Cisco SGACL Manual de usuario
CHAPTER
5-1
Cisco TrustSec Switch Configuration Guide
OL-22192-02
5
Configuring SGACL Policies
Revised: August 15, 2013, OL-22192-02
This section includes the following topics:
•Cisco TrustSec SGACL Feature Histories, page 5-1
•SGACL Policy Configuration Process, page 5-2
•Enabling SGACL Policy Enforcement Globally, page 5-2
•Enabling SGACL Policy Enforcement Per Interface, page 5-3
•Enabling SGACL Policy Enforcement on VLANs, page 5-3
•Manually Configuring SGACL Policies, page 5-4
•Displaying SGACL Policies, page 5-6
•Refreshing the Downloaded SGACL Policies, page 5-7
Cisco TrustSec SGACL Feature Histories
For a list of supported TrustSec features per platform and the minimum required IOS release, see
the Cisco TrustSec Platform Support Matrix at the following URL:
http://www.cisco.com/en/US/solutions/ns170/ns896/ns1051/trustsec_matrix.html
Otherwise, see product release notes for detailed feature introduction information.
5-2
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
SGACL Policy Configuration Process
SGACL Policy Configuration Process
Follow these steps to configure and enable Cisco TrustSec SGACL policies:
Step 1 Configuration of SGACL policies should be done primarily through the Policy Management function of
the Cisco Secure ACS or the Cisco Identity Services Engine (see the Configuration Guide for the Cisco
Secure ACS or the Cisco Identity Services Engine User Guide).
If you are not using AAA on a Cisco Secure ACS or a Cisco ISE to download the SGACL policy
configuration, you can manually configure the SGACL mapping and policies (see the “Manually
Configuring SGACL Policies” section on page 5-4 and the “Manually Configuring SGACL Policies”
section on page 5-4).
Note An SGACL policy downloaded dynamically from the Cisco Secure ACS or a Cisco ISE will
override any conflicting locally-defined policy.
Step 2 To enable SGACL policy enforcement on egress traffic on routed ports, enable SGACL policy
enforcement globally as described in the “Enabling SGACL Policy Enforcement Globally” section on
page 5-2.
Step 3 To enable SGACL policy enforcement on switched traffic within a VLAN, or on traffic that is forwarded
to an SVI associated with a VLAN, enable SGACL policy enforcement for specific VLANs as described
in the “Enabling SGACL Policy Enforcement on VLANs” section on page 5-3.
Enabling SGACL Policy Enforcement Globally
You must enable SGACL policy enforcement globally for Cisco TrustSec-enabled routed interfaces.
To enable SGACL policy enforcement on routed interfaces, perform this task:
Configuration Examples for Enabling SGACL Policy Enforcement Globally
Catalyst 6500, Catalyst 3850:
Switch(config)# cts role-based enforcement
Command Purpose
Step 1 Router# configure terminal Enters global configuration mode.
Step 2 Router(config)# cts role-based
enforcement
Enables Cisco TrustSec SGACL policy enforcement
on routed interfaces.
5-3
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Enabling SGACL Policy Enforcement Per Interface
Enabling SGACL Policy Enforcement Per Interface
You must first enable SGACL policy enforcement globally for Cisco TrustSec-enabled routed interfaces.
This feature is not supported on Port Channel interfaces.
To enable SGACL policy enforcement on Layer 3 interfaces, perform this task:
Detailed Steps Catalyst 6500
Configuration Examples for Enabling SGACL Policy Enforcement Per Interface
Catalyst 3850:
Switch# configure terminal
Switch(config)# interface gigabit 1/0/2
Switch(config-if)# cts role-based enforcement
Switch(config-if)# end
Enabling SGACL Policy Enforcement on VLANs
You must enable SGACL policy enforcement on specific VLANs to apply access control to switched
traffic within a VLAN, or to traffic that is forwarded to an SVI associated with a VLAN.
To enable SGACL policy enforcement on a VLAN or a VLAN list, perform this task:
Detailed Steps Catalyst 6500
Configuration Examples for Enabling SGACL Policy Enforcement on VLANs
Catalyst 3850:
Switch# configure terminal
Switch(config)# cts role-based enforcement vlan-list 31-35,41
Switch(config)# exit
Command Purpose
Step 1 Router# configure terminal Enters global configuration mode.
Step 2 Router(config)# interface gigabit 6/2 Specifies interface on which to enable or
disable SGACL enforcement.
Step 3 Router(config-if)# cts role-based enforcement Enables Cisco TrustSec SGACL policy
enforcement on routed interfaces.
Step 4 Router(config-if)# do show cts interface Verifies that SGACL enforcement is enabled.
Command Purpose
Step 1 Router# configure terminal Enters global configuration mode.
Step 2 Router(config)# cts role-based
enforcement vlan-list vlan-list
Enables Cisco TrustSec SGACL policy enforcement
on the VLAN or VLAN list.
5-4
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Manually Configuring SGACL Policies
Manually Configuring SGACL Policies
A role-based access control list bound to a range of SGTs and DGTs forms an SGACL, a TrustSec policy
enforced on egress traffic. Configuration of SGACL policies are best done through the policy
management functions of the Cisco ISE or the Cisco Secure ACS. To manually (that is, locally)
configure SGACL policies, do the following:
1. Configure a role-based ACL.
2. Bind the role-based ACL to a range of SGTs.
Note An SGACL policy downloaded dynamically from the Cisco ISE or Cisco ACS overrides any conflicting
manually configured policy.
Manually Configuring and Applying IPv4 SGACL Policies
Detailed Steps for Catalyst 3850
Command Purpose
Step 1 Router# configure terminal Enters global configuration mode.
Step 2 ip access-list role-based rbacl-name
Example:
Switch(config)# ip access-list
role-based allow_webtraff
Creates a Role-based ACL and enters Role-based ACL
configuration mode.
Step 3 {[sequence-number] | default | permit |
deny | remark}
Example:
Switch(config-rb-acl)#10 permit tcp dst
eq 80 dst eq 20
Specifies the access control entries (ACEs) for the
RBACL.
You can use most of the commands and options
allowed in extended named access list configuration
mode, with the source and destination fields omitted.
Press Enter to complete an ACE and begin the next.
For full explanations of ACL configuration, keywords,
and options, see, Security Configuration Guide:
Access Control Lists, Cisco IOS XE Release 3S.
The following ACE commands or keywords are not
supported:
•reflect
•evaluate
•time-range
Step 4 Switch(config-rb-acl)# exit Exits to global configuration mode.
5-5
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Manually Configuring SGACL Policies
Configuration Examples for Manually Configuring SGACL Policies
Catalyst 3850 IPv4 Manual SGACL policy:
Switch(config)# ip access role allow_webtraff
Switch(config-rb-acl)# 10 permit tcp dst eq 80
Switch(config-rb-acl)# 20 permit tcp dst eq 443
Switch(config-rb-acl)# 30 permit icmp
Switch(config-rb-acl)# 40 deny ip
Switch(config-rb-acl)# exit
Switch(config)# cts role-based permissions from 55 to 66 allow_webtraff
Switch# show ip access allow_webtraff
Role-based IP access list allow_webtraff
10 permit tcp dst eq www
20 permit tcp dst eq 443
30 permit icmp
40 deny ip
Switch# show show cts role-based permissions from 50 to 70
XXX need output XX
Step 5 [no] cts role-based permissions {default
|[from {sgt_num | unknown} to {dgt_num |
unknown}]{rbacls | ipv4 rbacls}
Example:
Switch(config)# cts role-based
permissions from 55 to 66 allow_webtraff
Binds SGTs and DGTs to the RBACL. The
configuration is analogous to populating the
permission matrix configured on the Cisco ISE or the
Cisco Secure ACS.
•Default—Default permissions list
•sgt_num—0 to 65,519. Source Group Tag
•dgt_num—0 to 65,519. Destination Group Tag
•unknown—SGACL applies to packets where the
security group (source or destination) cannot be
determined.
•ipv4—Indicates the following RBACL is IPv4.
•rbacls—Name of RBACLs
Step 6 Switch(config)# end Exits to Privileged Exec mode.
Step 7 Switch# show cts role-based permissions Displays permission to RBACL configurations.
Step 8 Switch# show ip access-lists
allow_webtraff
Displays ACEs of all RBACLs or a specified RBACL.
Command Purpose
5-6
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Displaying SGACL Policies
Displaying SGACL Policies
After configuring the Cisco TrustSec device credentials and AAA, you can verify the Cisco TrustSec
SGACL policies downloaded from the authentication server or configured manually. Cisco TrustSec
downloads the SGACL policies when it learns of a new SGT through authentication and authorization
on an interface, from SXP, or from manual IP address to SGT mapping.
To display the contents of the SGACL policies permissions matrix, perform this task:
Detailed Steps for Catalyst 6500
Using the keywords, you can display all or part of the permissions matrix:
•If the from keyword is omitted, a column from the permissions matrix is displayed.
•If the to keyword is omitted, a row from the permissions matrix is displayed.
•If the from and to keywords are omitted, the entire permissions matrix is displayed.
•If the from and to keywords are specified, a single cell from the permissions matrix is displayed and
the details keyword is available. When details is entered, the ACEs of the SGACL of the single cell
are displayed.
This example shows how to display the content of the SGACL policies permissions matrix for traffic
sourced from security group 3:
Router# show cts role-based permissions from 3
Role-based permissions from group 3 to group 5:
SRB3
SRB5
Role-based permissions from group 3 to group 7:
SRB4
Command Purpose
Step 1 Router# show cts role-based permissions
default [ipv4 | ipv6 | details]
Displays the list of SGACL of the default policy.
Router# show cts role-based permissions
[from {source-sgt | unknown}] [to {dest-sg
| unknown}] [ipv4 | ipv6] [details]
Displays the contents of the permissions matrix,
including SGACLs downloaded from the
authentication server and manually configured on
the switch.
5-7
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Refreshing the Downloaded SGACL Policies
Refreshing the Downloaded SGACL Policies
Detailed Steps for Catalyst 6500, Catalyst 3850, Catalyst 3650
Command Purpose
Step 1 cts refresh policy {peer [peer-id]
| sgt [sgt_number|
default|unknown]}
Switch3850# cts refresh policy
peer my_cisco_ise
Performs an immediate refresh of the SGACL policies from
the authentication server.
•If a peer-id is specified, only the policies related to the
specified peer connection are refreshed. To refresh all
peer policies, press Enter without specifying an ID.
•If an SGT number is specified, only the policies related
to that SGT are refreshed. To refresh all security group
tag policies, press Enter without specifying an SGT
number. Select default to refresh the default policy.
Select unknown to refresh unknown policy.
5-8
Cisco TrustSec Switch Configuration Guide
OL-22192-02
Chapter 5 Configuring SGACL Policies
Refreshing the Downloaded SGACL Policies
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Software de Cisco
Cisco
Cisco CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT... Manual de servicio
Cisco
Cisco CRS-1 Series Manual de usuario
Cisco
Cisco Signaling Interface H.323 Manual de usuario
Cisco
Cisco XO Manual de usuario
Cisco
Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... Manual de usuario
Cisco
Cisco Router IOS XR Manual de usuario
Cisco
Cisco DVD-ROM Manual de instalación y operación
Cisco
Cisco OL-10426-01 Manual de usuario
Cisco
Cisco 2600 Series Cómo utilizar
Cisco
Cisco OL-4015-08 Manual de usuario
Cisco
Cisco Router IOS XR Manual de usuario
Cisco
Cisco 3.3 Manual de usuario
Cisco
Cisco IPS-4240-K9 - Intrusion Protection Sys 4240 Manual de usuario
Cisco
Cisco CISCO1811 Manual de usuario
Cisco
Cisco Unity Express 8.0 Voice-Mail System Manual de usuario
Cisco
Cisco TELEPRESENCE MANAGEMENT SUITE EXTENSION - FOR IBM LOTUS NOTES... Manual de usuario
Cisco
Cisco ACTIVE NETWORK ABSTRACTION - BROCHURE WHATS NEW IN RELEASE... Manual de usuario
Cisco
Cisco CONFERENCING EXTENSIONS - FOR MICROSOFT EXCHANGE... Manual de usuario
Cisco
Cisco 4700M Manual de instrucciones
Cisco
Cisco PVDM2 24DM - Digital Modem Module Manual de usuario
Manuales populares de Software de otras marcas
PS Audio
PS Audio PowerPlay Manual del propietario
Brady
Brady LOCKOUT PRO 3.0 Manual de servicio
Avaya
Avaya Interaction Center Manual de usuario
Texas Instruments
Texas Instruments TI-83 Plus Silver Edition Manual
Novell
Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario
Oracle
Oracle Application 9i Manual de usuario
Acer
Acer RDM Manual de usuario
Canon
Canon Vixia HF21 Manual de usuario
Canon
Canon ZR950 Manual de usuario
Samsung
Samsung Auto Backup Manual de usuario
Polycom
Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento
Brocade Communications Systems
Brocade Communications Systems Brocade 8/12c Manual de usuario