Wilson Electronics WilsonPro A1000 Manual de usuario
NEED HELP? boltontechnical.co.za 011 749 3085
User Manual
Cellular Signal Booster
WilsonPro A1000
Package Contents 1
STEP 1: Preparation 2
STEP 2: Find The dBm Reading On Your Phone 3
STEP 3: Measure Signal Strength For Inside Antenna 4
STEP 4: Measure Signal Strength For Outside Antenna 5
STEP 5: Temporarily Mount The Outside Antenna 6
STEP 6: Connect The System 7
STEP 7: Compare Results 8
STEP 8: Permanently Mount The Outside Antenna 9
STEP 9: Permanently Mount The Inside Antenna 11
STEP 10: Route & Secure The Cable 12
Test System: Lights 13
Specifications 15
Safety Guidelines 16
Warranty 18
______
Index
WilsonPro A1000 CELL PHONE SIGNAL BOOSTER 1
________
Package
Contents
WilsonPro
A1000
2x Pole Mount
Bracket
Wall Mount
Bracket
Inside
Antenna
Power
Supply
This device may be operated ONLY in a fixed location for in-building
use. The signal booster unit is designed for use in an indoor,
temperature controlled environment (38 degrees Celsius)
Outside
Antenna
3 Coax Cables
(1m,10m,15m)
Lightning
Surge
Protector
We recommend plugging in the power supply into a power strip to protect against power surges
and installing a lightning surge protector that is earthed.
2CELL PHONE SIGNAL BOOSTER WilsonPro A1000
______
Step 1: Preparation
NOTE: These instructions will walk you through a “soft” install process to find the
optimal locations for the Inside and Outside ntennas, then through the process of the
permanent installation.
You Will Need (tools not included)
Make sure the following materials are prepared and ready for your installation.
o Ladder
o Phillips-head screwdriver
o 10mm open-end wrench or adjustable wrench
o Drill (if routing cable through wall)
o Mounting Option A:25cm diameter pole (#BT512631)
or an existing pole
o Recommended: Power Strip with surge protection
2 to 3 hours
2 people (a person to help with antenna calibration)
WilsonPro A1000 CELL PHONE SIGNAL BOOSTER 3
______
Step 2: Find The dBm
Reading On Your Phone
Put your iPhone into field test mode. To do this dial
*3001#12345#* then press call.
1Hold down power button until you see 'Slide to Power O'.
2Then release the power button.
3 Hold the Home button until your main screen appears.
If you want to check 3G/1x but your iPhone is picking up 4G/
LTE signal, go to Settings>Cellular>Cellular Data Options>Enable
LTE>Select O.
After you system is set up, you can go back to the dots signal
by once again dialing *3001#12345#* then pressing call. When
the menu comes back up, tap “phone” in the top left corner of
your phone.
Settings > About Phone > Status or Network > Signal Strength or
Network Type and Strength (exact options/wording depends on
phone model).
iOS 11 no longer displays the decibel (dBm) reading in ‘Field Test
Mode’. Tip: Using the bar indicator on your cell phone can assist
you in finding the strongest signal direction as well as placing
calls in dierent locations. For changes/updates on this issue,
periodically go to:
www.boltontechnical.co.za/blogs/news/signalstrength
iPhone®
iOS 9 - 10.3.3
iPhone®
iOS 11 - current
Android™
iPhone is a registered trademark of Apple Inc. Android is a trademark of Google Inc.
All Other Phones & Alternate Methods
iPhone
• OpenSignal is a free app that allows you to run a test of your iPhone’s
true speed
• Speedtest by Ookla is another free app
Android users: do a signal strength test and network speed test.
• Network Cell Info Lite, available for free on the Google Play store, provides
nearly real-time monitoring of cellular and WiFi signals
Visit: https://www.boltontechnical.co.za/blogs/news/signalstrength
4CELL PHONE SIGNAL BOOSTER WilsonPro A1000
______
Step 3: Measure Signal
Strength For Inside
Antenna Placement
Having an accurate measurement of signal strength in decibels (dBm) is crucial
when installing your system. Decibels accurately measure the signal strength you
are receiving. Test both 3G and 4G signal for best results by turning the LTE o in
the carrier settings of your device.
SIGNAL STRENGTH EXCELLENT GOOD FAIR POOR DEAD ZONE
3G/1x
(typically voice) -70dBm -71 to -85dBm -86 to -100dBm -101 to -109dBm -110dBm
4G/LTE
(typically data) -90dBm -91 to -105dBm -106 to -110dBm -111 to -119dBm -120dBm
Turn o your cell phone’s WiFi to ensure you
are checking the cellular connection. The dBm
reading will be refreshed every 30-60 seconds.
Want faster results? Once you have a reading,
turn on airplane mode. Wait 15 seconds.
Turn o airplane mode. The signal strength
reading is refreshed.
Walk around your home/oce taking signal
strength readings until you find the area that has
the weakest reception, or number farthest away
from zero. For example -100 is a weaker signal
than -80.
Users on iOS 11 and above will need to use an
alternative method using the bar indicator on
your cell phone and/or placing calls in dierent
locations.
Weakest Signal Number:___________
Weakest Signal Location: ___________
Place your Inside Antenna in this poor signal area.
For best results, keep the Inside Antenna more
than 45cm away from the booster.
WilsonPro A1000 CELL PHONE SIGNAL BOOSTER 5
______
Step 4: Measure Signal
Strength For Outside
Antenna Placement
This is the most critical step of the installation
process because it will determine the overall
performance of the booster system. Using the
same method as Step 3, find the place with the
strongest signal (number closest to zero) on the
outside of your home.
Users on iOS 11 and above will need to use an
alternative method using the bar indicator on
your cell phone and/or placing calls in dierent
locations.
The further apart the Inside Antenna is located
from the Outside Antenna, the better. To
determine the best location for your Outside
Antenna, note the dBm reading in a variety of
locations.
Note: The Outside Antenna must be at least
6 meters vertical or 15 meters horizontal from
the Inside Antenna for best performance. Make
sure the Inside Antenna and Outside Antennas
are facing away from each other.
6CELL PHONE SIGNAL BOOSTER WilsonPro A1000
______
Step 5: Temporarily Mount
The Outside Antenna
Use one of the two options to mount the
Outside Antenna on the side of the house with
the strongest signal.
Note: Using an app like 'Open Signal' will help
you point the Outside ntenna in the direction
of the nearest cell phone tower.
AOption (Best)
BOption (Good)
Note: The Outside Antenna must be at least
6 meters vertical or 15 meters horizontal from
the Inside Antenna for best performance. Make
sure the Inside Antenna and Outside Antennas
are facing away from each other.
A
B
WilsonPro A1000 CELL PHONE SIGNAL BOOSTER 7
Band 5 Band 4
Band 12/13/17
Connect 4G-X ®
Band 2
Band 5 Band 4
Band 12/13/17
Connect 4G-X ®
Band 2
______
Step 6: Connect The System
2
Connect the supplied Coax Cable to end of
booster labeled Inside Antenna.
3
Power up the Booster by connecting it to a
power source.
To protect Booster from power surges, connect
to a power strip.
1
Connect the supplied Coax Cable to end of
booster labeled Outside Antenna.
Outside
Antenna
Inside
Antenna
Warning: Do Not connect power
supply to booster before connecting
both outside and indoor antennas
Band 5 Band 4
Band 12/13/17
Connect 4G-X ®
Band 2
Band 5 Band 4
Band 12/13/17
Connect 4G-X ®
Band 2
8CELL PHONE SIGNAL BOOSTER WilsonPro A1000
______
Step 7: Compare Results
Using the field test mode described in step 3, measure the new signal
strength and write it down here ___________.
Compare this number with the original reading you took in the same part of the house.
If the number is higher (closer to zero) than the original reading without booster, your
booster is working. If it is not, look at the lights on the booster and the section at the
end of this manual “Test System: Lights”.
Users on iOS 11 and above will need to use an alternative method using the bar
indicator on your cell phone and/or placing calls in dierent locations.
Did you know a signal increase in just
3dB is 2 times the power and signal amplification!
Distance from Cell Tower
CELL
TOWER
Signal Strength
GOOD
Signal Strength
POOR
Signal Strength
DEAD ZONE
Signal Strength
EXCELLENT
Signal Strength
FAIR
3G/1x
4G/LTE
-70dBm
-90dBm
-75dBm
-100dBm
-90dBm
-108dBm
-105dBm
-115dBm
-110dBm
-120dBm
DECIBEL GAIN POWER INCREASE
3dB 2 times the power and signal amplification
6dB 4 times the power and signal amplification
10dB 10 times the power and signal amplification
12dB 16 times the power and signal amplification
20dB 100 times the power and signal amplification
Tabla de contenidos
Otros manuales de Extensor de Wilson Electronics
Wilson Electronics
Wilson Electronics Tri-Band 4G-C Manual de usuario
Wilson Electronics
Wilson Electronics Mobile 4G SmarTech III 460108 Manual de usuario
Wilson Electronics
Wilson Electronics weBoost DRIVE X 475021R Manual de usuario
Wilson Electronics
Wilson Electronics weboost Home Complete 530045 Manual de usuario
Wilson Electronics
Wilson Electronics 801105 Manual de usuario
Wilson Electronics
Wilson Electronics WILSON PRO 1050 Manual de usuario
Wilson Electronics
Wilson Electronics AG Pro 75 Manual de usuario
Wilson Electronics
Wilson Electronics WeBoost Drive Reach Flex Fleet Manual de usuario
Wilson Electronics
Wilson Electronics MobileMaxx 3G 460011 Manual de usuario
Wilson Electronics
Wilson Electronics WEBOOST DRIVE X OTR Manual de usuario
Wilson Electronics
Wilson Electronics PRO 1100 Manual de usuario
Wilson Electronics
Wilson Electronics Mobile 4G 460021 Manual de usuario
Wilson Electronics
Wilson Electronics weBoost Drive Reach RV Manual de usuario
Wilson Electronics
Wilson Electronics weboost DRIVE REACH OTR FLEET Manual de usuario
Wilson Electronics
Wilson Electronics weBoost Drive Reach RV Guía de instalación
Wilson Electronics
Wilson Electronics DT4G 460101 Manual de usuario
Wilson Electronics
Wilson Electronics SLEEK 2B5225 Manual de usuario
Wilson Electronics
Wilson Electronics weboost DRIVE REACH Manual de usuario
Wilson Electronics
Wilson Electronics SLEEK 2B5225 Manual de usuario
Wilson Electronics
Wilson Electronics Tri-Band 4G-V Manual de usuario
