ACME LED-BL4B Manual de usuario

Stage Blinder B4

LED-BL4B

User Manual

Please read the user manual before use

Contents

1. Safety Instructions……………………………………………………….2

2. Technical Specifications…………………………………………………5

3. Installation…………………………………………………………………6

4. How to set the unit………………………………………………….…….6

4.1 Rear Panel…………………………………………………………………6

4.2 Main Function…………………………………………………………….8

5. How To Control The Unit………………………………………………..12

6. DMX Channel Mode……………………………………………………….13

7. DMX512 Connections…………………………………………………....15

8. Troubleshooting……………………………………………………………16

9. Fixture Cleaning…………………………………………………………….17

1. Safety Instructions

WARNING



Please keep this User Manual for future consultation. If you sell the fixture to another user,

be sure that they also receive this instruction booklet.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

Please unpack and check carefully there is no transportation damage before using the

fixture.

Please disconnect main power before servicing and maintenance.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

The maximum ambient temperature is Ta: 40℃. DO NOT operate it where the

temperature is higher than this.

DO NOT connect the device to any dimmer pack.

The housing must be replaced if they are visibly damaged.

Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool

down before replacing or serving.

There are no user serviceable parts inside the fixture. Do not open the housing or attempt

any repairs by yourself. In the unlikely event your fixture may require service, please

contact your nearest dealer.

In the event of serious operating problem, stop using the fixture immediately. Never try to

repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage

or malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

It’s important to ground the yellow/green conductor to earth in order to avoid

electric shock.

DO NOT touch any wire during operation and there might be a hazard of electric shock.

DO NOT expose the fixture to rain or moisture, in order too prevent or reduce

the risk of electrical shock or fire.

Do not look directly at the LED light beam while the fixture is on.

2. Technical Specifications

DMX 1/2/4/5 channels switchable.

Dimming, Strobe, Sound Active and easy controller CA-8

Two operation modes: DMX, Master/Slave.

Ideal for discotheques, clubs, bars, parties, Mobile DJs, etc.

Input Voltage: AC 100V~240V 50/60Hz

Total Power consumption: 400W

Fuse: T6.3A

LED: 4 x 65W LED

Dimension: 868X141X306mm

Weight: 7.5Kgs

For AC 220-240V power supply, the maximum fixtures that can be connected on

one power cable is 4(including the first fixture) ;

For AC 100~120V power supply, the maximum fixtures that can be connected on

one power cable is 2 (including the first fixture).

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight

of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

4. How to set the unit

4.1 Rear Panel

○

1 Mains input/output:

Connect to supply mains power, and connect to supply mains power for the next unit.

○

2 Fuse holder: T6.3A

○

3 CA-8 Connector: Connect with easy controller CA-8

○

4Sound Active Port: Receive Sound active signal

○

5DMX input/output:

For DMX512 link, use 3-pin XLR plug cable to input DMX signal, and to link the next unit.

○

6Button:

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

○

7 LED indicator:

Signal

Flash

Signal input present

Master

Slave

Sound

Flash

Sound active signal input

○

8Display: Show the various menus and the selected functions

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button. Use DOWN and UP button to change the mode. Once

the required mode has been selected, press ENTER button to setup or it will return to the

main functions without any change after idling 8 seconds automatically. Back to the functions

without any change press MENU button. The main functions are shown below:

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to change the DMX 512 address（001-512）. Once the address has been selected,

press the ENTER button to setup or exit menu mode without any change after 8 seconds

automatically. Back to the previous functions without any change press the MENU button.

Channel Mode

Select the , press the ENTER button. Use the DOWN and UP button to select the

channel mode (1/ 2/4/5CH)( 1 channel mode control bright of 4 LED, 2 channel mode means

1st channel mode control bright of 4 LED , 2nd channel control effect of 4 LED, 4 channel

mode control bright of 4 LED by separate, 5 channel mode control bright of 4 LED by

separate, and 5th channel control effect of 4 LED ). Once selected, press the ENTER button to

setup or exit menu mode without any change after 8 seconds automatically. To go back to the

functions without any change,pls press the MENU button

Master/Slave Mode

Select the, press the ENTER button. Use the DOWN and UP button to select

(Master) 、（Slave）（Note: Each 2 units as one group, such as MAST, SL01 as one

group, SL00, SL01 as another group.）, after selected, press the ENTER button. Or exit menu

mode without any change after 8 seconds automatically. To go back to the functions without

any change press the MENU button.

Sensitivity

Select the ,press the ENTER button. Use the DOWN and UP button to select the

sensitivity (000-100).Once selected, press the ENTER button to setup or exit menu mode

without any change after 8 seconds automatically. To go back to the functions without any

change press the MENU button

LED display

Select the , press the ENTER button. Use the DOWN and UP button to select

(LED display on) or (LED display off, after 30 sec. without any move, display will off

again). Once selected, press the ENTER button to setup or exit menu mode without any

change after 8 seconds automatically. Back to the functions without any change press the

MENU button again.

Display direction

Select the , press the ENTER button. Use the DOWN and UP button to select

(positive display) or (reverse display). Once selected, press the ENTER button to

setup or exit menu mode without any change after 8 seconds automatically. Back to the

functions without any change press the MENU button again.

Blackout Mode

Select the , press the ENTER button. Use the DOWN and UP button to select

(when without DMX signal, the output will be “0”) or (when without DMX signal, the

master will run the built-in CHASE ,and the slave will keep the same running status ). Once

selected, press the ENTER button to setup or exit menu mode without any change after 8

seconds automatically. Back to the functions without any change press the MENU button

again.

Temperature Display

Select the , press ENTER button and the display will show the temperature of each

unit ，. To go back to the functions press the MENU button.

Firmware version

Select the , press ENTER button and the display will show the version of software of the

unit. To go back to the functions press the MENU button.

Tabla de contenidos

Otros manuales de Equipo de DJ de ACME

ACME

ACME LED?7TC Manual de usuario

ACME

ACME Dragonfly Quad Manual de usuario

ACME

ACME LP-TS200 CW Manual de usuario

ACME

ACME MINI ELLIPSOIDAL 10 Manual de usuario

ACME

ACME MP-400Z IP Manual de usuario

ACME

ACME LED-PAR 100 WW/CW Manual de usuario

ACME

ACME MH-640S-ELC Manual de usuario

ACME

ACME LED WAVE 100 Manual de usuario

ACME

ACME PAGEANT 300ZR II Manual de usuario

ACME

ACME Dotline 360 Manual de usuario

ACME

ACME Color Par 36 Manual de usuario

ACME

ACME Ellipsoidal Manual de usuario

ACME

ACME XP-470 BSW Manual de usuario

ACME

ACME ENERGY HYBRID Manual de usuario

ACME

ACME LED-MS150 Manual de usuario

ACME

ACME LS-608 RGB Manual de usuario

ACME

ACME Theatre LED Colour Flood Manual de usuario

ACME

ACME GLORY PROFILE Manual de usuario

ACME

ACME Stage Blinder P4 Manual de usuario

ACME

ACME E-10T WW DXX Manual de usuario

ACME

ACME Color Spot Manual de usuario

ACME

ACME Stage Panel 1080 Manual de usuario

ACME

ACME WHACK XP-231 BEAM Manual de usuario

ACME

ACME iColorLed 18TC Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario