

2IN: Input selection 1~8.

3OUT: Output selection A~H.

Note: When the IR remote is used

in the Output Zone the user only

needs to select the desired input

(1~8)

Tabla de contenidos

Otros manuales de Conmutador de matriz de CYP

CYP

CYP CMSI-4H4CVL Manual de usuario

CYP

CYP OR-44VWC Manual de usuario

CYP

CYP CMLUX-44S Manual de usuario

CYP

CYP SM-2X4-HDMI-LC Manual de usuario

CYP

CYP PU-8H8HBTL Manual de usuario

CYP

CYP CPLUS-662CVEA Manual de usuario

CYP

CYP OR-HD88HC Manual de usuario

CYP

CYP CMPRO-UA8H8CVPL Manual de usuario

CYP

CYP CMPRO-U8H8CVE Manual de usuario

CYP

CYP CPLUS-V8H8HP Manual de usuario

CYP

CYP CDPS-44SM Manual de usuario

CYP

CYP EL-42M-PIP Manual de usuario

CYP

CYP MOD-32 Manual de usuario

CYP

CYP Elpro Video Labs CDPS-UC4H4HFS Manual de usuario

CYP

CYP CPLUS-V4H4HPA Manual de usuario

CYP

CYP PU-8H8HBTE-4K Manual de usuario

CYP

CYP OR-IR88 Manual de usuario

CYP

CYP CMSI-3232 Manual de usuario

CYP

CYP PUV-1210PL-RX Manual de usuario

CYP

CYP CMSI-8D8DS Manual de usuario

CYP

CYP PU-8H8HBTPL-4K Manual de usuario

CYP

CYP PU-424HBTL-KIT Manual de usuario

CYP

CYP CPLUS-32FX Manual de usuario

CYP

CYP CMIR-882 Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario