VMP LCD-MID-FT Manual de usuario

For more information, please contact us at:

325 Log Canoe Circle, Stevensville, Maryland 21666

(T) 410.643.6390 / (F) 410.643.6615

www.videomount.com

VIDEO MOUNT PRODUCTS

Instruction Sheet For:

LCD-MID-FT & LCD-MID-FTB

Step 1

Before starting, lay out all parts to your mount and match them to

the parts list provided. Verify that you have all your parts before at-

tempting to assemble the mount.

Step 2

Mark the wall or desired mounting surface in preparation of installa-

tion of the wall plate . Pre-drill in necessary and mount the wall

plate to the desired mounting surface.

Warning: Please verify that your mounting surface will support the

combined weight of your mount, mounting hardware, and moni-

tor. Also verify that the mounting surface is safe to drill through. If in

doubt, please contact a professional installer.

Step 3

Determine the correct screw size and if you need to use washers,

lock washers, or spacers. Note: Spacers are used for TVs with re-

cessed hole patterns. Secure the display to the screen mount brack-

et using the appropriate hardware through . Note:

The brackets have to be level with each other to work properly.

Step 2: Mounting the wall plate

(Lag screws are not included)

Step 3A: Attaching the mounting

brackets to the screen

(spacers not needed)

Step 3B: Attaching the mounting

brackets to the screen

(spacers used due to recessed

hole patterns)

VIDEO MOUNT PRODUCTS

1

25

11

3

1

Step 4: Adjusting the tilt tension

before placing the screen on

the wall

Step 4

Adjust the tilt tension by tightening the socket head screws with

the M5 Allen Key so they are fairly tight. Note: You may have

to adjust the tilt tension once the ﬂat screen is on the wall so do not

tighten as hard as you can because it will make further adjustment

on the wall much more difﬁcult.

Step 5

Use the hooks on the pivot bracket to hook on the top rail of the

wall plate . Use the M5 screws to secure the TV to the wall

plate and to secure its horizontal position.

Step 6

If you need to adjust the tilt tension:

Tilt down the ﬂat screen as far as it will go. Note: This is done to give

you room to work with behind the ﬂat screen. Take the M5 Allen Key

and tighten down the socket screws until you have

achieved the desired tilt tension and readjust the tilt to the desired

angle.

Please verify that all nuts and screws are securely tightened.

Step 5: Securing the pivot

brackets to the wall plate

Step 6: Adjusting the tilt tension

after placing the screen

on the wall

WARNING: The installer of these products must verify that the mount-

ing surface, ceiling or wall, will safely support the combined weight

of all attached equipment and hardware. Video Mount Products will

not be held liable for the improper use or installation of its products.

Enjoy Your Mount!

4

9

1

2

1

10

4

10

VIDEO MOUNT PRODUCTS

Este manual sirve para los siguientes modelos

1

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario