CYP QU-14S-4K22 Manual de usuario

QU-14S-4K22

1 to 4 HDMI Distribution Amplier

(4K & HDCP2.2 support)

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sucient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 17/04/2015 First release

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................6

5. Features..................................................7

6. Operation Controls and Functions.......8

6.1 Front Panel................................................... 8

6.2 Rear Panel..................................................... 9

7. Connection Diagram .......................... 10

8. Specications...................................... 11

8.1 Technical Specications ........................11

8.2 Supported Resolutions.........................12

9. Acronyms............................................. 13

1. INTRODUCTION

The QU-12S-4K Distribution Amplier (splitter) accepts one HDMI input

and splits this signal to two identical outputs. This device is v1.4 HDMI

compliant and supports HDCP (including HDCP 2.2), 3D Video signals,

‘Deep Colour', and 4K resolutions, together with High Denition Audio.

Each buered output can run 1080p/8-bit up to 20 metres and can also

be cascaded up to 3 layers.

2. APPLICATIONS

Simultaneously display an HDMI source on 2 TVs/projectors

Showroom display

University lecture hall display

Retail sales displays

3. PACKAGE CONTENTS

1×1 by 2 HDMI 4K UHD Splitter

1×5V/2.6A Power Adaptor

1×Operation Manual

4. SYSTEM REQUIREMENTS

HDMI source device such as a DVD/Blu-ray player and HDMI equipped

display (TVs/monitors) with High Speed HDMI cables.

5. FEATURES

v1.4 HDMI, HDCP compliant (including HDCP 2.2) and DVI 1.0

compliant

HDMI 1 to 2 Splitter

Supports resolutions VGA~WUXGA, 480i~1080p, 4K UHD@24/25/30Hz

(RGB 4:4:4 & YUV 4:2:2), 4K UHD@ 60Hz (YUV 4:2:0), 4K/2K@24/25/30Hz

(RGB 4:4:4 & YUV 4:2:2) and 4K/2K@ 60Hz (YUV 4:2:0) dependent upon

the output display’s EDID settings

High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus

and DTS-HD Master Audio plus LPCM

Auto signal amplication & equalisation improves signal transmission

distances

Supports CEC bypass

Supports Deep Colour

Power LED indicator

Supports xvYCC

Supports 3D signals

Note: For playback of 4K2K HDMI source signals, a 4K2K capable display and

High Speed HDMI cables are required.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

HDMI 1x2 SPLITTER

SYNC

HDCP 2.2

21IN

12 3 4 5

POWER: This LED will illuminate when the unit is connected to an

active power supply and switched on.

SYNC IN: This LED will illuminate when the unit is connected with

active signal from the source device.

HDCP 2.2 IN: This LED will illuminate when the source signal is HDCP

2.2 encrypted.

SYNC OUT 1~2: These LEDs will illuminate when the output detects a

connected display.

HDCP 2.2 OUT 1~2: These LEDs will illuminate when the connected

HDMI display are HDCP 2.2 compatible.

6.2 Rear Panel

HDMI IN

EDID

STD TV

DC 5V

HDMI OUT

FIRMWARE

1 52 3 4

HDMI IN: Connect this input to the HDMI or DVI output of your source

device such as a DVD player or Set-top Box with an HDMI cable.

HDMI OUT 1~2: Connect to an HDMI equipped display (TV/monitor)

or HD Amplier for simultaneous HDMI distribution.

EDID TV/STD: Use this switch to set HDMI EDID setting.

TV: When in 'TV' mode, the unit will read the EDID settings of the

display connected to HDMI OUT 1. If it detects a 4K2K capable EDID

setting it will transmit the signal in that format to all outputs. If no

4K2K capable EDID setting is detected then the unit will output the

best resolution that all displays can support.

Note: When Output 1 is connected to a 4K2K display and Output 2 is

connected to non-4K2K display no picture may be displayed. To ensure

proper display all screens must all be capable of displaying the same

resolution.

STD: When in 'STD' mode, the unit will use its own built-in EDID

settings. In this mode, the video output will be set to 1080p@60Hz

and the audio output at LPCM 2CH Stereo. Use this mode if there are

display problems in 'TV' Mode.

Note: The unit will retain and use the EDID settings of the last display

connected to the HDMI OUT 1 output if no display is connected to this

output even after switching EDID modes or a power cycle.

FIRMWARE: Manufacturer use only.

DC 5V: Plug the supplied power supply into the unit and connect the

adaptor to an AC outlet.

7. CONNECTION DIAGRAM

HDMI IN

EDID

STDTV

DC 5V

HDMI OUT

FIRMWARE

DVD/Blu-ray Player

HDTVProjector

Power

Supply

HDMI

Input

Simultaneous

HDMI Outputs

Tabla de contenidos

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario