Cisco WAP121 Manual de usuario

●

●

●

●

●

●

●

●

●

●

●

●

Reboot and Reset the Wireless Access Point

to Factory Default Settings

Objective

Rebooting or restarting the Wireless Access Point (WAP) deletes the logs stored in the

volatile memory. This process is performed when certain changes in the settings need a

reboot or if the WAP is not responding or booting up properly. Resetting the WAP to factory

default settings, on the other hand, erases all configurations that have been set by the user,

and restores the device to its original settings. A reset is recommended if most of the WAP

settings need to be reconfigured.

This article aims to show you how to reboot and reset your WAP to factory default settings.

Applicable Devices

WAP100 Series

WAP300 Series

WAP500 Series

Software Version

1.0.6.5 - WAP121, WAP321

1.0.2.8 - WAP131, WAP351

1.0.1.7 - WAP150, WAP361

1.3.0.3 - WAP371

1.2.1.3 - WAP551, WAP561

1.0.0.17 - WAP571, WAP571E

Reboot the Wireless Access Point

There are two ways to reboot the WAP:

Hardware reboot

Reboot through the web-based utility

Note: Images may vary depending on the exact model of your WAP. The images below are

taken from the WAP321.

Hardware Reboot

You have two ways to reboot the device hardware:

Turn the device off by pressing the POWER button while the device is connected to the

power outlet.

Note: The POWER button only works if the device is using a power adapter. If power is

supplied through Power over Ethernet (PoE), unplug your Ethernet connection for three

●

seconds then plug it back.

Press the Reset button for about three seconds only, or until the lights go off.

Reboot through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot button.

Step 3. Click OK in the confirmation window.

●

●

You should now have rebooted your device.

Reset to Factory Default Settings

There are two ways to reset the WAP to factory default settings:

Hardware reset

Reset through the web-based utility

Hardware Reset

Step 1. Press the Reset button for more than 10 seconds until the lights go off.

Step 2. Release the Reset button when the lights turn back on.

Reset through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot To Factory Default button.

Step 3. Click OK in the confirmation window.

You should now have reset your device to factory default settings.

Otros manuales para WAP121

9

Este manual sirve para los siguientes modelos

13

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Catalyst IW9165E Manual de usuario

Cisco

Cisco WAP571E Manual de usuario

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de usuario

Cisco

Cisco AIR-LAP1242AG-A-K9 Manual de usuario

Cisco

Cisco WAP121 Manual de instrucciones

Cisco

Cisco Meraki MR42 Manual de usuario

Cisco

Cisco WAP571 Manual de instrucciones

Cisco

Cisco GR10-HW-EU Manual de usuario

Cisco

Cisco Aironet 1850 Series Manual de usuario

Cisco

Cisco 1522AG - Aironet Lightweight Outdoor Mesh Access... Manual de usuario

Cisco

Cisco Aironet 3500 Series Manual de usuario

Cisco

Cisco Aironet 2600 Series Manual de usuario

Cisco

Cisco IW3702 Manual de usuario

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Manual de instrucciones

Cisco

Cisco CW91641-A Manual

Cisco

Cisco Aironet 1540 Series Manual

Cisco

Cisco Small Business AP541N Manual de usuario

Cisco

Cisco MERAKI MR44 Manual de usuario

Cisco

Cisco Meraki MR56 Manual de usuario

Cisco

Cisco Catalyst 9124AX Series Manual

Cisco

Cisco Meraki MR55 Manual de usuario

Cisco

Cisco WAP361 Manual de usuario

Cisco

Cisco WAP131 Manual de usuario

Cisco

Cisco Meraki MR52 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario