VMP LCD-1 Manual de usuario

LCD-1 & LCD-1B

Step 1

Before starting, lay out all parts to your mount and match them to

the parts list provided. Verify that you have all your parts before

attempting to assemble the mount.

Step 2

Attach the mounting plate to your LCD monitor using the M4

or M5 screws or as appropriate.

Step 3

Markthewallordesiredmountingsurfaceinpreparationofinstalla-

tion of wall mounting plate . Pre-drill if necessary and mount wall

plate to desired surface. Mount wall plate with small welded

rotation stoppers to the bottom of the plate. Warning: Please verify

that your mounting surface will support the combined weight of

your mount, mounting hardware, and monitor. Also verify that the

mounting surface is safe to drill through. If in doubt, please contact

a professional installer.

Step 4

Next determine which arm conﬁguration you desire (double arm,

single arm, or near ﬂush) and locate the correct arms ( for near

ﬂush, for single arm, OR and for double arm). Attach the

desired wall arm or or to the wall plate using the 3/8”

screw , plastic ﬂanges and nylon nut . Snap the plastic

cover onto the wall plate .

Step 2: Attaching the monitor

to the mounting plate

Step 3: Attaching the wall

plate to the mounting surface

(Lag Screws not included)

Step 4: Attaching the rear

force arm to the wall plate

3

2

11

20

17

2

8

1

5

19

18

1

281

1

6

Step 5

If your application calls for the single arm or near ﬂush mount

conﬁguration proceed to the next step. If your application calls

for the double arm conﬁguration, attach the front force arm )

to the rear force arm using the metal pin , washers )

and the nylon nut .

Step 6

Attach the swivel bracket to the appropriate force arm

( , , or depending on your application) using a 3/8”

screw , washers , and nylon nut . Insert adjustable

screw into the back of the swivel bracket for use when

tilting the monitor.

Step 7

Attach the mounting plate to the swivel bracket using the

M6 screw and nylon nut .

Step 8

Insert end plugs into the force arms used by your application.

Insert the cable clips by pushing the arrow ends into the square

holes in the force arms.

Please verify that all nuts and screws are securely tightened.

Step 5: Attaching the front

force arm to the rear force arm

Step 6: Attaching the pivot

bracket to the front force arm

Step 7: Attaching the

mounting plate to the pivot

bracket

WARNING: The installer of these products must verify that

the mounting surface, ceiling or wall, will safely support the

combined weight of all attached equipment and hardware.

Video Mount Products will not be held liable for the improper

use or installation of its products.

Enjoy Your Mount!

10

3

2

11

12

16

11

4

5

8

15

4

13

3

1514

2

4

Este manual sirve para los siguientes modelos

1

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario