Clarke Devil 370B Series Manual de instalación y operación

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0717 - ISSUE 1

DEVIL HALOGEN HEATERS

MODEL NO: 370PB,370SPB,371PB,& 371SPB

PART NO: 6926006, 6926001, 6926011, & 6926016

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this Clarke Quartz Halogen Infra-red Heater.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. This heater is for indoor use only.

2. Do not expose the heater or power cable to rain or wet conditions. Any

water entering the heater will increase the risk of electric shock. DO NOT

use this heater in a bathroom, shower room or any other wet environment.

3. Do not place the heater closer than 1 metre from any combustible

materials such as curtains, furniture etc.

4. Do not place the heater close to an adjacent wall or low ceiling. Allow a

distance of at least 1 metre from a wall or ceiling. Avoid placing the heater

directly below any power socket outlets.

5. Make sure that the wire guard is not covered.

6. Do not operate the heater in an explosive atmosphere such as in the

presence of flammable gases, dust or vapours, such as in a paint spray

booth or any explosive environment.

7. Never stand the heater on a vehicle where it could tip over.

8. Do not allow the halogen tubes to become covered with dust which could

become a fire hazard. If used in a dusty workplace the heater should be

cleaned as described under Cleaning and Maintenance.

9. Do not touch the halogen tubes for at least 15 minutes after switching off.

10. Do not leave the heater unattended.

11. If children are present always use with a fireguard.

12. Store the heater out of the reach of children and do not allow any person

unfamiliar with these instructions to operate it.

13. Do not use this heater with a programmable timer used to switch it on

automatically.

14. Only use in an upright position. The tilt safety switch should operate if the

heater tips over.

15. Always move the heater using the handles provided and avoid trapping

the fingers between the handle and the heater body.

ELECTRICAL SAFETY

1. Electrical appliances must match the power outlet. Never modify the plug

in any way. Do not use adaptor plugs with earthed (grounded) appliances.

Correct plugs and outlets will reduce the risk of electric shock.

2. Do not abuse the electrical cable. Never use the cable for pulling or

unplugging the heater. Keep the cable away from sources of heat, oil,

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

sharp edges or moving parts. Damaged or tangled cables increase the risk

of electric shock.

3. Keep the mains cable well away from any machinery and ensure an

adequate electrical supply is close at hand so that the operation is not

restricted by the length of the cable.

4. ALWAYS disconnect from the mains supply before moving the heater, or

performing any cleaning or maintenance tasks.

5. Inspect the mains cable regularly for signs of damage. DO NOT use if it is

damaged, and ALWAYS keep it away from the source of heat.

6. Check the heater for damage before use. DO NOT use if the halogen

tubes are damaged or broken. Any damage should be properly repaired

or the part replaced. If in doubt, DO NOT use. Consult your local Clarke

dealer.

SERVICE & REPAIRS

1. If necessary, have your heater repaired by a qualified person using

identical replacement parts. This will ensure that the safety of the

appliance is maintained.

ELECTRICAL CONNECTIONS

DEVIL 370PB & 370SPB 230VOLT HEATER UNITS

The 370 models are provided with a 13 amp BS 1363 plug, fitted with a 13amp

fuse and MUST be connected to a standard, 230 Volt (50Hz) electrical supply,

preferably through a suitably fused isolator switch.

IMPORTANT: The wires in the mains lead should be wired up in accordance

with the following colour code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the flexible cable of this appliance may not correspond with

the coloured markings identifying terminals in your plug, proceed as follows:

WARNING: THIS APPLIANCE MUST BE EARTHED

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Connect the GREEN & YELLOW coloured wire to the plug

terminal marked with a letter E or Earth symbol.

• or coloured GREEN or GREEN & YELLOW.

• Connect the BROWN coloured wire to the plug terminal marked a

letter “L” or coloured RED

• Connect the BLUE coloured wire to the plug terminal marked a letter

“N” or coloured BLACK.

If this appliance is found to be fitted with a plug which is moulded on to the

electric cable (i.e. non-rewireable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the

correct replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local Clarke dealer.

FUSE RATING

The fuse in the plug must be replaced with one of the same rating and this

replacement must be ASTA approved to BS1362.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

DEVIL 371PB & 371SPB 110VOLT HEATER UNITS

The 371 models MUST be connected to a 110 Volt, 1 phase 50Hz supply through

a suitably fused isolator switch. ON NO ACCOUNT MUST A 230V, 13AMP

(BS1363) PLUG BE USED.

NOTE: If a portable 110V transformer is used, make sure it has a rated

capacity sufficient to take the load of the heater.

In the event that the heater is hard wired into the electrical system, it must be

carried out in accordance with IEE regulations.

Any power supply provided by the user must be comparable with the power

cable supplied with the heater, and any additional cables should not be

allowed to cause a trip hazard.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING AND ASSEMBLY

Before assembling, please check contents against the following list and advise

your dealer immediately if any parts are missing.

TOOLS REQUIRED

10mm & 14 mm spanner (370PB/371PB),

10 mm spanner (370SPB/371SPB).

DEVIL 370PB /371PB

1. Attach the support bars to the heater

body using 14mm securing bolts supplied.

2. Attach the handle to the heater body

using four bolts and plastic blocks

supplied.

3. Unscrew the front guard and fit the

halogen tubes (see page 7).

DEVIL 370SPB/371SPB

1. Bolt the three parts of the frame together

at positions 1 & 2.

2. Attach the frame to the heater body as

shown, using the locking knobs and the

plastic packing pieces at positions 3 & 4.

NOTE: The larger packing piece should fit

nearer the heater.

3. Unscrew the front guard and fit the

halogen tubes (see page 7).

1 x Heater 2 x Quartz Halogen Tubes

2 x Support Bars with casters (P only) 1x Frame with casters (SP only)

2 x Locking Knobs (SP only) 2 x Packing Pieces (SP only)

1 x Handle 1 x Fixings pack

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. Place the heater where needed and lock the braked caster(s) to prevent it

from moving. When moving the heater use the handles.

2. Slacken the locking knobs and rotate the heater body to the required

angle. Tighten the knobs on each side to lock into place (SP models only).

3. Connect the mains cable to a suitable power supply.

4. Use the on/off switches to turn on either one, or both halogen tubes.

IMPORTANT: When using the SP model heaters, avoid tilting the heater

downwards even though the tilt safety switch may cut in to prevent

overheating of both the heater and the floor.

CLEANING & MAINTENANCE

If the heater has been in use always disconnect it from the power supply and

let it cool down for at least 15 minutes before performing any cleaning or

maintenance tasks.

PERIODICALLY

• If there is a build up of dirt, wipe thoroughly with a damp cloth. Take

care that no moisture enters the heater. Take care NOT to touch the

halogen tubes with your fingers.

• Check the mains cable for damage. Heat will cause the cable to

stiffen and crack. If this is found, have the cable replaced. Check

cable routing and ensure it is well away from the heat source.

• Ensure halogen tubes are free of dust (use compressed air to clean if

possible. (ALWAYS wear a dust mask if performing this operation)

• Refer to your Clarke dealer if internal maintenance is required.

• When storing the heater, let it cool down, then keep it in a dry,

ventilated place.

FITTING/ REPLACING QUARTZ HALOGEN TUBES

Before attempting to fit/replace halogen tubes, ensure the heater is switched

off and isolated from the electrical supply.

Never hold the halogen tubes with bare hands. Always handle using either a

soft clean glove or a piece of soft clean cloth wrapped around the tube.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

1. Remove the two pozidrive screws securing the wire guard, remove the

guard and store removed parts safely.

2. To remove the halogen tube, grasp and gently but firmly push it to one end

of the heater. The tube holders are spring loaded which will allow the tube

sufficient movement to clear the opposite holder.

3. Remove the halogen tube and dispose of it according to local regulations.

4. Fit new halogen tubes in reverse order, repeat the procedure for the

second tube.

5. Replace the guard using the screws removed earlier.

The heater is now ready for use.

FAULT FINDING

SYMPTOM PROBLEM SOLUTION

Heater does not

operate, although

plugged in and

switched on.

Plug is loose/bad

connection.

Remove the plug & check

the connection of the plug

and socket.

Fuse blown. Replace if necessary and

investigate the cause. If

fuse blow repeatedly,

consult your Clarke dealer.

No power at socket

outlet.

Insert plug into a suitable

socket.

Tilt safety switch is

disabling unit.

Ensure unit is upright. If

switch does not re-set,

consult your Clarke dealer.

Halogen tube is glow-

ing hot.

Input voltage incorrect. Ensure power supply

matches the rating on the

label.

Air inlet partly blocked. Ensure the heater is kept

away from any objects or

materials which could

partially cover the guard or

be drawn onto it.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description

1Caster(standard)

2CasterwithBrake

3CeramicEndCap

4QuartzHalogenTube

5ON/OFFSwitch

6PowerCable

7 Wire Guard

8 Frame (SP only)

9 Plastic Handle (SP only)

10 Securing Knob (SP only)

11 Plastic Saddle (SP only)

12 Support Bar (P only)

13 Securing Bolt (P only)

14 Tilt Safety Switch

15 Rear Handle (P only)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

Please note that the details and specifications contained herein are correct at

the time of going to print. However CLARKE International reserve the right to

change specifications at any time without prior notice. Always consult the

machine’s data plate.

Model Number Devil

370PB

Devil

370SPB

Devil

371PB

Devil

371SPB

Model Number 6926001 6926006 6926011 6926006

Weight 16.6 kg 16 kg 13.8 kg 14.4 kg

Dimensions (L x W x H) 490 x 563 x

887 mm

490 x 563 x

887 mm

610 x 626 x

788 mm

610 x 626 x

788 mm

Wattage 3 kW 3 kW 3 kW 3 kW

Amperage 13 A 13 A 27.5 A 27.5 A

Supply Voltage 230V/50 hz 230V/50 hz 110V/50hZ 110V/50hZ

Fuse Rating 13 A 32 A n/a n/a

Insulation Class IP20 IP20 IP20 IP20

Max Heat Output 3 kW 3 kW 3 kW 3 kW

Quartz Tube Rating 2 x 1.5kW

@230V

2 x 1.5kW

@110V

2 x 1.5kW

@230V

2 x 1.5kW

@110V

Plug type BS1363 EN60309 BS1363 EN60309

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Clarke

Clarke

Clarke DEVIL 371PC Manual de instalación y operación

Clarke

Clarke DEVIL 370SPC Manual de instalación y operación

Clarke

Clarke DEVIL 350 230V Manual de instalación y operación

Clarke

Clarke Devil 355MD Instrucciones de funcionamiento

Clarke

Clarke OFR 9/90 Manual de instrucciones

Clarke

Clarke OFR 9 Manual de instrucciones

Clarke

Clarke OFR 5/50 Manual de instrucciones

Clarke

Clarke IQ2000S Manual de lista de piezas

Clarke

Clarke XR60 Manual de instalación y operación

Clarke

Clarke DEVIL 371SPC Manual de instalación y operación

Clarke

Clarke GH1 Manual de usuario

Clarke

Clarke DEVIL155 Manual

Clarke

Clarke 6933980 Manual de instrucciones

Clarke

Clarke DEVIL 7003 Manual de instrucciones

Clarke

Clarke OFR 9 Manual de instrucciones

Clarke

Clarke XR75 Manual de instalación y operación

Clarke

Clarke DEVIL 5000PTC Manual de instrucciones

Clarke

Clarke DEVIL 2000PTC-B Manual de instrucciones

Clarke

Clarke DEVIL 9000PTC Manual de instrucciones

Clarke

Clarke DEVIL 2800PTC-B Manual de instrucciones

Clarke

Clarke IRD20 Manual de instrucciones

Clarke

Clarke DEVIL 7030 Manual de instrucciones

Clarke

Clarke DEVIL 9000PTC Manual de instrucciones

Clarke

Clarke Devil 6002 Manual

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario

iLO

iLO IHP2424 Manual de funcionamiento