ACME LED-ST1000 Manual de usuario





15B

Innovation, Quality, Performance

Ultra Strobe

LED-ST1000

User Manual

Please read the user manual before use





1B





14 B

Single Flash

Single flashes can be achieved by pressing the SINGLE FLASH button. Switch on the

“BLACK OUT” and indicator LED light up, to press the SINGLE FLASH button for

triggering a single flash effect.

6. Technical Specifications

AC power . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .100 - 240 V , 50/60 Hz

AC mains power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . …………….. . . . . . 2 m2

LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 3w/99pcs LED

Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479×107.5×174mm

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .. .2.7kg

Ambient air temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .40° C (104° F)

Short‐circuitprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . T6.3A

Safety Installation Distance

Minimum distance to combustible materials. . . . . . . . . . . . . . . . . . . . . . . . ……0.5 m

Minimum distance to illuminated surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . …10m





13B

The optional remote control for BF-04D provides the following:

Slider controls for chase speed and intensity.

Momentary push button control of the blinder effect, when the LED of

BLACK OUT is on, that means chase is stop.

Momentary push button for single flash and flash synchronization, when

the LED indicator of BLACK OUT is on, that means chase is stop.

Chase number toggle switch

Chase mode toggle switch: AUTO/SOUND

DATA CONNECTION

Important: Do not terminate the data link when using the BF-04D!

The remote controller connects to The LED-ST1000 with a 3-pin XLR data

cable. Additional LED-ST1000 may be connected in series, output to input.

Note, however, that the data link must not be terminated as described DMX

controllers and the LED-ST1000 should change to the remote control function.

OPERATION

Intensity

Flash intensity is controlled from 20% of the maximum Intensity to 100%

of the maximum Intensity with the DIMMER fader.

The maximum intensity is reduced in low power mode, which is selected

on pin 6 of the Mode DIP switch.

Chase Speed

Chase speed is controlled from slow to fast with the SPEED fader.

The BLACK OUT button toggles chase run on and off. The indicator diode

is on when chase stopped and off when chase running.

Chase Number

Toggle Chase number with Chase button and will be shown on the nixie tube.

Chase Mode

Toggle Chase running way with MODE button: AUTO/SOUND mode. The

corresponding LED indicator will display the selected mode.

Blind Effect

The blinder effect is controlled with the FULL ON button. The intensity is the

maximum Intensity. LED power is electronically regulated to prevent the LED from

overheating.





2 B

Table of Contents

1，Safety Information…………………………………………………. 3

2，Rear Panel…………………………………………………………. 5

3，Preparation for Use ………………………………………………...6

4，Main Function …………………………………………………….. 6

5，Remote Control…………………………………………………….12

6，Technical Specification…………………………………………….14





3B

1. Safety Information

Warning: This product is for professional use only! It is not for

household use.

The LED-ST1000 presents risks of lethal or severe injury due to fire and

heat, electric shock, ultraviolet radiation, and falls. Flashing light is also

known to trigger epileptic seizures in persons who are photosensitive.

Read this manual before powering or installing the fixture, follow the

safety precautions listed below and observe all warnings in this manual

and printed on the fixture.

Noted: high voltage in the LED board!

Super power strobes, so please avoid extended periods of

continuous flashing

To guard against electric shock

Do not remove the rear cover: there are no user-serviceable parts inside.

Always ground (earth) the fixture electrically.

Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

Do not expose the fixture to rain or moisture.

To guard against UV radiation, burns, and fire

Never attempt to bypass the fuse. Always replace defective fuses with ones of the

specified type and rating.

Verify that the power feed cable is rated for the current draw of all connected

fixtures.

Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters

(20 inches) away from the fixture. Keep flammable materials well away from the

fixture.

Minimum distance to illuminated surface is 10 meters.

Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

Never place filters or other materials over the front glass cover.

The exterior of the fixture can reach temperatures up to 120° C (248° F). Allow the

fixture to cool for at least 15 minutes before handling.

Do not modify the fixture or install other than genuine parts.





12 B

The easy remote control is used only in master/slave mode. By connecting to the

first master unit, you will find that the remote controller on the first unit will

control all the other units for Standby, Function and Mode selection

BF-04D connected LED-ST1000,and under the 2-channel DMX mode,that’s

LED-ST1000 will be flashed as chase and intensity by BF-04D .

How to connect

When connected to the remote control BF-04D, the LED-ST1000 flashes

with controlled chase and intensity when the Strobe button is pressed on

the BF-04D.

STAND BY Blackout the unit (the LED indicator will light on/off

accordingly)

FUNCTION

1. Short Enter can be shifted Synchronous

Strobe/Random Strobe/ sound Strobe；（Mode1）

2. Short Enter can be shifted Show effect（Mode2）

3. Long Enter means lighting tension is Max ；

（Mode3）

MODE

1，Strobe (LED indicator off)；（default mode）;

2，Show mode. (LED indicator flash)；

3，lighting tension is Max （LED indicator on）；





11B

Hz power supplies or from 0 to 20 flashes per second on 60 Hz power supplies, on

channel 3 in the 3- and 4-channel DMX modes. Flash rate is also controllable in 1-

and 2-channel DMX mode.

Built-in effects

Six programmed effects are available on channel 4 in the 4-channel DMX mode

only. The effects may be altered using the intensity, duration, and rate controls.

Ramp up: Light gradually increases in intensity, and then blacks out.

Ramp down: Light flashes to full intensity, and then gradually fades.

Ramp up-down: Light gradually increases and decreases.

Lightning: The flashes simulate lightning. Duration is not adjustable.

Random flash: Light flashes randomly with variable rate and intensity. Multiple

units flash independently of each other.

Blind effect

The blinder effect, in which the light remains on for an extended period, is

available in all DMX modes. In the 3- and 4-channel modes, the effect is

achieved by the combination of flash duration and rate prevents pauses

between flashes. For example, the blinder effect can be achieved with a flash

duration of 0.25 seconds (250 ms) and a flash rate of 4 flashes per second, or a

flash duration of 0.05 seconds (50 ms) and a flash rate of 20 flashes per

second.

In 3- and 4-channel DMX mode, the intensity of the blinder effect is controllable

on channel 1. LED power is electronically regulated to prevent the LED from

overheating. The intensity falls as power is reduced.

Single Flash

To trigger single flashes, start with the intensity and flash rate at 0 and then set

the intensity on channel 1. When the value of channel 1 is changed, the light

will flash once with the programmed intensity, duration, and effect.

5. Easy Controller





4 B

Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104°

F).

To guard against falls

When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

Block access below the work area whenever installing or removing the fixture.

To guard against epileptic seizure

Do not operate the fixture near stairways.

Provide advance notice that strobe lighting is in use.



For AC 220-240V power supply, the maximum fixtures that can be

connected on one power cable is 6(including the first fixture) ;

For AC 100~120V power supply, the maximum fixtures that can be connected

on one power cable is 3 (including the first fixture).





5B

2. Rear Panel

1, Mains input/output:

Connect to supply mains power, and connect to supply mains power for

the next unit.

2, Fuse holder: T6.3A

3. LED display

4, LED indicator:

Signal Flash Signal input present

Master On Master

Slave On Slave

Sound Flash Sound active signal input

5, Menu /UP/DOWN/ Enter button

6, DMX input/output

7, Sound Active Port: Receive Sound active signal

8, CA-8 Connector: Connect with easy controller CA-8





10 B

DMX CONTROL SUMMARY

Intensity

Flash intensity can be set from minimum (blackout) to maximum on 1-channel DMX

modes, channel 2 in 2-channel DMX modes and channel 1 in the 3- and 4-channel

DMX modes.

The maximum intensity can be reduced by selecting low power mode as described

Duration

Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530 ms

on 60 Hz power supplies, on channel 2 in the 3- and 4-channel DMX modes. Flash

duration is fixed in 1 channel DMX mode.

Rate

Flash rate can be set from 0 flashes per second to 17.5 flashes per second Hz on 50





9B

several seconds self-test, it will return to main interface. If you want back to

main menu, please hold MENU button for 1 second.

Temperature

Select the LEMP, press ENTER button and the display will show the

temperature of unit. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second.

Defaults

Select DEF option, press ENTER button, Use UP/DOWN button if you would

like reset defaults,or not. press ENTER button to confirm your

selection. If you want back to main menu, please hold MENU button for 1

second.

Check the version number

Select the VER, press ENTER button to confirm. You can see the current

version number now and check them by UP/DOWN. Wait for 30 seconds, it

will return to main interface. If you want back to main menu, please hold

MENU button for 1 second.

Channel Mode:





6 B

3. Preparation for Use

INSTALLATION

The LED-ST1000 may be installed in any orientation. The mounting bracket provides

one 12 mm holes for direct fastening or attachment of rigging clamps.

4. MAIN FUNCTION

Press MENU button enter the function, then use UP/DOWN or MENU button

to select the function you want, final press ENTER button to confirm the

function you select. Wait for 30 seconds, it will return to main interface. If

you want back to main menu, please hold MENU button for 1 second. The

main menu as follow:

DMX 512 address setting

Select ADDR option and the display will blink, press ENTER button to

confirm your selection. You can check the current DMX address from LED

display. The DMX address can be changed by press UP/DOWN button and

then press ENTER button to confirm your selection. Wait for 30 seconds, it





7B

will return to main interface. If you want back to main menu, please hold

MENU button for 1 second.

Channel mode setting

Select CHMD option, press ENTER button to confirm your selection. Change

the channel way (1/2/3/4/) by press UP/DOWN button. Press ENTER button

to confirm your selection. Wait for 30 seconds, it will return to main interface.

If you want back to main menu, please press MENU button.

Master/Slave Mode

Select the , press the ENTER button. Use the DOWN and UP button

to select (Master) 、-（Slave）（ Note: Each 4 units as

one show group,Slave will performance with Master once reset .

Press the ENTER button after selected. Or exit menu mode without any

change after 8 seconds automatically. If you want back to main menu,

please press MENU button.

Show Mode

Select the , press the ENTER button. Use the DOWN and UP button to

select - ,is Random Show Mode, 13 performance

effect will be available once lighting is Master.

Blackout Mode

Select the , press the ENTER button. Use the DOWN and UP button to

select (when without DMX signal, the output will be “0”) or

(when without DMX signal, the master will run the built-in CHASE ,and the

slave will keep the same running status ). Once selected, press the ENTER

button to setup or exit menu mode without any change after 8 seconds

automatically. Back to the functions without any change press the MENU

button again.





8 B

Sound Mode

Select the , press the ENTER button. Use the DOWN and UP

button to select / .Sound mode will be available once lighting

is Master.

Sound sense

Select the ,press the ENTER button. Use the DOWN and UP button to select

the sensitivity (000-100). Once selected, it can be control Sound sensitivity once

lighting is Sound Mode.

LED display setting

Select the LED option, press ENTER button to confirm your selection. You

can see the current ON/OFF status of LED display now. You can change its

status by press UP/DOWN button. Then press ENTER button to confirm your

selection. If you choose OFF, than the LED display will close without any

operation for I min. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

LED display direction setting

Select DISP option, press ENTER button to confirm your selection. Select

the DISP / DSIP by press UP/DOWN button. Press ENTER button to confirm

your selection. Wait for 30 seconds, it will return to main interface. If you

want back to main menu, please hold MENU button for 1 second.

Test setting

Select TEST option, press ENTER button to confirm your selection. The

flash indicator will light up and the unit will test automatically. Wait for

Otros manuales de Equipo de DJ de ACME

ACME

ACME Solaris CM-S6 Manual de usuario

ACME

ACME ELLIPSOIDAL E-300 Manual de usuario

ACME

ACME LED-BL4B Manual de usuario

ACME

ACME ENERGY SPOT XA-400 SPOT Manual de usuario

ACME

ACME 04XOZONE Manual de usuario

ACME

ACME WHACK XP-231 BEAM Manual de usuario

ACME

ACME Junior Series Manual de usuario

ACME

ACME LED-MTX25 IP Manual de usuario

ACME

ACME LED-747-1W Manual de usuario

ACME

ACME LED-MS50A Manual de usuario

ACME

ACME Color Fusion CF-805 Manual de usuario

ACME

ACME LS-608 RGB Manual de usuario

ACME

ACME LED WAVE 100 Manual de usuario

ACME

ACME FURY LED RGB Manual de usuario

ACME

ACME XA-500 Manual de usuario

ACME

ACME LED-RC8 Manual de usuario

ACME

ACME PAGEANT 300ZR II Manual de usuario

ACME

ACME MINI ELLIPSOIDAL 10 Manual de usuario

ACME

ACME LED WAVE 100 Manual de usuario

ACME

ACME LP-F2000 VW Manual de usuario

ACME

ACME XP-470 BSW Manual de usuario

ACME

ACME Dragonfly Quad Manual de usuario

ACME

ACME LED-MS150 Manual de usuario

ACME

ACME LP-TS200 CW Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario