ZKTeco ProBio Manual de usuario

QUICK START GUIDE

ProBio

Version: 1.2

Date: September 2021

Safety Precautions

Before installation, please read the following safety precautions for user

safety and to prevent product damage.

Do not install the device in a place subject to direct sun light, humidity, dust

or soot.

Do not place a magnet near the product. Magnetic objects such as magnet,

CRT, TV, monitor or speaker may damage the device.

Do not place the device next to heating equipment.

Do not to let liquid like water, drinks or chemicals leak inside the device.

Do not let children touch the device without supervision.

Do not drop or damage the device.

Do not disassemble, repair or alter the device.

Do not use the device for any purpose other than those specified.

Clean the device often to remove dust on it. In cleaning, do not splash water

on the device but wipe it out with smooth cloth or towel.

Contact your supplier in case of a problem!

Cautions on Using Face Recognition Device

1) Recommended Standing Position

a. Recommended Registration and Verification Position

b. Factors Affecting the Preciseness of Verification

For user heights between 1

.5m to 1.8m, it is recommended to

install the device at 1

.15m above ground (may be modified

according to user average height)

Recommended Procedure

s (as shown in the left

image):

During registration and verification procedures, the

position of device should

not be changed to

prevent deduction

in verification preciseness. If it is

necessary to move the device, its vertical height

should not be changed.

Non-identical registration and verification

gestures

Non-identical registration and verification

heights

Non-identical registration and verification

distance

s from device

Non-identical registration and verification

distance

s from device

2) Registration

a. During registration, it is required to adjust your upper body to fit your eyes into the

green frame on the screen.

b. During verification, it is required to show your face in the center of the screen and fit

your face into the green frame in the screen.

Device Overview



Not all products have fingerprint or card function, the real product

shall prevail.



ProBio

Front Left Side

USB Slot

Reset Button

Touch Screen

Doorbell

Camera

Fingerprint Reader

& Card Reader Area

Product Dimensions & Installation



Product Dimensions

Mounting the Device on Wall

Power Conne

7.51 in

(190.8 mm)

3.35 in

(85 mm)

4.05 in

(103 mm)

5.08 in

(129 mm)

2.4 in

(61 mm)

Fix the back plate onto the wall using wall mounting screws.

Insert the device into back plate. Use security screws to fasten

the device to back plate.

Put the mounting template sticker onto the wall, and drill holes

according to the mounting paper.

1.15m

Power Connection

Without UPS

With UPS (Optional)

Recommended Power Supply

GND

12V DC

12V DC Adaptor

GND

12V DC

12V DC Adaptor

12V±10%, at least 500mA (12V /3A is standard).

To share the power with other devices, use a power supply with higher

current ratings.

Ethernet Connection

LAN Connection

Network Cable Adaptor

Ethernet Cable

Note: The device can be connected to PC directly by Ethernet cable.

RS485 Connection

RS485 Fingerprint Reader Connection

DIP Settings

1. There are six DIP switches on the back of RS485 fingerprint reader,

switches 1-4 are for RS485 address, switch 5 is reserved, switch 6 is for

reducing noise on long RS485 cable.

2. If RS485 fingerprint reader is powered from the terminal, the length of

wire should be less than 100 meters or 330 ft.

3. If the cable length is more than 200 meters or 600 ft., the number 6

switch should be ON as below.

RS485 Fingerprint Reader

Lock Relay Connection

Device Not Sharing Power with the Lock

COM1 12V DC

GND

Sensor NC1

FR107 Diode

12V DC Adaptor

Normally Closed Lock

Notes:

1. The system supports NO LOCK and NC LOCK. For example the NO

LOCK (normally opened at power on) is connected with 'NO1' and

'COM1' terminals, and the NC LOCK (normally closed at power on) is

connected with 'NC1'and 'COM1' terminals.

2. When electrical lock is connected to the Access Control System, you

must parallel one FR107 diode (equipped in the package) to prevent

the self-inductance EMF from affecting the system.

Do not reverse the polarities.

GND

Lock Relay Connection

Device Sharing Power with the Lock

COM1

12V DC

GND

Sensor

NC1

FR107 Diode

Normally Closed Lock

GND

Otros manuales para ProBio

Tabla de contenidos

Otros manuales de Controladores de acceso IP de ZKTeco

ZKTeco

ZKTeco MultiBio 700 Manual de usuario

ZKTeco

ZKTeco X7 Manual de usuario

ZKTeco

ZKTeco FaceDepot-7BL Manual de usuario

ZKTeco

ZKTeco MiniAC Plus Manual de usuario

ZKTeco

ZKTeco FR1200 Manual de usuario

ZKTeco

ZKTeco C2-260/inBio2-260 Manual de usuario

ZKTeco

ZKTeco SpeedFace-V3L Manual de usuario

ZKTeco

ZKTeco MA500 Guía de solución de problemas

ZKTeco

ZKTeco FA50 Manual de usuario

ZKTeco

ZKTeco Ultima Series Manual de usuario

ZKTeco

ZKTeco PA10 Manual de usuario

ZKTeco

ZKTeco TF1600 ZKTeco Manual de usuario

ZKTeco

ZKTeco VF Series Manual de usuario

ZKTeco

ZKTeco SF1005-V+ Manual de usuario

ZKTeco

ZKTeco MB10-VL Manual de usuario

ZKTeco

ZKTeco ProlD Series Manual de usuario

ZKTeco

ZKTeco inBIO 480 Guía

ZKTeco

ZKTeco C3 Pro Manual de usuario

ZKTeco

ZKTeco LF10 Manual de usuario

ZKTeco

ZKTeco ZKX5030A Manual de usuario

ZKTeco

ZKTeco F18 Manual de usuario

ZKTeco

ZKTeco OP-200 Manual de usuario

ZKTeco

ZKTeco Horus Manual de usuario

ZKTeco

ZKTeco SC800 Manual de usuario

Manuales populares de Controladores de acceso IP de otras marcas

Jantar

Jantar REX A-1-9 Manual de usuario

2N Access Unit Hoja de instrucciones

Kedacom

Kedacom KSCA120 Series Manual de usuario

H3C

H3C WX2880X Manual de usuario

G4S

G4S S870-EX Guía

PRASTEL

PRASTEL M2000PE Manual de usuario

Allegion

Allegion interflex IF-281 Cylinder Manual de usuario

TECOM

TECOM TS1067E Manual de usuario

Fermax

Fermax Memokey 100C Guía del usuario

Fermax

Fermax CITYLINE MEMOKEY Manual de instrucciones

Software House

Software House iSTAR Pro 2U RM Manual de instrucciones

AKCP

AKCP SP+ Manual de usuario

Bpt

Bpt HNA/102 Manual de usuario

Civintec

Civintec CV9601T-T-1F Manual de usuario

BioMax

BioMax N-X90W Manual de usuario

FingerTec

FingerTec s-Kadex Manual de usuario

H3C

H3C WX5002ACCESSCONTROLLER Manual de usuario

C Prox Ltd

C Prox Ltd DPN-2 Manual de usuario