Cisco Meraki MR12 Manual de usuario

Assigning Static IP Addresses to an MR12 or MR58

The MR12 and MR58 wireless access points have two Ethernet ports that can be used to connect the device to a wired network. However, a static IP can only

be set on the primary Ethernet interface.

This article will discuss:

• Identifying the primary Ethernet port

• Behavior differences between primary and secondary ports

• Determining which port is being used

•Assigning a static IP

Identifying the Primary Ethernet Port

MR12

The primary Ethernet port is directly adjacent to the power connector and is labeled as Uplink.

MR58

The primary Ethernet port is located on the bottom-left side of the AP and is labeled as ETH0.

Behavior differences between primary and secondary ports

Primary (Ethernet 0)

This interface is capable of receiving power using PoE and can be assigned a static IP address. It is also capable of 10/100/1000Mbps speeds. It is intended for

connecting the MR12 to the rest of the network.

Secondary (Ethernet 1)

This interface can only receive an IP from DHCP and is not able to receive power using PoE. It is only capable of 10/100 speeds. It is still able to connect to the

Meraki Cloud Controller if the Primary connection is down, but is intended for used by a wired client. To allow use by a wired client, please refer to our

documentation regarding Extending the LAN with a Wireless Mesh Link.

Determining which port is being used

The simplest way to determine which port is being used is to physically look at the device, and refer to the diagrams above. If you are not near the device, the

easiest way to determine if the secondary port is being used is by looking at the AP Dashboard. Navigate to Monitor > Access points and click the AP in

question. Look under Status for LAN IP #. If the # = 1, then the AP is connected using the primary port. If # = 2, then the AP is connected using its secondary

port.

Assigning a static IP

A static IP can be assigned to the AP's primary interface in two ways.

Dashboard

1. In Dashboard, go to Monitor > Access points and select the AP in question.

2. Click the Edit icon.

3. On the page that appears, next to IP type select Static IP.

4. Enter the appropriate settings and click Save.

Local web interface

Refer to the MR Quick Start Guide for instructions on how to set the IP address using the local web interface.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Aironet 1600 Series Guía de referencia rápida

Cisco

Cisco AIR-CAP3502I-A-K9 Manual de usuario

Cisco

Cisco AIR-AP1832I K9C Series Manual de usuario

Cisco

Cisco Aironet 1520 Series Manual de usuario

Cisco

Cisco WAP121 Manual de usuario

Cisco

Cisco Linksys WAP55AG Manual de usuario

Cisco

Cisco AIR-AP1120B-A-K9 - Aironet 1100 Series Access... Manual

Cisco

Cisco Aironet 1850 Series Guía de referencia rápida

Cisco

Cisco Catalyst 9166I Series Manual de usuario

Cisco

Cisco Wap581 Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Cisco

Cisco Catalyst IW6300 Series Manual de usuario

Cisco

Cisco GR10-HW-EU Manual de usuario

Cisco

Cisco WAP371 Manual de usuario

Cisco

Cisco Cisco Aironet Wireless LAN Client Manual de usuario

Cisco

Cisco Meraki MR20 Manual de usuario

Cisco

Cisco Aironet 1800i Manual de usuario

Cisco

Cisco Aironet 1240AG Series Manual

Cisco

Cisco Small Business Pro Manual de usuario

Cisco

Cisco WAP131 Manual de instrucciones

Cisco

Cisco Aironet 1300 Series Manual

Cisco

Cisco Catalyst Wireless 9166D1 Manual

Cisco

Cisco WAP351 Guía

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario