Atdec AWMS-2-BT75-G Manual de usuario
AWMS-2-BT75-G Page 1 of 4
Scan to access
more information
Installation Guide
AWMS-2-BT75-G
COMPONENT CHECKLIST
B
Bridge
(x1)
C
Leg
(x2)
I
Post
(x1)
C
Bracket
(x2)
M
4mm/5mm
Hex Key
(x1 each)
N
13mm
Spanner
(x1)
D
VESA Plate
(x2)
A
M8 Stud
(x1)
J
M4x10mm
Screw
(x8)
F
M8 Nut
(x1)
H
Post Cap
(x1)
K
M4x20mm
Screw
(x8)
L
10mm
Spacer
(8x)
B
M8x30mm
Screw (x1)
G
M8 Stud
(x1)
H
M8x30mm
Screw
(x1)
G
Clamp Bar
(x1)
E
Clamp Plate
(x1)
C
Clamp Bar
(x1)
B
Clamp Plate
(x1)
IMPORTANT INFORMATION
! Product should only be assembled and used as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Eachbracketsupportsamaximumweightasperabovecapacityspecication.
! Avoid applying downward load to corners of display.
! Product must only be installed on a solid work surface capable of supporting the weight of all equipment being mounted.
! The product is compatible with desk thicknesses from 18 - 36mm (0.71 - 1.42”)
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you
would like further information.
! WARNING! Death or serious injury may occur if a child climbs on or tips product.
Post Mounted Heavy Duty
Dual Vertical Monitor Mount
Grommet Clamp
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY (per monitor)
Flat Monitor
4.5 - 25kg (10 - 55lb)
Curved Monitor
4.5 - 18kg (10 - 40lb)
Display Size
24” - 55”
300mm (12”) max overall
display depth
AWMS-2-BT75-G Page 2 of 4
2. Attach grommet clamp on desk
Option A - Through grommet hole
80mm (31
/
8”) max hole diameter
1. Assemble post to clamp plate
1.1
Option B - As heavy duty bolt through
75mm
100mm
75mm
100mm
NOTE:
For 75mm VESA unscrew
5mm to access top holes
Option A
Attach VESA plate
with M4x10mm
screws.
Option B
For recessed VESA
use 10mm spacers
and M4x20mm
screws.
3.1 VESA compatibility.
NOTE:
Some displays require the use of
a VESA adapter before attaching
the VESA plate. This VESA adapter
may ship in the box with the display.
Consult your display’s installation
guide for further information.
3. Attach VESA plates to displays
D
J
TOP
D
K
L
I
A
M
B
E
AB
G
F
N
9mm
(3/₈’’)
60mm (2⅓”)
minimum
G
F
N
Installed position
AWMS-2-BT75-G Page 3 of 4
4. Slide brackets onto post and set height
4.1 Line up the inner guide
on rear of bracket with rear
channel on post.
C
MEASURE
≥Display
height
between
brackets
H
MEASURE to
ensure clearance
to desk
HOLE
in desk
FRONT
of display
INNER
GUIDE
in rear
post
channel
VIEW FROM ABOVE
WARNING:
Ensure clips
closed before
tilting
5. Attach bottom display
6. Set tilt
5.1 Set VESA plate clips
to open position.
Bottom display must be
attachedtobracketrst.
WARNING:
Use two people to install
display
5.4 Set VESA plate
clips to closed position.
6.1 Adjust display tilt
angle by gripping edges
of screen and rolling up or
down to desired position.
TILT KNOBS
6.2 Set display
angle by tightening
tilt knobs.
5.3 Centre VESA plate close to
post and slowly lower until bar on
VESA plate sits in saddle in bracket.
5.2 Lift display until
VESA plate is above
the bracket.
OPEN
OPEN
CLOSED
CLOSED
NOTE:
Display hangs from the
bracket like a painting.
After clips are closed,
if corners of the screen
are pushed downwards,
rocking movement is
expected.
WARNING:
Do not loosen
hand knob with
display attached
Clockwise = More friction
Anti-clockwise = Less friction
OPTIONAL ADJUSTMENT - TILT FRICTION
4mm hex key can be used to reduce tilt
friction (for light screen) or increase tilt
friction (for heavy screen).
F
4.3 Firmly tighten
hand knob at chosen
height.
MEASURE
≥Display
height
between
brackets
H
MEASURE to
ensure clearance
to desk
TIGHTEN
WARNING:
Never loosen knob
while display is on
bracket
4.4 Ensure height is
sufcientfordisplayto
clear desk once in place.
Repeat with
second
bracket and
tpostcap.
4.2 Slide inner
guide into channel,
then lower bracket.
D
Arrow side
towards user
AWMS-2-BT75-G Page 4 of 4
Cables can
exit from
the side of
the cable
cover
PUSH
PUSH
PUSH
Please Recycle
8. Fine Adjustment
7. Attach top display
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reservestherighttoalterspecicationswithoutnotice.©20230120
7.1 Check that distance between brackets
is equal to or greater than the height of
the display. (See image in Step 4.4)
7.2 Repeat Step 5 & Step 6 to
attach top display and set tilt
angle.
Unstacked Stacked
9. Cable Management
9.1 Load cables into
cable clip.
9.2 Insert one side of the
cable clip into a channel
on the post, then push in
the other side.
Load cables into
cable cover
9.3 Load
cables into
cable cover.
9.4 Clip the cable cover
back onto rear post
channels.
8.1 To correct horizontal angle
of display +/- 3 °:
Turnasinglenetune
adjustment knob to adjust
angle of screen.
Clockwise = Higher
Anti-clockwise = Lower
8.2 To close small gap between
displays +/-6mm (1/4”):
Turnbothnetuneadjustment
knobs - alternating sides a few
rotations at a time.
Clockwise = Higher
Anti-clockwise = Lower
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
Lower
Close
Adjust angle
Set angle
i
ii
iii
iv
FINE HEIGHT ADJUST
FINE ADJUSTMENT
KNOBS
NOTE:
Ensure clips are in
CLOSED position
WARNING:
Damage to monitors may occur
ifthereisinsufcientspacing
between brackets. Top monitor
must hang in bracket - not be held
up by the monitor below it. After
bothdisplaysareattached,usene
adjustment to close gap between
them (see Step 8).
Otros manuales de Rack y soporte de Atdec
Atdec
Atdec VISIDEC FOCUS MICRO Instrucciones de operación
Atdec
Atdec AWM-A46-B Manual de usuario
Atdec
Atdec AWMS-2-BT75 Manual de usuario
Atdec
Atdec AWM-W6 Manual de usuario
Atdec
Atdec ADBS-3x1-30T3C Manual de usuario
Atdec
Atdec AD-WM-5060 Manual de usuario
Atdec
Atdec AWM-AD Manual de usuario
Atdec
Atdec AWM-BT Manual de usuario
Atdec
Atdec VFS-DV Manual de usuario
Atdec
Atdec Visidec Focus Micro Instrucciones de operación
Atdec
Atdec A-STSWW-A Manual de usuario
Atdec
Atdec AWMS-3-137140-C Manual de usuario
Atdec
Atdec AWMS-BT40 Manual de usuario
Atdec
Atdec AWM-BT Manual de usuario
Atdec
Atdec A F -AT-W Manual de usuario
Atdec
Atdec AF-AN Manual de usuario
Atdec
Atdec AWM-W6 Manual de usuario
Atdec
Atdec AWMS-DW6 Manual de usuario
Atdec
Atdec Telehook Manual de usuario
Atdec
Atdec Freestanding Quad Manual de usuario
