VMP SCFR-1 Manual de usuario

SCFR-1

Instruction Sheet For:

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615

www.videomount.com

Step 1

Before starting, lay out all parts to your mount and match them to

the parts list provided. Verify that you have all your parts before

attempting to assemble the mount.

Step 2

Determine what ceiling mount you are using. If you are using a

PDM-C, LCD-MID-C, PM-LP ceiling mast or 1.5” NPT pipe proceed

to step 3. If you are using a LCD-1C, LCD-2537C, LCD-PV, PV-1,

VMP-014/024, VMP-036/038, VMP-042/044, VMP-046/048, PM-1,

PM-2, PM-3 ceiling mast or 1” NPT pipe proceed to step 5.

If you are using a PDM-C, LCD-MID-C, PM-LP ceiling mast or 1.5”

NPT pipe:

Step 3

Cut a hole for the ceiling mast/pipe to pass through in the ceiling

tile. The easiest way to do this is to take the mast/pipe and trace

around the outside of it on the topside of the ceiling tile. Then pro-

ceed to cut out the ceiling tile within the line.

Step 4

Slide the ceiling mast/pipe through the hole cut into the ceiling tile.

Once you have done this take both halves of the escutcheon ring

and snap them on to the ceiling mast/pipe ﬂush to the ceiling.

Note: Depending on the exact mast your attaching to you may

ﬁnd the ring hard to clamp down. If you do just remove one of the

spring metal pieces from one side of the escutcheon ring to make

it easier.

Step 3: Cutting a hole in

the ceiling tile

Step 4: Attaching the

escutcheon ring

1

Enjoy Your Mount!

If you are using a LCD-1C, LCD-2537C, LCD-PV, PV-1, VMP-

014/024, VMP-036/038, VMP-042/044, VMP-046/048, PM-1, PM-

2, PM-3 ceiling mast or 1” NPT pipe:

Step 5

Cut a hole for the escutcheon ring adaptor . The easiest

way to do this is to take the adaptor and trace around the

outside of the smaller end of the adaptor on the topside of the

ceiling tile. Then proceed to cut out the ceiling tile within the

line.

Step 6

Insert the escutcheon ring adaptor into the ceiling tile mak-

ing sure the ﬂange rest ﬂush on the top of the ceiling tile.

Step 7

Slide the ceiling mast/pipe through the escutcheon ring adap-

tor . Attach both halves of the escutcheon ring to the

escutcheon ring adaptor .

Step 5: Cutting a hole in

the ceiling tile

Step 6: Inserting the adaptor

Step 7: Attaching the

escutcheon ring

WARNING: The installer of these products must verify that

the mounting surface, ceiling or wall, will safely support the

combined weight of all attached equipment and hardware.

Video Mount Products will not be held liable for the improper

use or installation of its products.

Enjoy Your Mount!

2

2

2

21

2

Tabla de contenidos

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario