Concept Pro AIR3526-AHD2M Manual de usuario
AHD CAMERA QUICK START GUIDE
QUICK START GUIDE
Technical Documents
AIR3526-AHD2M
AIR3526-AHD5M-Z
AHD External Medium Bullet Camera
AHD CAMERA QUICK START GUIDE
1. WHAT’S IN THE BOX?
1. CONTENTS
Packaging Contents
Technical Documents 4-in-1 AHD Camera x1 Quick Start Guide x1
Fitting Screws x3 Wall Plugs x3
Sunshield x1 Sunshield Bolt x1
Mounting Template x1 Allen Key x1
Analogue SVO Cable x1
2. INSTALLATION
Important: Ensure all precautionary procedures are observed during installation.
It is recommended that the camera is tested in low light and day light conditions
at the point on installation to ensure continuity of effective CCTV monitoring.
1. Open Packaging
Open packaging, remove camera, and set aside the
included accessories. Locate the cable cutout on the
side desired.
2. Drill Mounting Holes
Attach the included mounting template on the
mounting surface and drill holes according to the
template. Insert included wall plugs into the holes.
3. Mount the Camera
Insert cables through the mounting hole.
Position the camera over the mounting holes and use
the included tting screws to afx the camera to the
mounting surface.
4. Adjust Camera Positioning
Loosen locking screws and axes to move the camera
to the desired monitoring angle. Re-tighten after the
desired angle is found.
2
3
4
1
AHD CAMERA QUICK START GUIDE
3. CONFIGURING THE CAMERA
Outer Camera Connections
PSU
Power Input
Video Output
- Connect the video output to a video cable running to the recorder/monitor.
- Check the power supply is of the correct level and connect the power supply to the
camera power input.
- View the picture on a monitoring device to check the power and video connection is
properly working.
- To assist in installation when using an analogue test monitor, the camera can be switched
to an analogue output by pushing up on the OSD Button for several seconds.
- The camera can be returned to AHD output by pushing left on the OSD Button for several seconds.
On-Screen Display (OSD Controller)
1. Use the included allen key
accessory to open the service
hatch on the underside of the
camera. The buttons in this hatch
can be used to operate the
camera on-screen display (OSD)
menu and change video format.
2. Press and hold LEFT for 5 seconds to
switch the camera to AHD.
3. Press and hold RIGHT for 5 seconds
to switch the camera to TVI.
4. Press and hold UP for 5 seconds
to switch the camera to CVBS or
Analogue.
5. Press and hold DOWN for 5 seconds
to switch the camera to CVI.
UP
LEFT
RIGHT
DOWN MENU / ENTER
AHD CAMERA QUICK START GUIDE
4. On-Screen Display
MAIN MENU
AE
WB
DAY-NIGHT
VIDEO SETTING
LANGUAGE:
RESET
SAVE-EXIT
EXIT
ENGLISH, CHINESE, SPANISH, KOREAN, ITALIAN
CONTRAST:
SHARPNESS:
COLOR GAIN:
DNR:
IMAGE SIZE:
FORMAT:
RETURN
1080P, 720P
PAL, NTSC
DAY / NIGHT
MODE:
RETURN
EXT, AUTO, COLOR, B/W
WB
MODE:
RGAIN
(MODE = MWB) :
BGAIN
(MODE = MWB):
RETURN
ATW, MWB
EXPOSURE
BRIGHTNESS:
EXPOSURE MODE:
LV (EXPOSURE
MODE = BLC):
GAIN:
RETURN
1-20
2MP: GLOBE, CENTER, BLC, FLC
5MP: GLOBE, BLC
2MP: 0-8
5MP: 1-9
2MP: 1-16
5MP: 1-127
2MP: 1-16
5MP: 1-127
2MP: 1-50 5MP: 1-16
HD:
5MP20, 5MP12.5, 4MP30, 4MP25, 4MP15,
1080P25, 1080P30, SD (PAL/NTSC)
AHD, TVI, CVI, CVBS
VIDEO STANDARD:
2MP: 1-20 5MP: 1-16
2MP: 1-31 5MP: 1-16
2MP: 1-15 5MP: 1-16
2MP: 1-16
MIRROR: 5MP: DEFAULT, H, V, HV
VIDEO SETTING/IMAGE ENHANCE
VIDEO OUTPUT (5MP MODELS)
AHD CAMERA QUICK START GUIDE
5. Troubleshooting
- Ensure all power and cable connections are correct between the camera and recorder.
- If all power and cable connections are correct and the camera picture does not appear,
contact your supplier for technical support.
- Ensure that the digital video recorder supports the camera’s specied resolution and
format. Try switching the camera to CVBS format with the OSD joystick to conrm the
image appears on the DVR, then switch the camera to a supported format and resolution.
6. Caution
Safety Precautions
1. This installation should be made by qualied service personnel and should adhere to all
local codes.
2. Avoid installation on a surface subjected to frequent vibration or shocks.
3. Do not operate the camera beyond its specied temperature range or power source
ratings.
4. Should any damage or suspected damage occur, shutdown the power source, unplug
the camera, and contact your service provider.
5. Do not install the camera under unstable lighting conditions. Severe lighting change or
icker can cause the camera to work improperly.
6. Never use the camera close to a gas or oil leak.
7. Do not disassemble the camera.
8. Never let the camera directly face a strong light source.
9. Ensure all removable covers are replaced to protect the inner components.
10. Do not install near devices which emit a strong electro-magnetic eld.
11. Use a dry or damp cloth only for cleaning.
12. Do not drop the camera or subject the unit to physical shocks.
CAUTION
PLEASE FOLLOW THE ABOVE PRECAUTIONS – FAILURE TO DO SO MAY INVALIDATE THE
WARRANTY OR CAUSE SERIOUS INJURY.
Note: Changes or modications not expressly approved by the manufacturer can cause the
camera to be damaged and become inoperable. This may invalidate the user warranty.
AHD CAMERA QUICK START GUIDE
7. Dimensions
All measurements are in mm.
93mm
AHD CAMERA QUICK START GUIDE
NOTES
AIR3526-AHD Quick Start GuideJan 2019
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Concept Pro
Concept Pro
Concept Pro VCP7236 Manual de usuario
Concept Pro
Concept Pro CPL-MVIR-IP2M/2.8 Manual de usuario
Concept Pro
Concept Pro VHSDIR-670EXT-IP Manual de usuario
Concept Pro
Concept Pro CVP9324DNIR-HDA-3MP Manual de usuario
Concept Pro
Concept Pro AIR8012-IP3M-Z Manual de usuario
Concept Pro
Concept Pro AIR3016 Manual de usuario
Concept Pro
Concept Pro AIR8012-IP3M-Z Manual de usuario
Concept Pro
Concept Pro VHSDIR-812EXT-IP3M Manual de usuario
Concept Pro
Concept Pro CBP360-HD Manual de usuario
Concept Pro
Concept Pro AIR3526-IP2M Manual de usuario
Concept Pro
Concept Pro CVP5325DNIR-IP2M/2.8 Manual de usuario
Concept Pro
Concept Pro CP-HSD10-IP Manual de usuario
Concept Pro
Concept Pro CBP4304 Manual de usuario
Concept Pro
Concept Pro VCP553 Manual de usuario
Concept Pro
Concept Pro AHD Series Manual de usuario
Concept Pro
Concept Pro CVP9324-AHD Manual de usuario
Concept Pro
Concept Pro VHSD-810EXT Manual de usuario
Concept Pro
Concept Pro CBP6314DNIR Manual de usuario
Concept Pro
Concept Pro CP-HSD20-IP Manual de usuario
Concept Pro
Concept Pro CBP360-IP12M Manual de usuario
