Atdec AF-MC Manual de usuario
AF-MC Page 1 of 4
COMPONENT CHECKLIST
Q
Security
Screw
M4 x 16mm
(x1)
F
Pole
Cap
(x1)
D
Pressure
Plate
(x1)
C
Desk Clamp
(x1)
N
Mounting
Screws
M4x10mm
(x4)
L
Cable
Clip
(x1)
J
2mm
Allen Key
(x1)
K
5mm
Allen Key
(x1)
M
Cable
Stop
(x2)
O
Mounting
Screws
M4x12mm
(x4)
P
Mounting
Screws
M4x16mm
(x4)
E
Screw
M8x30mm
(x1)
G
Bolt Through
Plate
(x1)
I
Screw
M8x60mm
(x1)
H
Steel
Washer
(x1)
B
Pole
Assembly
(x1)
A
VESA
head
(x1)
Installation Guide
AF-MC
Micro Desktop Monitor Mount - C Clamp
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
WEIGHT RANGE
• Power Drill
• Drill Bit
• Phillips Head Screwdriver
0 - 8kg
(0 - 17.6lbs)
AF-MC Page 2 of 4
4. Bolt through - Drill Hole
9mm
(3/8”)
25mm
offset
5. Bolt Pole to work surface
Note orientation of
plate with pole
5mm
Allen Key
M8x60mm
Screw
Bolt
Through
Plate
Steel
Washer
1. Desk overview
M8 x 30mm
screw Tighten
rmly
Place pressure
plate on end of
clamp screw
2.2 Place in desired location 2.3 Screw pressure plates in and tighten rmly.
2.1 Attach clamp to post
2. Post mount configuration
6. Install VESA monitor head
VESA monitor
head
Screen
M4x10/12/16mm
Phillips Head Mounting
Screws
6.1 Install VESA monitor head as shown. 100mm
75mm
100mm 75mm
Pressure Plate
Clamp Screw
Allen Key
4.1 Drill 9mm hole in
desired post position
on work surface.
Bolt Through
Desk Clamp
3.2mm
52mm
(2.1”)
(0.1”)
Desktop
MIN THICKNESS - 10mm (3/8”) MAX THICKNESS - 34mm (1,1/4”) THICKNESS RANGE
12mm-40mm (0.5”-1.5”)
AF-MC Page 3 of 4
8. Unlock/Lock Arm Rotation (Note: Focus Micro comes assembled in the “Locked” Position.)
Pole
2mm Allen Key
Grub ScrewMicro Arm
2mm Allen Key
Grub Screw
C
L
Grub Screw Hole
Slot in Pole
Unlock
If you wish your Focus Micro Arm to have 360º rotation
about the Pole you will need to unlock the arm’s rotation
Step 1: Unlock the arm by turning the Grub Screw
anti-clockwise removing the Grub Screw completely
Note: Store the Grub Screw in a safe place if you are to
return the arm to the Locked position
Lock
If you have unlocked your Focus Micro Arm, but wish to
x rotation around the Pole, you will need to lock the arm
Step 1: Ensure the hole for the Grub Screw in the Micro
Arm is lined up with the centre of the Slot in the Pole
Step 2: Re-insert the Grub Screw
previously removed. Turn the Grub
Screw clockwise until it is tight.
Do not over-tighten
7. Mounting Monitor
VESA monitor head
Arm Assembly
7.2 OPTIONAL SECURITY SCREW
Ensure the Monitor is supported, then loosen the Monitor head
screw with the 5mm Allen Key and tilt screen up before installing
the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen
when adjusting tilt.
7.1 Insert VESA monitor head into the
receptacle in the Arm Assembly
5mm Allen Key
Phillips Head
Screwdriver
Loosen
Tighten
Security Screw
Hole
M4 x 16mm
Security Screw
Monitor head
screw
9.1 Unlock ensuring both screen and arm
assembly are supported
9.2 Lift/Lower Screen to the desired
height. Move both Screen and Arm
assembly together.
9.3 Lock Handgrip rmly.
9. Adjusting Height
AF-MC Page 4 of 4
Note: If Focus Micro
is to be used in a multi
user environment, use
the supplied Cable Clip
to secure the display’s
cables to the Pole.
Cable Stop
Cable Clip
Note: Ensure enough
cable slack is given to
allow for movement.
Note: If Focus Micro
is to be used in a multi
user environment, use
the supplied Cable Clip
to secure the display’s
cables to the Pole.
Cable Stop
Cable Clip
Note: Ensure enough
cable slack is given to
allow for movement.
10.2 After connecting cables,
Cable Clips and Cable Stops can
be installed to further manage
cables. Please See Over.
10. Cable Management
11. Insert Cable Stops
Note: Press down rmly onto
the other edge of the Cable
Stop and hold. This allows the
rear prole to ex in place
11.1 Insert Cable Stop on one
edge of the Pole Slot
11.2 Insert allen key into top cap
on pole
Allen Key
Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180723
12. Adjusting the Display Bracket
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
No Allen Key
necessary
No Allen Key necessaryNote: Support Screen when
adjusting tilt.
100mm
75mm
100mm 75mm
5mm
Allen Key
Tighten
Loosen
VESA 75 x 75 / 100 x 100mm
Tabla de contenidos
Otros manuales de Rack y soporte de Atdec
Atdec
Atdec VFS-Q Manual de usuario
Atdec
Atdec Levitate L-PB Manual de usuario
Atdec
Atdec AWMS-2-4640-C Manual de usuario
Atdec
Atdec Visidec Focus Micro Instrucciones de operación
Atdec
Atdec AWM-FC Manual de usuario
Atdec
Atdec ADBS-2x1-17TC Manual de usuario
Atdec
Atdec AWMS-2-LTH75-H Manual de usuario
Atdec
Atdec Spacedec Acrobat Swing Arm Double Manual de usuario
Atdec
Atdec TH-1026-VF Manual de usuario
Atdec
Atdec AF-WD Manual de usuario
Atdec
Atdec AF-AT Manual de usuario
Atdec
Atdec TH-1040-CTS Manual de usuario
Atdec
Atdec Visidec Focus Articulated Arm Wall Instrucciones de operación
Atdec
Atdec Levitate Instrucciones de operación
Atdec
Atdec AWM-A13-B Manual de usuario
Atdec
Atdec AWMS-2-BT75-G Manual de usuario
Atdec
Atdec TH-PFK Manual de usuario
Atdec
Atdec TELEHOOK TH-3060-UT Manual de usuario
Atdec
Atdec AWM-LR Manual de usuario
Atdec
Atdec Telehook Manual de usuario
