AWS CP4-Series Manual de usuario

CP4-100 (100g x 0.01g)

CP4-650 (650g x 0.1g)

User Manual

CP4-Series

Thank you for purchasing the American Weigh

CP4-Series digital pocket scale. Please read all operating

instructions carefully before use. Scales are precision

measuring devices and should always be handled with

proper care. To ensure years of reliable service, keep these

simple tips in mind:

• Do not exceed the scale’s maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, calibration

and adjustment may be necessary.

• Allow your scale to warm up for 30-60 seconds before

performing calibration and adjustment(if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing inaccuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Alwaysweighonaatandlevelsurface,freefrom

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

• Checkthebatteriesrstifyouarehavinganytrouble

with your scale. This simple step can remedy most

scale issues.

• Do not disassemble your scale. This product contains

no user serviceable parts.

PCS

UNITS

OFF

TARE

LIGHT

I. Part List

1. Scale

2. Cover/Expansion Tray

3. CR2032 Lithium Batteries (x2)

II. Key Description

III. Battery Installation

1. Beforeusingthescaleforthersttime,check

the battery compartment and remove any plastic

insulation strips or packaging that may be in place to

prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the

positive and negative contacts are properly aligned.

Install Negative

Side Up

Install Positive

Side Up

Negative Terminal

Postive Terminal

CR2032 (Button Cell) Battery Installation

Install Negative

Side Up

Install Positive

Side Up

Negative Terminal

Postive Terminal

CR2032 (Button Cell) Battery Installation

PCS Key

UNITS Key

TARE Key

LIGHT Key

Weight Indicator

Unit Indicator

ON/OFF Key

CP4-Series

IV. Operation

1. Placethescaleonaat,levelsurfaceandpressthe

ON/OFF key to turn the scale on.

2. Once the start-up process completes and the scale

goes to zero you are ready to weigh.

3. Place the quantity to be weighed onto the weighing

platform.

4. Wait a couple seconds for the display to stabilize

before taking a weight reading.

V. Changing the Unit of Measure

1. Press the UNITS key to change the scales displayed

unit of measure.

2. If the scale is turned off then back on, it will default

to the last unit used.

• CP4-100 Units: g (gram) oz (ounce) ct (carat)

gn (grain)

• CP4-650 Units: g (gram) oz (ounce) ozt (troy

ounce) dwt (pennyweight)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight

of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the

available capacity.

1. Place the empty container or vessel on the weighing

platform.

2. Press the TARE key once. The display will then

reset to zero. If the container is removed, it’s weight

will be displayed as a negative number.

3. Youmaynowllthecontainerwiththequantityto

be weighed. The display will show the net weight of

the contents.

4. To return to normal weight display (gross weight),

remove any items from the weighing platform and

press the TARE key again to re-zero the scale.

VII. Backlight Feature

This scale features a back-light that can be turned on or off.

The back-light is enabled by default.

1. To disable, press the LIGHT key.

2. To enable, press the LIGHT key again.

VIII. Parts Counting Feature

All object must be of uniform weight for counting to work.

1. Turn on scale as described above.

2. Place a sample quantity (25, 50, 75, or 100pcs) of

the material you want to count on the platform

3. Press and hold the PCS key for 2 seconds until a

number is displayed (ie. 100pcs).

4. Press UNITS to change the sample quantity to

match the number you have on the platform.

5. Press the PCSkeyagaintoconrmthenumber.

6. You may now remove the sample quantity and add

any amount of the material to the platform, and the

display will show a count.

7. You can switch between weighing and counting

mode by pressing PCS or UNITS respectively.

IX. Calibration

Calibration and adjustment are performed at the factory.

However, the weighing range can shift slightly during

shipping. Also, due to changes in local acceleration of gravity

CP4-Series

around the world, adjustment is recommended when moving

the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale

and note the displayed value.

2. If the displayed value is not within acceptable

tolerance (see chart below), adjustment is required.

Model Acceptable

Tolerance (±)

Calibration

Weight

Recommended

Accuracy Class

CP4-100 0.02g 100g OIML M1

CP4-650 0.2g 500g OIML M1

X. Adjustment

1. Press and hold the UNITS key until the display

shows “CAL”.

2. Press the UNITSkeyagain.Thedisplaywillash

“CAL” followed by the calibration weight value (see

chart).

3. Place the calibration weight on the center of the

weighing platform. Make sure you are using the

correctweightforyourspecicmodel.

4. Once the weight is accepted, the display will show

“PASS” then return to normal operation.

XI. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries

• Problem: Displayedweightuctuatesrandomly

• Solution: Make sure your workspace is stable and

free of any air currents or vibration

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment

XII. Error Codes

1. OUTZ - Zero range has shifted. Perform calibration

adjustment. If the problem persists, the load cell may

be permanently damaged due to overloading.

2. 88888 - Maximum capacity exceeded. Remove the

extra weight to avoid damaging the load cell.

3. L - Batteries are low. Replace the batteries.

CP4-100 CP4-650

Max. Capacity 100g 650g

Readability 0.01g 0.1g

Min. Weight 0.03g 0.2g

Power 2 x CR2032 Lithium Batteries

Dimensions 0.5 x 2.4 x 4.5”

Platform Dimensions 2.0 x 2.7”

Warranty 10 Year Limited Warranty

XIII. Capacity/Readability Chart

CP4-100 CP4-650

100g x0.01g

3.528oz x 0.001oz

500ct x 0.05ct

1543gn x 0.1gn

650.0g x 0.1g

22.92oz x 0.01oz

20.89ozt x 0.01ozt

417.9dwt x 0.1dwt

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Escala de otras marcas

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario