Cisco WAP351 Guía

Otros manuales para WAP351

1

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco MERAKI MR72 Manual de usuario

Cisco

Cisco Meraki MR20 Manual de usuario

Cisco

Cisco AIR-MP20B Manual de usuario

Cisco

Cisco WUMC710 Manual de usuario

Cisco

Cisco WAP300N Manual de usuario

Cisco

Cisco Meraki MR78 Manual de usuario

Cisco

Cisco Meraki MR46 Manual de usuario

Cisco

Cisco WAP121 Manual de instrucciones

Cisco

Cisco aironet 2800 series Guía de referencia rápida

Cisco

Cisco MERAKI MR46E-HW Manual

Cisco

Cisco AIR-CAP3502I-A-K9 Manual de usuario

Cisco

Cisco WAP121 Manual de usuario

Cisco

Cisco MERAKI MR66 Manual de usuario

Cisco

Cisco aironet 1522 Guía

Cisco

Cisco Meraki Go GR10 Manual de usuario

Cisco

Cisco 1552S Manual de usuario

Cisco

Cisco Catalyst IW9167E Manual

Cisco

Cisco Linksys WAP610N Manual de usuario

Cisco

Cisco Catalyst Wireless 9163E Manual de usuario

Cisco

Cisco Aironet 1600 Series Guía de referencia rápida

Cisco

Cisco Meraki CW9163E Manual de usuario

Cisco

Cisco Aironet 700W Series Manual de usuario

Cisco

Cisco WAP571 Manual de usuario

Cisco

Cisco WAP371 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

Reboot and Reset Factory Default Settings on

the WAP351

Objective

Rebooting a device is used to shut down and restart the device with a saved configuration.

The factory default is used to restore the factory default configuration on the device to

remove any previous configurations.

The objective of this document is to show you how to reboot your WAP351 device and reset

it to the factory default.

Applicable Devices

• WAP351

Software Version

• 1.0.0.39

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press and hold the Reset button located at the back of the device for approximately

ten seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log into the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the Power button to turn off the device. After 10 seconds have passed, press

the Power button a second time to power the device back on.

The Access Point reboots.

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login Page appears. Login with the saved administration credentials.