Burkert 6407 Manual de usuario
Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 6407
2/2-way solenoid valve
2/2-Wege-Magnetventil
Électrovanne 2/2 voies
2
1 OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶Read the operating instructions carefully and follow the safety
instructions in particular, and also observe the operating conditions.
▶Operating instructions must be available to each user.
▶The liability and warranty for the device are void if the operating
instructions are not followed.
1.1 Symbols
▶Designates an instruction to prevent risks.
→Designates a procedure which you must carry out.
Warning of injuries:
DANGER!
Imminent danger! Serious or fatal injuries.
WARNING!
Potential danger! Serious or fatal injuries.
CAUTION!
Danger! Minor or moderately severe injuries.
Warns of damage to property:
NOTE!
Contents
1 Operating instructions.................................................................. 2
2 Intended use ............................................................................... 3
3 Basic safety instructions .............................................................. 4
4 Technical data ............................................................................. 5
5 Installation ................................................................................... 8
6 Maintenance, troubleshooting ................................................... 10
7 Spare parts ............................................................................... 12
8 Transport, storage, disposal....................................................... 13
english
3
2.1 Denition of therm “device”
In these operating instructions, the term “device” always refers to
the solenoid valve Type 6407.
2 INTENDED USE
Incorrect use of the solenoid valve Type 6407 can be dangerous
to people, nearby equipment and the environment.
▶The device is designed to control, shut o and meter neutral media
up to a viscosity of 21mm2/s.
▶In areas at risk of explosion, only use devices approved for use in
those areas. These devices are labeled with a separate Ex type label.
For use in areas at risk of explosion, note the information provided
on the separate Ex type label and the separate explosion-related
operating instructions included in the scope of supply.
▶Provided the cable plug is connected and installed correctly, the
device satises protection class IP65 in accordance with DIN EN
60529 / IEC 60529.
▶Use according to the permitted data, operating conditions and
conditions of use specied in the contract documents and operat-
ing instructions.
▶Correct transportation, correct storage and installation and careful
use and maintenance are essential for reliable and problem-free
operation.
▶Use the device only as intended.
english
4
3 BASIC SAFETY INSTRUCTIONS
These safety instructions do not consider any contingencies or inci-
dents which occur during installation, operation and maintenance.
The operator is responsible for observing the location-specic safety
regulations, also with reference to the personnel.
Danger of high pressure.
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Risk of electric shock.
▶Before reaching into the device, switch o the power supply and
secure to prevent reactivation.
▶Observe applicable accident prevention and safety regulations for
electrical equipment.
Risk of burns/Risk of re if used continuously through hot device
surface.
▶Keep the device away from highly ammable substances and media
and do not touch with bare hands.
Risk of injury due to malfunction of valves with alternating
current (AC).
Sticking core causes coil to overheat, resulting in a malfunction.
▶Monitor process to ensure function is in perfect working order.
Risk of short-circuit/escape of media through leaking screw
joints.
▶Ensure seals are seated correctly.
▶Carefully screw valve and connection lines together.
General hazardous situations.
To prevent injury, ensure that:
▶The device may be operated only when in perfect condition and
in consideration of the operating instructions.
▶Do not make any changes and do not subject the device to
mechanical loads.
▶Secure system against unintentional activation.
▶Installation, operation and maintenance may only be performed
by qualied specialists.
▶nstall the device according to the regulations applicable in the
country.
▶After an interruption in the power supply or pneumatic supply,
ensure that the process is restarted in a dened or controlled
manner.
▶Observe the general rules of technology.
english
5
3.1 Warranty
The warranty is only valid if the device is used as intended in accor-
dance with the specied application conditions.
3.2 Information on the Internet
The operating instructions for Type 6407 can be found on the
internet at: www.burkert.com
4 TECHNICAL DATA
4.1 Operating conditions
The following values are indicated on the type label:
•Voltage (Tolerance ±10 %) / Current type
•Coil power consumption (active power in W - at operating
temperature)
•Pressure range
•Body material: Brass (MS), cast iron (GG)
•Seal material: PTFE/Graphit (EG), PTFE/FKM (EF), EPDM/
Graphit (AG)
Circuit function 2/2-way valve:
A (NC)
Protection class: IP65 in accordance with DIN EN 60529 / IEC
60529 with cable plug, e.g. Bürkert Type 2518
english
6
4.2 Conformity
The device conforms with the EU Directives according to the EU
Declaration of Conformity (if applicable).
4.3 Standards
The applied standards, which verify conformity with the EU Directives,
can be found on the EU-Type Examination Certicate and / or the EU
Declaration of Conformity (if applicable).
4.4 Application conditions
Ambient temperature: max. +45°C
max. +40 °C for ATEX/IECEx
Permitted medium temperature depending on coil material and seal
material:
Seal material Medium temperature
PTFE/Graphit -40 °C…+150 °C
EPDM/Graphit -40 °C…+135 °C
PTFE/FKM -10 °C…+120 °C
ATEX/IECEx max. 90°C
Also observe for valves with UL/UR approval:
Medium Seal material Medium
temperature
Ambient
temperature
Air,
Inertgas
PTFE/Graphit -40 °C ... +120 °C -40 °C ... +55 °C
PTFE/FKM -10 °C ... +120 °C -10 °C ... +55 °C
Water PTFE/Graphit 0 °C ... +100 °C 0 °C ... +55 °C
PTFE/FKM 0 °C ... +100 °C 0 °C ... +55 °C
Steam
(var. Code
NA07)
PTFE/Graphit 0 °C ... +150 °C 0 °C ... +45 °C
PTFE/FKM 0 °C ... +120 °C 0 °C ... +55 °C
Oil PTFE/Graphit 0 °C ... +150 °C 0 °C ... +45 °C
PTFE/FKM -10 °C ... +120 °C -10 °C ... +55 °C
Operating duration: Unless otherwise stated on the type label,
the solenoid valve is suitable for continuous
operation.
Exception: Devices with kick-and-drop
electronics: Maximum duty cycle 50% and
maximum 6 switching cycles per minute.
english
7
Important information for functional reliability during continuous
operation: If standstill for a long period at least 1-2 activations
per day are recommended.
Service life: High switching frequency and high pressures
reduce the service life
Permitted media depending on seal material:
Seal material Permitted media
PTFE/Graphit Vacuum, neutral gases and liquid media (e.g.
compressed air, water, hydraulic oil),
hot water and steam
PTFE/FKM
PTFE/EPDM Cold and warm water, oil and grease-free
media
NOTE!
If liquid media is used with high dierential pressures, water
hammer can occur.
4.5 Type label
Type
Circuit function
Nominal diameter Seal material
Body material
Order number Manufacture code
Voltage, Frequency, Power
consumption
Connection thread, Operating
pressure
6407 A 13,0 EG MS
Made in Germany
00320856
W12MN
230 V 50 Hz 16W
G1/2 P
N 0
- 10 bar
english
8
5 INSTALLATION
DANGER!
Risk of injury from high pressure and discharge of medium.
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Risk of electric shock.
▶Before reaching into the device, switch o the power supply and
secure to prevent reactivation.
▶Observe applicable accident prevention and safety regulations
for electrical equipment.
WARNING!
Risk of injury from improper installation.
▶Installation may be carried out by authorized technicians only
and with the appropriate tools.
▶Secure system from unintentional activation.
▶Following assembly, ensure a controlled restart.
5.1 Before installation
Installation position: any, actuator preferably upwards.
→Check pipelines for dirt and clean.
→Install a dirt lter before the valve inlet (≤ 500μm).
5.2 Installation
NOTE!
Caution risk of breakage.
•Do not use the coil as a lever arm.
→Hold the device using a suitable tool on the body and screw into
the pipeline.
Valve body must not be installed under tension.
Sealing material must not get into the device.
→Observe direction of ow:
The arrow on the body indicates the direction of ow.
english
9
5.3 Electrical connection of the cable plug
WARNING!
Risk of injury due to electrical shock.
▶Before reaching into the system, switch o the power supply
and secure to prevent reactivation.
▶Observe applicable accident prevention and safety regulations
for electrical equipment.
If the protective conductor is not connected, there is a risk of
electric shock.
▶Always connect protective conductor and check electrical conti-
nuity between coil and body.
→Tighten cable plug (authorized cable plug see data sheet),
observing maximal torque 1 Nm.
→Check that seal is tted correctly.
→Connect protective conductor and check electrical continuity
between coil and body.
Authorized cable plug
e.g. Type 2518 or other suitable
cable plug in accordance with
DIN EN 175301-803, Form A
Seal
max. 1 Nm
english
10
6 MAINTENANCE, TROUBLESHOOTING
DANGER!
Risk of injury from high pressure and discharge of medium.
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
WARNING!
Risk of injury from improper maintenance.
▶Maintenance may be carried out by authorized technicians only
and with the appropriate tools.
▶Secure system from unintentional activation.
▶Following maintenance, ensure a controlled restart.
6.1 Installation of the coil
WARNING!
Risk of injury due to electrical shock.
▶Before reaching into the system, switch o the power supply and
secure to prevent reactivation.
If the protective conductor contact between the coil and body is
missing or if coil incorrectly installed, there is danger of electrical shock.
▶Check protective conductor contact after installing the coil.
▶During installation ensure that the coil is situated rmly on the body
cover so that the protective conductor connection of the coil is
connected to the valve body.
WARNING!
Escaping medium.
When a sticking nut is loosened, medium may escape.
▶Do not tighten sticking nut any further.
Overheating, risk of re.
If the protective conductor contact between the coil and body is
missing, there is danger of electrical shock.
▶Check protective conductor contact after installing the coil.
→Connect coil body to the core guide pipe.
→Screw on coil with nut. Observe the tightening torques in the
following table.
→Check protective conductor.
english
Tabla de contenidos
Otros manuales de Unidad de control de Burkert
Burkert
Burkert 2300 Series Manual de usuario
Burkert
Burkert 2101 Manual de usuario
Burkert
Burkert WhisperValve 6724 Manual de usuario
Burkert
Burkert 8840 Manual de usuario
Burkert
Burkert PTB 03 ATEX 1030 X Manual de usuario
Burkert
Burkert 2000 INOX Manual de usuario
Burkert
Burkert 2106 Manual de usuario
Burkert
Burkert 8647 AirLINE SP Manual de usuario
Burkert
Burkert 3233 Manual de usuario
Burkert
Burkert 5282 Manual de usuario
Burkert
Burkert 2301 Series Manual de usuario
Burkert
Burkert 0121 Manual de usuario
Burkert
Burkert 0127 Manual de usuario
Burkert
Burkert 8691 Manual de usuario
Burkert
Burkert 6020 Manual de usuario
Burkert
Burkert 6510 Manual de usuario
Burkert
Burkert 8690 Manual de usuario
Burkert
Burkert EPS 22 ATEX 1 136 X Manual de usuario
Burkert
Burkert 2657 Manual de usuario
Burkert
Burkert 2012 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
