VMP LCD-1C Manual de usuario

325 Log Canoe Circle • Stevensville MD 21666 • www.videomount.com

Phone: 410.643.6390 • Fax: 410.643.6615

LCD-1C

1. Before starting lay out all parts to

your mount and match them to the parts

list provided. Verify that you have all

your parts before attempting to assemble

the mount.

2. Next determine which VESA

standard plate you will be using (#5 or

#6) (75mm or 100mm respectively) and

attach the selected mounting plate (#5 or

#6) to the monitor to the swivel bracket

(#4) using the M6 screw that’s about 1.4

inches long (#9) and the nylon nut (#7).

Insert adjustable screw (#12) for use

when tilting the monitor. (Set this

assembly safely to the side for now.)

3. Mark the ceiling or desired mounting

surface in preparation of installation of

ceiling plate (#1). Pre-drill if necessary and

mount the ceiling plate (#1) to desired

surface. Warning: Please verify that your

mounting surface will support the combined

weight of your mount, mounting hardware,

and monitor. Also verify that the mounting

surface is safe to drill through. If in doubt

about either please contact a professional

installer.

4. Next attach the swivel bracket (#4) to the

support tube (#3) using the 3/8” screw that is 2”

long (#16), washers (#15) and nylon nut (#8).

Step 2 : Attaching the mounting

plate to the swivel bracket

Step 3 : Attaching

the ceiling plate to

the ceiling.

Step 4 : Attaching the swivel

bracket to the support tube.

5. Now attach the support tube (#3) to the extension

tube (#2) using the M12 screw that’s about 2.6” long (#10)

and washers (#11).

6. Attach the mounting plate (#5 or #6) to your LCD monitor using the M4 or M5

screws (#21 or #22) as appropriate.

7. Attach the extension tube (#2) to the ceiling plate (#1) using

the 5/16” screw 1.5” in length (#18) and nylon nut (#19). Secure

the M12 screw (#10) from slipping in the extension tube (#2) by

tightening the ¼” brake screw (#17) into the threaded hole in the

side of the extension tube (#2) using the Allen key (#20).

8. Insert end plugs (#14) into the support

tube (#3). Insert the cable clips (#13) by

pushing the arrow ends into the square holes in

the force arms. Please verify that all nuts and

screws are securely fastened.

Enjoy your mount!

WARNING: The installer of these products must verify that the mounting surface,

ceiling or wall, will safely support the combined weight of all attached equipment and

hardware. Video Mount Products will not be held liable for the improper use or

installation of its products.

Step 5 : Attaching

the support tube to

the extension tube

Ste

p

6 : Attachin

g

the monitor to the mountin

g

p

late

Step 7 : Connecting

the extension tube to

the ceiling plate

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario