ACME XA-500 Manual de usuario

XA-500 FRAMING

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instructions............................................................................................................................2

2. Technical Specifications....................................................................................................................3

3. How To Set The Unit.........................................................................................................................4

3.1 Control panel..................................................................................................................................4

3.2 Main Function ................................................................................................................................4

3.3 Home Position Adjustment ..........................................................................................................10

4. Control By Universal DMX Controller.............................................................................................12

4.1 DMX Connection ..........................................................................................................................12

4.2 Address Setting.............................................................................................................................13

4.3 DMX 512 Configuration................................................................................................................13

5. Troubleshooting .............................................................................................................................19

6. Fixture Cleaning .............................................................................................................................20

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read carefully the instruction, which includes

important information about the installation, usage and

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specifications

DMX Channels: 29/31 channel mode

Blue LCD display for easy navigation

Perfect for stage, theatre, TV studio, rental and discotheques

Voltage:

Power consumption:

LED:

Fuse:

Beam Angle:

Dimension:

Weight:

AC 100V~240V,50/60Hz

620W

1 x 440W White LED

T15A

14°-35°

447 x 423 x 722mm

32Kgs

3. How To Set The Unit

3.1 Control panel

1. Function Display: Used to show the various menus and the selected function;

2. Button:

To select the programming functions

To go forward in the selected functions

DOWN

To go backward in the selected functions

ENTER

To confirm the selected functions

3. DMX IN/OUT: DMX 512 link, use XLR cable to link the unit and DMX controller;

4. POWER IN: Connect to power supply.

5. POWER WITCH: Turn on/off the power;

6. FUSE (T15Amp): Protect the unit from damage of the overcurrent;

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by the ENTER button and the display will blink. Use the

DOWN and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

The main functions are showing below:

DMX Functions

512

Display Setting

Reset Functions

Yes

No/Yes

1~10

Special Functions

Fixture Settings

Fixture Information

Fixture Test

No/Yes

29 CH

31 CH

quare Law

nv SQ Law

iner

Curve

Yes

ear

°°CF/

DMX Settings

To select DMX Settings press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address or Channel Mod.

DMX Address —DMX512 address setting

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to

adjust the address from 001 to 512, press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button

to select 20 CH or 31 CH, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle one minute to exit menu mode

Fixture Settings

To select Fixture Settings, press the ENTER button to confirm, use the UP/DOWN button to select

Pan Inverse, Tile Inverse, P/T Feedback, Focus Compensate BL.O. P/T Moving, BL.O. Color

Change,BL.O. Gobo Change, Dimmer Speed or Dimmer Curve.

Pan Inverse

To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select

No (normal) or Yes (pan inverse), press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle one minute to exit menu mode.

Tilt Inverse

To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select

No (normal) or Yes (tilt inverse), press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle one minute to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to

select No (Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while

pan/tilt out of step), press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle one minute to exit menu mode.

Focus Compensate

To select Focus Compensate, press the ENTER button to confirm. Use the UP/DOWN button

to select Disable, Near, Medium or Far, press the ENTER button to store. Press the MENU

button back to the last menu or let the unit idle one minute to exit menu mode.

BL.O. P/T Moving —Blackout while pan/tilt moving

To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to

select No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

BL.O. Color Change — Blackout while change color

To select BL.O. Color Change, press the ENTER button to confirm. Use UP/DOWN button to

select No (normal while changing color) or Yes (blackout while change color), press the ENTER

button to store. Press the MENU button back to the last menu or let the unit idle one minute

to exit menu mode.

BL.O. Gobo Change — Blackout while change gobo

To select BL.O. Gobo Change, press the ENTER button to confirm. Use the UP/DOWN button

to select No (normal while changing gobo) or Yes (blackout while changing gobo), press the

ENTER button to store. Press the MENU button back to the last menu or let the unit idle one

minute to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to confirm. Use the DOWN/UP button to

select the Square, Inv SQ Law, Linear or S Curve. Once the mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU

button again. Press and hold the MENU button about one second or wait for one minute to

exit the menu mode.

Optically Linear:

The increase in light intensity appears to be linear as DMX value is increased.

Square Law:

Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law:

Light intensity control is coarser at low levels and finger at high levels.

S-cure:

Light intensity control is finger at low levels and high levels and coarser at medium levels.

Display Settings

Enter menu mode, select Display Setting, press the ENTER button to confirm, use the

UP/DOWN button to select Display Inverse, Backlight Intensity, Temperature Unit.

Display Inverse

Select Display Inverse, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select No (normal display) or Yes (inverse display), press

the ENTER button to store. Press the MENU button back to the last menu or let the unit idle

one minute to exit menu mode.

Backlight Auto Off

Select Backlight Auto Off, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select No or Yes, press the ENTER button to store. Press

the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Backlight Intensity

Select Backlight Intensity, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to adjust backlight intensity from 1 (dark) to 10 (bright),

press the ENTER button to store. Press the MENU button back to the last menu or let the unit

idle one minute to exit menu mode.

Temperature Unit

Select Temperature Unit, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to select

℃

℉

, press the ENTER button to store. Press

the MENU button back to the last menu or let the unit idle one minute to exit menu mode.

F ixture Test

Enter menu mode, select Fixture Test, press the ENTER button to confirm, use the UP/DOWN

button to select Auto Test or Manual Test

Auto Test

Select Auto Test, press the ENTER button to confirm, the unit will run built-in programs to

automatically test pan, tilt, shutter, color, CMY, gobo, gobo rotation, prism, prism rotation, iris,

frost, zoom, focus, dimmer and lamp on/off. Press the MENU button back to the last menu or

exit menu mode after auto test.

Manual Test

Select Manual Test, press the ENTER button to confirm, the present channel will show on the

display, use the UP/DOWN button to select channel, press the ENTER button to confirm, then

use the UP and DOWN button to adjust the value, press the ENTER button to store, the fixture

will run as the channel value indicates. Press the MENU button back to the last menu or exit

menu mode idling one minute.

(All channels value will become 0 after exiting Manual Test menu)

Fixture Information

Enter menu mode, select Fixture Information, press the ENTER button to confirm, use the

UP/DOWN button to select Fixture use hour, Temperature or Firmware Version.

Fixture use hour

Select Fixture use hour, press the ENTER button to confirm, fixture use time will show on the

display, press the MENU button to exit.

Temperature

Select Temperature, press the ENTER button to confirm, fixture temperature will show on the

display, press the MENU button to exit.

Firmware Version

Select Firmware Version, press the ENTER button to confirm, firmware version will show on

the display, press the MENU button back to exit.

Reset Functions

Enter menu mode, select Reset Function, press the ENTERbutton to confirm, use the

Tabla de contenidos

Otros manuales de Equipo de DJ de ACME

ACME

ACME LP-TS200 CW Manual de usuario

ACME

ACME SAM-50 Manual de usuario

ACME

ACME LED-ST1000 Manual de usuario

ACME

ACME MH-575S Manual de usuario

ACME

ACME ASTRO LED-256D Manual de usuario

ACME

ACME LED-MTX25 IP Manual de usuario

ACME

ACME LED-245 II Manual de usuario

ACME

ACME Ellipsoidal E-300 D2550 Manual de usuario

ACME

ACME MACE Manual de usuario

ACME

ACME LS-608 RGB Manual de usuario

ACME

ACME iMove 50SR Manual de usuario

ACME

ACME 04XOZONE Manual de usuario

ACME

ACME GLORY PROFILE Manual de usuario

ACME

ACME MH-640S-ELC Manual de usuario

ACME

ACME LED-MS150 Manual de usuario

ACME

ACME WHACK XP-231 BEAM Manual de usuario

ACME

ACME MINI ELLIPSOIDAL 10 Manual de usuario

ACME

ACME MP-400Z IP Manual de usuario

ACME

ACME ORION XP-260 BEAM Manual de usuario

ACME

ACME ELLIPSOIDAL E-300 Manual de usuario

ACME

ACME BLINDER LINE 10 IP Manual de usuario

ACME

ACME PAGEANT 300ZR Manual de usuario

ACME

ACME XP-1000WZ Manual de usuario

ACME

ACME Stage Blinder P4 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario