ACME LED WAVE 100 Manual de usuario

LED-WAV-100W

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instruction................................................................................... 2

2. Technical Specification ........................................................................... 3

3. How To Set The Unit............................................................................... 4

3.1 Control Panel ................................................................................... 4

3.2 Lens Installation ............................................................................... 5

3.3 Main Function.................................................................................. 6

4. How To Control The Unit ...................................................................... 10

4.1 Master/Slave Built In Preprogrammed Function ............................ 10

4.2 Easy Controller ............................................................................... 10

4.3 DMX Controller .............................................................................. 11

4.4 DMX 512 Configuration.................................................................. 11

4.5 DMX512 Connection ...................................................................... 12

5. Troubleshooting ................................................................................... 13

6. Fixture Cleaning ................................................................................... 14

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 75℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any cables during operation as high voltage may cause electric shock.

Please read this instruction carefully which includes important

information about the installation, usage and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

The unit should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Also always use a safety cable that can hold 12 times of the weight of the unit

when installing the fixture.

The equipment must be installed by professionals. It must be installed in a place where is out of

the reach of people and no one can pass by or under it.

2. Technical Specification

◇The “high power” LED Water wave effect, based on a 100W LED, is suitable for big clubs, stages,

and events

◇Different working modes:

Standalone: no DMX-controller needed

Master/Slave: great synchronized shows, no DMX-controller required

DMX:3 channels (dimmer, speed, color)

◇Color wheel with 5 colors plus open

◇Two different beam angles (standard 44°or 29°)available

◇LED display for easy navigation

◇High efficiency and low power consumption

◇Input Voltage:AC 100V~240V, 50/60Hz

◇Power Consumption: 105W

◇Light Source: 1 x 100W cold white LED

◇Weight: 6.2Kgs

◇Dimension: 309 x 271 x 210 mm

3. How To Set The Unit

3.1 Control Panel

1. Only for remote control:

Connects to optional CA-8 to control the unit in Stand by, Function and Strobe/Blackout modes.

2. DMX IN:

DMX512 link, use 3-pin XLR cable to link the unit and the DMX controller

3. DMX OUT:

DMX512 link, use 3-pin XLR cable to link the next unit and output DMX signal.

4. Fuse (T 3.15A):

Protects the unit from over-voltage or short circuit.

5. MAINS IN:

Connection from main power supply;

6. MAINS OUT:

Connection for main power supply to the next unit.

7. LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

8. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

9. Function Display:

To show the various menus and the selected functions;

3.2 Lens Installation

A. Product Items

User manual

29°lens

B. Mounting

You can install the unit on the truss or ceiling; Use clamps to fix the unit to truss. Always ensure

that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure. Also always use a safety cable that can hold

10 times of the weight of the unit when installing the fixture.

C. Replace the lens

You could replace the other lens if you want to, as following picture.

You should screw the lens roller to take it down as NO.1, and bring the lens out as No.2. Then you

could replace the lens that you want to.

Notes: the lens roller has two slots for the lens; you should pay more attention that the latest slot

is for the 29°lens, and the far slot is for 44°lens.

3.3 Main Function

To select any of the given functions, press the MENU button up to when the required selection as

shown on the display. Select the function by the ENTER button and the display will blink. Use the

DOWN/UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Press and hold the MENU button for about one second or wait for one minute to exit the

menu mode.

The main functions are shown below:

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the

address has been selected, press ENTER button to setup or automatically exit menu mode without

any change after one minute. Back to the previous functions without any change press MENU

button.

Show Mode

Press the MENU button up to when the is showing on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select the (Random show),

(show 1) or (show 2). Once the mode has been selected, press the ENTER button to setup

or automatically return to the main functions without any change after one minute. To go back to

the functions without any change press the MENU button again.

Slave Mode

Press the MENU button up to when the is showing on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select the (set the fixture as

master) , (set the fixture as slave 1) or (set the fixture as slave 2). Once the mode

has been selected, press the ENTER button to setup or automatically return to the main functions

without any change after one minute. To go back to the functions without any change press the

MENU button again.

Display Inverse

Press MENU button until is blinking on the display. Use DOWN and UP button to select

(display normal) or (display inverse), press ENTER button to setup.

LED display

Press the MENU button up to when the is shown on the display. Pressing ENTER button

and the display will blink. Use DOWN and UP button to select (display always on) or

(display off 20 seconds after exit menu) mode. Once select, press ENTER button to setup or

exit menu mode without any change after one minute. Back to the functions without any change

press MENU button again.

Manual setting color

Press the MENU button up to when the is shown on the display. Pressing ENTER button,

and use DOWN and UP button to select (0-255) or

(000-2555,clockwise/counterclockwise) , or (000-255),press ENTER button to confirm and

use DOWN and UP button to adjust the value, once select press ENTER button to setup or

automatically exit menu mode without any change after one minute. To go back to the last

function without any change press the MENU button.

Self-test

Press the MENU button up to when the is shown on the display, Pressing ENTER button to

run the auto test. Back to the functions without any change press MENU button.

Back to the functions without any change press MENU button.

Temperature Test

Press the MENU button up to when the is blinking on the display. Pressing ENTER button

and the display will show the temperature of the unit. To go back to the functions press the MENU

button again.

Fixture Hours

Press the MENU button up to when the is blinking on the display. Pressing ENTER button

and the display will show the number of working hours of the unit. To go back to the functions

press the MENU button.

Software version

Press the MENU button up to when the is showing on the display. Pressing ENTER button

and the display will show the version of software of the unit. To go back to the functions press the

MENU button again.

Factory reset all channels

Press the MENU button up to when the is shown on the display, press ENTER button to

Otros manuales para LED WAVE 100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de ACME

ACME

ACME XA-500 Manual de usuario

ACME

ACME ENERGY SPOT XA-400 SPOT Manual de usuario

ACME

ACME O2 Oxygen Manual de usuario

ACME

ACME CYC-200 FC Manual de usuario

ACME

ACME LED-Exercet Manual de usuario

ACME

ACME LED-BR10 Manual de usuario

ACME

ACME Junior Series Manual de usuario

ACME

ACME Stage Blinder P4 Manual de usuario

ACME

ACME PAGEANT 300ZR Manual de usuario

ACME

ACME Festival LED-787 Manual de usuario

ACME

ACME LED-920D Manual de usuario

ACME

ACME CA-DD12 II Manual de usuario

ACME

ACME Spartan Hybrid Manual de usuario

ACME

ACME MH-575S Manual de usuario

ACME

ACME 04XOZONE Manual de usuario

ACME

ACME LED-747-1W Manual de usuario

ACME

ACME VENOM LED-460 Manual de usuario

ACME

ACME CW-108 Manual de usuario

ACME

ACME MP-90 RGBW Manual de usuario

ACME

ACME LED-737 Manual de usuario

ACME

ACME LED-MS50A Manual de usuario

ACME

ACME LED-BL4B Manual de usuario

ACME

ACME THUNDERBOLT Manual de usuario

ACME

ACME AE-610 BEAM Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario