Cisco WAP371 Manual de usuario

Otros manuales para WAP371

3

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco MR18 Manual de usuario

Cisco

Cisco Aironet 521 Manual de usuario

Cisco

Cisco AIR-LAP1242AG-A-K9 Manual de usuario

Cisco

Cisco Aironet 3500 Series Manual de usuario

Cisco

Cisco Linksys WAP55AG Manual de usuario

Cisco

Cisco Linksys WAP54GX Instrucciones de funcionamiento originales

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Manual de usuario

Cisco

Cisco Meraki MR52 Manual

Cisco

Cisco Aironet 1200 Series Manual de usuario

Cisco

Cisco Aironet LAP1522 Manual

Cisco

Cisco WAP351 Guía

Cisco

Cisco Meraki MR53E Manual de usuario

Cisco

Cisco AP541N-A-K9 Manual de instrucciones

Cisco

Cisco Aironet 1810W Series Manual de usuario

Cisco

Cisco Aironet 1260 Series Manual de usuario

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Manual de usuario

Cisco

Cisco 1232AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Meraki Go GR10 Manual de usuario

Cisco

Cisco IW3702 Manual de usuario

Cisco

Cisco Aironet 2802E Manual de usuario

Cisco

Cisco Catalyst Wireless 9162I Series Manual

Cisco

Cisco Meraki GR10 Manual de usuario

Cisco

Cisco Aironet 3502P Manual de usuario

Cisco

Cisco USC 3330 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

Reboot and Reset Factory Default Settings on

the WAP371

Objective

The factory default reset erases all configuration settings that have been modified by the

user, and restores the device to its original settings. This may be helpful if you lose the

password to a device and wish to regain access.

Note: It is advised to save a backup copy of the configuration before beginning this process.

Refer to Download/Backup Configuration on the WAP 371 for additional information.

Performing a reboot restarts the device with a saved configuration.

The objective of this article is to show you how to reset to factory default settings and how to

reboot a WAP371 Wireless Access Point.

Applicable Devices

• WAP371

Software Version

• 1.0.1.5

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press the Reset button for approximately ten seconds with a pin located at the back

of the device.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log in into the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the power button to turn off the device. After 10 seconds have passed, press

the power button a second time to power the device back on.

The Access Point reboots and is refreshed.

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login Page appears. Login with the saved administration credentials.