Atdec VFS-Q Manual de usuario

VFS-Q Page 1 of 4

Installation Guide

VFS-Q

Freestanding Quad Monitor Mount

COMPONENT CHECKLIST

Crossbar

(x2)

VESA

Plate

(x4)

VFS Display

Head

(x4)

Upright

Pole

(x1)

Base

(x1)

(Optional)

Security Screw

(x4)

Cable Ball

(x8)

3/5mm

Allen Key

(x1 each)

M8x50mm

Screw (x1)

M6x25mm

Cap Screw

(x2)

Mounting

Screw

M4x16mm

(x16)

Mounting

Screw

M4x12mm

(x16)

Mounting

Screw

M4x10mm

(x16)

Cable Clip

(x4)

REQUIRED TOOLS

• Phillips Head Screwdriver

WEIGHT RANGE

Per Monitor

Flat Monitor

0 - 8kg (0 - 17.6lb)

Curved Monitor

0 - 6kg (0 - 13.5lb)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! EachVFSDisplayheadsupportsamaximumweightasperaboveweightrangespecication.

! ThisproductsupportsVESAmountingholecongurations:75x75mmand100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and

offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may

be within the stated range. Please contact Atdec if you would like further information.

NOTE

• 120mm (4.75”) max overall

monitor depth.

• 1kg (2.2lb) maximum weight

difference between monitors.

VFS-Q Page 2 of 4

1. Attach upright pole to base

1.1 Attach the upright pole

to the base as shown below.

Ensure the cable slot faces

towards the rear. Cable Slot

USER

BACK

TIGHTEN

FIRMLY

Upright Pole

M8x50mm Screw

5mm Allen Key

3. Attach the VESA plate to your monitor (Repeat steps 3 to 6 for each monitor)

NOTE: Be sure to select a screw

length that suits the monitor.

3.1 Check VESA mounting compatibility 3.2 Screw VESA plate to back of

monitor using provided screws.

100mm

75mm

100mm 75mm

Top of

monitor

Too short Too long

2. Attach Crossbar and VFS display heads

2.1 Attach crossbar to pole. 2.2 Slide VFS display heads

onto crossbar.

OPEN

SLIDE

DISPLAY

HEAD

ONTO

CROSSBAR

REPLACE

END CAP

CLOSE DISPLAY HEAD LEVER ONCE

IN PLACE ON CROSSBAR.

HOLD SUPPORT IN PLACE

TIGHTEN

M6x25mm Cap Screw

5mm

Allen Key

CLAMP

Cable slot to

face back

OPTIONAL

BOLT THROUGH &

GROMMET MOUNT

Mount can also be bolted

to work surface or via

grommet hole with the

Atdec Grommet Clamp

(AC-GC), sold separately.

VFS-Q Page 3 of 4

Cable

Balls

Cable

Clips

4. Attach your display to the VFS display head

4.1 Hook the top of the VESA plate onto

the display head.

! While mounting the rst monitor,

carefully support mount to prevent

tipping.

4.2 Press and hold the release buttons.

Gently push bottom of VESA plate into

display head. Release buttons to lock

in place.

4.3 (Optional) Insert the security screw, and

tighten using a phillips-head screwdriver.

5. Adjust horizontal position of monitors

HOOK

Back of

Display

OPEN

LOOSEN

TIGHTEN

SLIDE

Release

Button

PUSH

TIGHTEN

Security

Screw

5.1 Open the lever to loosen

the display head.

5.2 Slide the display head to

desired position.

5.3 If necessary, adjust the

tension between the display

head and the pole using the

5mm allen key supplied.

5.4 Close the lever to lock the

display head in place.

6. Adjust the ball joint tension 7. Cable Management

6.1 If the monitors are not holding position or are

sti to move, adjust the tension plate by tightening

or loosening the three screws.

Note: Adjust 3

screws evenly in

small increments

Note: Support the monitor while making adjustments.

3mm

Allen Key

7.1 Connect cables to your displays, routing them down the rear

of the poles. Push the cables into the slots, using either the

cable balls or cable clips to secure them to the pole as shown.

Cable

Balls

Cable

Clips

Note Ensure enough slack is left in cables

to allow for movement. When the slot in

each pole cannot be used, use the supplied

cable clips to secure the display cables.

Note: support monitor

weight to aid sliding.

VFS-Q Page 4 of 4

8.1 Remove monitors

8.3 Remove crossbar from pole

8.5 Lock display head onto pole

OPTIONAL 8. Switch to a triple, dual or single monitor mount

Example

8.2 Slide display head o crossbar

8.4 Slide display head onto pole

UNLOCK

REMOVE

END CAP SLIDE DISPLAY HEAD

OFF CROSSBAR

Slot

UNLOCK

SLIDE DISPLAY

HEAD ONTO POLE

(Ensure tongue in

display head aligns

with slot in pole)

Tongue

REMOVE

POLE CAP 1

PRESS AND

HOLD BUTTONS

LIFT OFF MONITOR

PULL OUT BOTTOM

OF MONITOR

SUPPORT

CROSSBAR

UN-SCREW

CROSSBAR

(Use 5mm

Allen Key)

REMOVE

CROSSBAR

FROM POLE

REPLACE

POLE CAP

LOCK DISPLAY HEAD

TO POLE

Re-attach monitor

following steps 4.1 to 4.3

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Otros manuales de Rack y soporte de Atdec

Atdec

Atdec AF-MC Manual de usuario

Atdec

Atdec TH-1040-CTS Manual de usuario

Atdec

Atdec AWMS-2-BT75-FS Manual de usuario

Atdec

Atdec AD-WFP-5040 Manual de usuario

Atdec

Atdec Focus VF-AT-NP Manual de usuario

Atdec

Atdec AWMS-46W35 Manual de usuario

Atdec

Atdec 8060 Manual de usuario

Atdec

Atdec Visidec Focus Articulated Arm Wall Instrucciones de operación

Atdec

Atdec AWM-W35 Manual de usuario

Atdec

Atdec Visidec Focus Micro Manual de usuario

Atdec

Atdec 8060 Manual de usuario

Atdec

Atdec TH-2050-VFM Manual de usuario

Atdec

Atdec ADBS-2x2-17MFB Manual de usuario

Atdec

Atdec Freestanding Quad Manual de usuario

Atdec

Atdec Telehook Manual de usuario

Atdec

Atdec AF-AT-NBC Manual de usuario

Atdec

Atdec TH-3060-UFL Manual de usuario

Atdec

Atdec TELEHOOK TH-3060-UT Manual de usuario

Atdec

Atdec AD-TVC-70A Manual de usuario

Atdec

Atdec AWM-A13 Manual de usuario

Atdec

Atdec AD-WM-7060 Manual de usuario

Atdec

Atdec AWM-LR Manual de usuario

Atdec

Atdec AWMS-3-137140-C Manual de usuario

Atdec

Atdec AF-AN Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario