ZKTeco X6 Hoja de instrucciones
X6 CONFIGURATION MANUAL
Default Program Password : 1234 maximum finger : 500
CREATE ADMIN
exit (green light on and a long buzz)
CHANGE ADMIN
FORGOT ADMINISTRATOR PASSWORD
If the administrator password is lost, you can reset the password to default by using tamper switch.
Operation:
1. Dismantle the device and wait for 30 seconds until a short beep is heard.
2. Press the Tamper Switch thrice to reset to the initial administrator password.
This operation must be done within 30 seconds; the default administrator password is 1234.
ADD/EDITUSER (finger)
Each user can resist 10 fingerprint and 1 card at most
Px)
continue to add new users OR press [*] to escape(green light on
and a long buzz)
ADD CARD
Pmax) card 2 times
long buzz)
ADD PASSWORD
The machine support at most 8groups of door password,
-
Note:
A. When a group of password was changed into 00000, then this group of password was shut down
B. When a group of password was changed successfully, you can input next group of number to modify
directly.
OPEN DOOR BY PASSWORD
Enter password and press # for verification
DELETE SINGLE USER
fingDelete all of the users
DELETE ALL USER
DOOR UNLOCK DURATION
Default: 6 second
CONFIGURE ATHENTICATION MODE (FP/PW/RF)
Mode
Value
Description
PW
1
Only Password
RF
2
Only Card
FP
3
Only fingerprint
FP/PW/RF
4
Fingerprint or password or card
RF& PW
5
Card then password
FP & PW
6
Fingerprint them password
CONFIGURE ALARM
Alarm Switch (Default ON) The switch is the master switch of the machine, only when it's on, can the alarm
incorrectly, tamper alarm and magnet alarm be working properly. The alarm will be shut down when it's
TAMPER ALARM CONFIGURE (Default ON)
Buttons represent: [#] means yes, [*] means Escape
Lights represent: Green means success, Red means Failure
Number: Password=4 digits, work code<=5 digits
Tones: Long buzz means success, short buzz twice means failure, short buzz 4 times means
wrong action Notice: make sure you pressed [#] to confirm, [*] exit
Tabla de contenidos
Otros manuales de Controladores de acceso IP de ZKTeco
ZKTeco
ZKTeco SpeedFace-V3L Manual de usuario
ZKTeco
ZKTeco inBIO 480 Guía
ZKTeco
ZKTeco KF1000-U Manual de usuario
ZKTeco
ZKTeco BioPro SA50 Manual de usuario
ZKTeco
ZKTeco BioServer 2 Manual de usuario
ZKTeco
ZKTeco F18 Manual de usuario
ZKTeco
ZKTeco FA50 Manual de usuario
ZKTeco
ZKTeco X8-BT Manual de usuario
ZKTeco
ZKTeco MA500 Guía de solución de problemas
ZKTeco
ZKTeco P160 Manual de usuario
ZKTeco
ZKTeco ProCapture-WP Manual de usuario
ZKTeco
ZKTeco OP-200 Manual de usuario
ZKTeco
ZKTeco C3 Pro Manual de usuario
ZKTeco
ZKTeco BioPro SA30 Manual de usuario
ZKTeco
ZKTeco ProMA Series Manual de usuario
ZKTeco
ZKTeco ProlD Series Manual de usuario
![ZKTeco G4[QR] Manual de usuario](/data/manuals/1j/2/1j2wo/sources/zkteco-g4-qr-ip-access-controllers-manual.jpg "ZKTeco G4[QR] Manual de usuario")
ZKTeco
ZKTeco G4[QR] Manual de usuario
ZKTeco
ZKTeco ZKX5030A Manual de usuario
ZKTeco
ZKTeco MultiBio 700 Manual de usuario
ZKTeco
ZKTeco SpeedFace-V5L Manual de usuario
