Vicon V923-N Manual de usuario

www.vicon-security.com

XX258-80-00

V923-N Network Camera

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the

operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed

to be used in life-critical situations and must not be used for this purpose.

Vicon Industries Inc.

Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300

Document Number: 8009-8258-80-00

Product specications subject to change without notice.

Issued: 913

Quick Guide

V923-N Quick Installation Guide

1. Description

The information in this manual provides quick installation and setup procedures for the V923-N

Camera . This unit should only be installed by a qualified technician using approved materials in

conformance with federal, state, and local codes. Read these instructions thoroughly before beginning

an installation. Always refer to Vicon’s website to assure you have the most up-to-date manual,

www.vicon-security.com.

The V923-N 3 Megapixel IP Camera is designed for demanding security installations. This network

camera delivers crisp clear images that satisfy any installation need. The V923-N camera is fully

compatible with all ViconNet® systems; its ONVIF certification provides an open-platform for

integration into other video management systems.

The camera is designed for easy installation. PoE eliminates the need for power cables, providing a

cost-effective method of installation; the camera also accepts 12 VDC and 24 VAC. The true day/night

camera includes a removable IR cut filter. A C/CS lens mount is provided, as is an autoiris connector.

The camera also supports two-way audio and alarm relays.

• Installation Steps

Follow these steps to install the network camera on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the network camera.

3. Set an IP address.

4. Set the password.

• Package Component

The system comes with the following components:

Camera unit Installation CD Installation Guide Accessory Kit Optional OSD Controller

Check your package to make sure that you received the complete system, including all components

shown above.

Note: The optional V920D-OSD OSD Controller can be purchased separately.

• Contents in the installation CD

1. The V923-N User’s Manual

2. The SmartManager User’s Manual

3. The SmartManager Installation software

V923-N Quick Installation Guide

2. Installation

For the network camera to operate, it is necessary to connect a network cable for data transmission

and power connection from supplied power adapter. Depending on operation methods, it is possible to

also connect an alarm cable.

2.1 Overview

NO Function

1 Back-focus adjusting locking

screw

2 Autoiris lens connector

2.2 Connection

NO Function Description

1 Power Adaptor

Terminal Main power, 2 pin terminal;

12 VDC 400 mA (4.5 W)/ 24 VAC 450 mA (5.0 W)

Power Indicator

(Green) Indicates power input

2 Status Indicator

(Red) Indicates camera status

Audio Input Audio input stereo jack

3 Audio Output Audio output stereo jack

4 Network Connector

(PoE) RJ-45 port compatible with 10/100Mbps having PoE

functionality

5 Video Output Connects the video output

6 Micro SD Card Slot Card slot for Micro SD. Open the protective cover with the

supplied tool to insert Micro SD card

3 Pin Terminal IO Connects alarm In/Out

7 2 Pin RS485 Terminal Connects pan-and-tilt device

8 Reset Button Executes the factory default

V923-N Quick Installation Guide

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC, while a direct cable is used for connection

to a hub.

• Connecting Alarms

AI (Alarm In):

You can use external devices to signal the network camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.

G (Ground):

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

AO (Alarm Out):

The network camera can activate external devices such as buzzers or lights. Connect the device

to the AO (Alarm Out) and G (Ground) connectors.

• Connecting the Power

Connect the power of 12 VDC or 24 VAC, 450 mA for the network camera. Connect the positive

(+) pole to the ‘+’ position and the negative (-) pole to the ‘-‘ position for the DC power.

• LED Indicators

LED Color Indication

Green Steady for connection to a 100 Mbit/s network. Flashes for

network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for

network activity.

Network

Unlit No network connection.

Status Red

Steady red for failed upgrade or booting.

Power Green

Steady green for normal operation or booting.

Flashes green during firmware upgrade.

Note: Steady green and red during booting. Flash green and red during factory default.

• Connecting Service Monitor Port

The Service Monitor output port is located rear the box camera and is used for easy OSD setup.

Set to NTSC

by default

V923-N Quick Installation Guide

• ID and IP assignment

To make changes in the OSD menu, the optional OSD controller (V920D-OSD) can be used to set

the camera title and IP address.

1. Connect the OSD Controller to the Service Monitor port of the network camera.

2. Connect Service Monitor and the Video Output port of the OSD Controller.

3. Press the SET button on the controller to access the Main Menu.

4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera

can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.

5. Select SAVE or CANCEL to exit the Main Menu.

The Video Output can also be used for easy zoom and focus control when adjusting the lens.

Video Output is restricted to 704x480 (576) resolution.

Note:

The optional V920D-OSD OSD Controller can be purchased separately.

2.3 Network Connection and IP assignment

The network camera is designed for use on an Ethernet network and requires an IP address for

access. Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. By the factory default, your camera is set to obtain the IP address automatically

via DHCP server. If your network does not have a DHCP server the network camera will use

192.168.1.100 as the default IP address.

If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to

search and allocate an IP address to your products, or reset the product to the factory default settings

and then perform the installation again.

1. Connect the network camera/device to the network and power up.

2. Start SmartManager utility (All Programs>SmartManager>SmartManager), the main window will

be displayed, after a short while any network devices connected to the network will be displayed

in the list.

V923-N Quick Installation Guide

3. Select the camera on the list and click right button of the mouse. The pop-up menu displays as

below.

4. Select Assign IP. The Assign IP window displays.

Note: For more information, refer to the Smart Manger User’s

Manual.

V923-N Quick Installation Guide

3. Operation

The network camera can be used with Windows operating system and browsers. The recommended

browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.

Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but

the functionality is the same or similar.

3.1 Access from a browser

1. Start a browser (i.e., Internet Explorer).

2. Enter the IP address or host name of the network camera (the camera name as it appears in the

ViconNet site list) in the Location/Address field of your browser.

3. A starting page displays. Click Live View or Setup to enter web page.

4. Click Live View for the network camera’s Live View page to appear in the browser.

3.2. Access from the internet

Once connected, the network camera is accessible on your local network (LAN). To access the

network camera from the Internet you must configure your broadband router to allow incoming data

traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to

automatically configure the router to allow access to the network camera. This is enabled from Setup

> System > Network > NAT.

For more information, refer to “3.5.5 System>Network>NAT” of User’s Manual.

V923-N Quick Installation Guide

3.3 Setting the admin password over a secure connection

ain access to the camera, the password for

he default administrator user must be set. This

is done in the “Admin Password” dialo

, which is

displayed when the network camera is accessed

or the setup at the first time. Enter your admin

name and password, set by the administrator.

Note: The default administrator username is

“ADMIN” and password is “1234”. If the

password is lost, the network camera must be

reset to the factory default settin

s. See “3.6

Resettin

to the Factory Default Settin

”

3.4 Live View Page

he live view pa

e comes in seven screen

modes: 1920x1080, 1280x1024, 1280x720,

704x480 (576), 640x480, 352x240 (288),

and 320x240. Select the most suitable

mode in accordance with your PC

specifications and monitoring purposes.

1) General controls

LiveViewPage Search&PlaybackPage SetupPage HelpPage

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. . For more information, see “3.5.1 Basic Configuration > Video &

Image” of User’s Manual.

Theresolutiondrop-downlistallowsyoutoselectthemostsuitable

video resolutions to be displayed on Live View page.

Theprotocoldrop-downlistallowstheselectionofthecombinationof

protocols and methods to use depending on your viewing requirements and on the properties of

the network.

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

videostream.

The Pause button pauses the video stream being played.

V923-N Quick Installation Guide

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The Digital Zoom button activates a zoom-in or zoom-out function for the video image on

the live screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screenview.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

Use the Speaker icon scale to control the volume of the speakers.

Use the Microphone icon scale to control the volume of the microphone.

3) Video and Audio Streams

The network camera provides several image and video stream formats. Your requirements and

the properties of your network will determine the type you use.

The Live View page in the network camera provides access to H.264, MPEG-4 and Motion JPEG

video streams and to the list of available video streams. Other applications and clients can also

access these video streams/images directly, without going via the Live View page.

3.5 Network Camera Setup

The Setup pages provide the configuration screens for the network camera, and is intended for

product Administrators, who have unrestricted access to all the Setup tools, and Operators, who have

access to the settings for Basic, Live View, Video & Image, Audio, Event, and System Configuration.

The network camera is configured by clicking Setup in the top right-hand corner of the Live View page.

Click on this page to access the online help that explains the setup tools

When accessing the network camera for the first time,

the “Admin Password” dialog appears. Enter your admin

name and password, set by the administrator.

Note: If the password is lost, the network camera must

be reset to the factory default settings.

See “3.6 Resetting to the Factory Default Settings”.

The default administrator username is “ADMIN” and

password is “1234”.

V923-N Quick Installation Guide

3.6 Resetting to the factory default settings

To reset the network camera to the original factory settings, go to the Setup>System> Maintenance

web page (described in “3.5.6 System > Maintenance in the complete User’s manual”) or use the

Reset Button on the network camera, as described below:

• Using the Reset Button

Follow the instructions below to reset the network camera to the factory default settings using

the Reset Button.

1. Switch off the network camera by disconnecting the power adapter.

2. Press and hold the Reset Button with a straightened paperclip while reconnecting the power.

3. Keep the Reset Button pressed until the Status indicator blinks.

4. Release the Reset Button.

5. When the Power Indicator changes to Green (this may take up to 40 seconds), the process

is complete and the network video camera has been reset.

6. The network camera resets to factory defaults and restarts after completing the factory reset.

CAUTION: When performing a Factory Reset, you will lose any settings you have saved.

3.7 More Information

For more information, refer to the network camera User’s manual, which is available on the CD

included in this package.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon V988D Manual de usuario

Vicon

Vicon V660B-312IR Instrucciones de funcionamiento

Vicon

Vicon I-Onyx MPD-955DN-O Manual de usuario

Vicon

Vicon I-ONYX VND-970IP Manual de usuario

Vicon

Vicon Roughneck V920D Series Instrucciones de instalación y funcionamiento

Vicon

Vicon VC367DSP Manual de usuario

Vicon

Vicon V980B Series Manual de usuario

Vicon

Vicon CRUISER S660V Instrucciones de funcionamiento

Vicon

Vicon V9360-6 Series Instrucciones de funcionamiento

Vicon

Vicon V662-D-2 Instrucciones de funcionamiento

Vicon

Vicon SURVEYOR4A Manual de usuario

Vicon

Vicon Roughneck Pro V2000B Series Manual de usuario

Vicon

Vicon V672-PTZ Manual de usuario

Vicon

Vicon V2008-W0950-LPR Manual de usuario

Vicon

Vicon Cruiser SN663V Instrucciones de funcionamiento

Vicon

Vicon V960D-W Series Manual de instrucciones

Vicon

Vicon XX235-01-01 Instrucciones de funcionamiento

Vicon

Vicon 360 Multi-Sensor Camera Series Manual de usuario

Vicon

Vicon VC-600 Series Manual de usuario

Vicon

Vicon V992D-IR Manual de usuario

Vicon

Vicon IX 4000 L Manual de usuario

Vicon

Vicon V8360W Series Manual de usuario

Vicon

Vicon VC2650-DSP Manual de usuario

Vicon

Vicon rouchneck V910V5 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario