Atdec AWMS-DW6 Manual de usuario
AWMS-DW6 | Page 1 of 7
Installation Guide
AWMS-DW6
Dynamic Monitor Arm on Wall Mount
COMPONENT CHECKLIST RANGE
CONTENTS
A
AWM-AD
Dynamic Arm
(x1)
B
AWM-LC
Post Clamp
(x1)
B
AWM-W6
60 Wall Channel
(x1)
60 Wall Channel
Page 2
Page 3
Dynamic Arm
Page 4
Page 5
AWM-W6
Component Checklist
Channel Installation
AWM-AD
Component Checklist
Arm Installation
AWMS-DW6 | Page 2 of 7
AWM-W6
Wall Channel
COMPONENT CHECKLIST
A
Wall channel
(x1)
E
Nylon
Anchor (x2)
C
Top Cap
Screws
(x2)
B
Top Cap
(x1)
D
M6 x 50mm
Countersunk
Screw (x2)
REQUIRED TOOLS
• Power Drill
• 4mm (5/
32”) Drill Bit
• 8mm (5/
16”) Drill Bit
• Phillips Head Screwdriver
0 - 12kg
(0 - 26.5lbs)
per monitor
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with AWM Series products.
! The manufacturer accepts no responsibility for incorrect installation.
AWMS-DW6 | Page 3 of 7
3.1 Fit Top Cap
Phillips Head
Screwdriver
Top Cap
1. Install Wall Channel - Ensure all fasterners are installed
2. Fit channel clamp to wall channel
3. Fit top cap to wall channel
8mm (5/
16”) holes
4mm (5/
32”) holes
Nylon anchors
M6 x 50mm
Screws
M6 x 50mm
Screws
1.1 Masonry 1.2 Timber stud
2.1 Ensure knob is undone. 2.2 Slide clamp into channel.
Push knob to
aid insertion
2.3 Hold clamp in desired position on post
and turn knob to lock in place.
1. Ensure Knob is undone
Tip: push knob
to aid insertion
2. Slide clamp into channel
3. Hold clamp in desired position on post and turn
knob to lock in place
AWMS-DW6 | Page 4 of 7
AWM-AD
Dynamic Arm
COMPONENT CHECKLIST
REQUIRED TOOLS
A
Dynamic
Monitor Arm
(x1)
B
VESA
head
(x1)
C
Screw
M4x25mm
(x4)
D
Screw
M4x16mm
(x4)
E
Screw
M4x12mm
(x4)
F
Spacer
(x4)
G
Security
screw
(x1)
H
4mm
allen key
(x1)
• Phillips Head Screwdriver
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec AWM Series products.
! The Dynamic Arm (AWM-AD) requires a Channel Clamp (AWM-LC, sold separately) for installation on an AWM Post.
! The Dynamic Arm (AWM-AD) requires a Desk Base (AWM-LB, sold separately) for installation directly onto an AWM fixing.
! The manufacturer accepts no responsibility for incorrect installation.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the
capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further
information.
Flat Monitors
0 - 9kg
(0 - 20lbs)
Curved Monitors
0 - 6kg
(0 - 13.5lbs)
Monitor weight should be within the
weight range of all modular elements
that make up the complete monitor
mounting solution.
AWMS-DW6 | Page 5 of 7
1. Set arm rotation to 180° (optional)
2. Fit arm onto Base or Channel Clamp (sold separately)
Note: Check the
arm rotation is
smooth after
tightening.
2.1 Push arm onto shaft. 2.2 Ensure arm is fully pushed onto shaft. 2.3 Tighten joint screw.
1.1 On the Base or Channel
Clamp (sold separately)
Remove plastic sleeve.
1.2 Remove rotation ring. 1.3 Place rotation ring in the
desired position.
Channel Clamp Ring Position
When setting channel clamp rotation,
orientate the ring depending on what
post channel the arm will be attached
to. The tag on the ring should always
face towards the user.
180°
360°
OR
Default
Position
Flipped
Position Tag
1. Press
2. Lift
3.2 Attach VESA head onto monitor with
provided screws.
3. Attach VESA head to monitor
100mm
75mm
100mm
75mm
Flush
Too long Too short
Spacer
5mm 12mm
3.3 Be sure to use correct screw length3.1 VESA mounting compatibility
100mm
75mm
100mm
75mm
Flush
Too long Too short
Spacer
5mm 12mm
Note: For other sizes, use a suitable
adaptor plate (sold separately).
Note:
Spacers may
be required
for curved,
recessed
or uneven
monitor
surfaces.
4. Mount monitor on arm
Monitor arm
4.2 Ensure that the VESA head sits ush within
the monitor arm. There should be no gap.
4.1 Insert VESA head into the monitor arm 4.3 Push the lever down to secure
it to the arm assembly
Gap No Gap
AWMS-DW6 | Page 6 of 7
5. Adjust tilt tension & install security screw
5.1 Use the allen key to adjust the tilt tension until the monitor
holds in a vertical position at the end of the arm.
Note: Support
monitor while
adjusting.
Tighten
Loosen
Tighten
Loosen
5.2 OPTIONAL security screw
Tilt the head upwards to install the optional security screw.
7. Tension gauge
7.1 When installing
multiple monitors
of a similar weight,
use the tension
gauge to make
installation faster.
1. Set up one monitor and
record the position of the
marker on the gauge.
2. When installing subsequent
monitors, pre-tension the
arm to the recorded amount,
then ne-tune the tension by
following steps 6.3 to 6.5.
Arm Tension Gauge
Marker
Heavier
Monitor
Lighter
Monitor
6. Adjust arm tension
6.1 To accurately set the tension of the arm, position
the monitor at 90 degrees
6.2 Use the allen key to adjust the arm tension to the weight of the
monitor. Follow steps 6.3 to 6.5 to set the tension.
6.3 If the monitor sags or falls down,
increase the arm tension by rotating
the screw clockwise.
6.5 If the monitor oats or hovers in all
positions the arm tension is balanced
and does not require further adjustment.
6.4 If the monitor springs upwards from the
bottom position, decrease the arm tension
by rotating the screw anti-clockwise.
Monitor Falls
(from top)
Increase Tension
Monitor ‘Floats’
(all positions)
Balanced
Monitor Springs
(from bottom)
Reduce Tension
90°
AWMS-DW6 | Page 7 of 7
8. Cable management
8.1 Plug cables into the monitor and
route the cables down the arm using
the cable hooks and clips.
See steps 8.2 to 8.4
8.2 Wedge cable into the central gap
and slide it down the arm.
8.3 The cable should slip into the arm cavity 8.4 Slide the remaining loose cable
from the central gap up the arm.
Important!
Ensure enough cable slack is
given in this area to allow for
movement of the monitor.
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20200402A
Este manual sirve para los siguientes modelos
2
Otros manuales de Rack y soporte de Atdec
Atdec
Atdec 8060 Manual de usuario
Atdec
Atdec AWMS-2-D13-C Manual de usuario
Atdec
Atdec AD-WFP-5040 Manual de usuario
Atdec
Atdec ADBS-2x1-17TC Manual de usuario
Atdec
Atdec Visidec Focus Articulated Arm Wall Instrucciones de operación
Atdec
Atdec ADBS-2x2-17MFB Manual de usuario
Atdec
Atdec AWM-LTH Manual de usuario
Atdec
Atdec Focus VF-AT-NP Manual de usuario
Atdec
Atdec AWM-A46 Manual de usuario
Atdec
Atdec AF-AA Manual de usuario
Atdec
Atdec TH-1040-CTS Manual de usuario
Atdec
Atdec AWMS-2-BT75-FS Manual de usuario
Atdec
Atdec ADB-FS Manual de usuario
Atdec
Atdec AWM 460 Arm Manual de usuario
Atdec
Atdec AWMS-2-BT75-FS Manual de usuario
Atdec
Atdec AWM-A71-B Manual de usuario
Atdec
Atdec AF Series Manual de usuario
Atdec
Atdec VFS-DH Manual de usuario
Atdec
Atdec ADBS-3x1-30T3C Manual de usuario
Atdec
Atdec AWM Series Manual de usuario
