Vicon V988D Manual de usuario



Vicon Industries Inc. does not warrant that the functions contained in this equipment will

meet your requirements or that the operation will be entirely error free or perform

precisely as described in the documentation. This system has not been designed to be

used in life-critical situations and must not be used for this purpose.

Document Number: 8009-8305-20-00 Product specifications subject to change without

Vicon Industries Inc.

Tel: 631-952-2288)

Fax: 631-951-2288

Toll Free: 800-645-9116

24-Hour Technical Support:

800-34-VICON

QUICK INSTALLATION GUIDE

XX305-20-00

V988D

Network 4K Dome Camera

Quick Guide

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX-

POSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY

METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER

OPENNINGS ON THE EQUIPMENT.

CAUTION

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is in-

tended to alert the user to the presence of dangerous voltage within the products

enclosure that may be of sufficient magnitude to constitute a risk of electric shock

to persons.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance (servicing) instructions

in the literature accompanying the product.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC INFORMATION: This equipment has been tested and found to

comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the

interference at his own expense.

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This Class A digital apparatus complies with Canadian ICES-003.

Cet

appareil

nume

rique

classe

est

conforme

norme

NMB-003

Canada.

WARNING

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

Readtheseinstructions.

Keeptheseinstructions.

Heedallwarnings.

Followallinstructions.

Donotusethisapparatusnearwater.

Cleanonlywithdrycloth.

Donotblockanyventilationopenings.Installinaccordancewiththemanufacturerinstructions.

Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,or other



apparatus

(includingamplifiers)thatproduceheat.

Donotdefeatthesafetypurposeofthepolarizedorgrounding‐typeplug.Apolarized



plughastwo

bladeswithonewiderthantheother.Agroundingtypeplughastwo blades



andathirdgroundingprong.

Thewidebladeorthethirdprongareprovidedforyoursafety.



Iftheprovidedplugdoesnotfitintoyour

outlet,consultanelectricianforreplacementofthe



obsoleteoutlet.

10.

Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplugs,convenience

receptacles,andthepointwheretheyexitfromtheapparatus.

11.

Onlyuseattachments/accessoriesspecifiedbythemanufacturer.

12.

Useonlywiththecart,stand,tripod,bracket,ortablespecified



bythe

manufacturer,orsoldwiththeapparatus.Whenacartis used.



Usecautionwhen

movingthecart/apparatuscombinationtoavoid injuryfromtip‐over.

13.

Unplugthisapparatusduringlightningstormsorwhenunused for



long

periodsoftime.

14.

Referallservicingtoqualifiedservicepersonnel.Servicingisrequired when the apparatus has been

damaged in any way,such as



power‐supply cordor plugisdamaged, liquid hasbeenspilled orobjects

havefallenintotheapparatus,theapparatushasbeenexposedtorainormoisture,



doesnotoperate

normally,orhasbeendropped.

15.

CAUTION−THESESERVICINGINSTRUCTIONSAREFORUSEBY QUALIFIED

SERVICEPERSONNELONLYTOREDUCETHERISKOFELECTRICSHOCKDO NOT



PERFORMANYSERVICING

OTHERTHANTHATCONTAINEDINTHEOPERATINGIN‐



STRUCTIONSUNLESSYOUQREQUALIFIEDTODOSO.

16.

Usesatisfyclause2.5ofIEC60950‐1/UL60950‐1orCertified/ListedClass2power



sourceonly.

17.

ITEistobeconnectedonlytoPoEnetworkswithoutroutingtotheoutsideplant.

Introduction

Vicon’s V988D-W311MIR HD IP Dome Camera is designed for performance in demanding security installations.

The camera provides 4K (8 MP) resolution with a 3.6-11 mm motorized varifocal lens. The camera offers IR

illuminators that provide superior images in low-light environments.

The V988D-W311MIR supports H.264/H.265 compression technology, drastically reducing file sizes and

conserving valuable network bandwidth. M-JPEG compression is also provided. The camera can provides quad

streaming for multi-camera displays.

1.1

Components

Thissystemcomeswiththefollowingcomponents;



Network

Camera 1

InstallationGuide 1

TemplateSheet 1

AccessoryKit 1

Note 1. Check your package to make sure that you received the complete system, including all components

listed above.

Note 2. Adapter for 12 VDC is not supplied.

Installation

For the operation of the network c amera, it is necessary to connect a network cable for

data

transmission, power connection from power adapter. Depending on operation

methods, it is possible to

connect an alarm cable additionally. For its fixation on different

locations, please consult with an installer.

2.1

Overview

•

Dimension

Dimensions Unit: mm

•

Extension Cable

No. Item Description

RJ-45

Ethernet, RJ-45 port compatible

with 10/100Mbps PoE Modular Jack

DC Jack Main Power, DC Jack, 12 VDC

AI: Alarm In

Alarm input and output, 3-pin terminal

G: GND

AO: Alarm Out

MIC: Audio In

Audio line input, 2-pin terminal

G: GND

SPK: Audio Out

Audio line output, 2-pin terminal

G: GND

•

Installing & Adjusting Camera

Carefully remove the contents from the box.

Loosen the four torx screws located on the front of the housing, leaving the screws intact in the

front portion.

Using the template sheet, make mounting holes and cable hole in the location (ceiling or wall) where

this dome camera is being installed.

Do not continue to turn the camera in same direction.

The cable connector can be detached.

2.2

Connection

•

Micro SD memory slot on the bottom board

Remove the cap at bottom of the camera to insert the SD memory card.

•

Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is

used for directly connection to PC, while a direct cable is used for

connection to a hub. You can also use a

router featuring PoE (Power over Ethernet) to

supply power to the camera.

•

Connecting Alarms

AI (Alarm In): You can use external devices to signal the network camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G

(Ground) connectors.

G (Ground): Connect the ground side of the alarm input and/or alarm output to the G

(Ground) connector.

AO (Alarm Out): The network camera can activate external devices such as buzzers

or lights. Connect the

device to the AO (Alarm Out) and G (Ground) connectors.

•

Connecting the Power

Connect the power of 12VDC for the network camera. Connect the positive (+) pole to the ‘+’ position and the

negative (-) pole to the ‘-’ position for the DC power.

–

Be careful not to reverse the polarity when connecting the power cable.

–

A router featuring PoE (Power over Ethernet) can also be used to supply power to

the camera.

–

For the power specifications, refer to the appendix, product specification intheUsermanual.

–

If PoE and 12 VDC are both applied, the camera will be supplied with power from

PoE.

•

Connecting Audio

Connect speaker to audio line output and external Mic to audio input line.

2.3

Resetting to the factory default settings

To reset the network camera to the original factory settings, go to the Setup

System

Maintenance web

page (described in “System

Maintenance” of User Manual) or use the

Reset button on the network

camera inside the bottom cap.

•

Using the Reset button:

Follow the instructions below to reset the network camera to the factory default settings using the Reset

button.

Switch off the network camera by disconnecting the power adapter.

Open the top cap.

Press and hold the Reset button with a straightened paperclip while reconnecting the

power.

Keep the Reset button pressed at least 5 (or more) seconds.

Release the Reset button.

The network camera resets to factory defaults and restarts after completing the factory

reset.

Close the bottom cap tightly to ensure waterproof.

CAUTION: When performing a Factory Reset, you will lose any settings that have been

saved. (Default

IP 192.168.30.220)

2.4

Network Connection & IP Assignment

ThenetworkcameraisdesignedforuseonanEthernetnetworkandrequiresanIPaddressforaccess.Most

networkstodayhaveaDHCPserverthatautomaticallyassignsIPaddressestoconnecteddevices.Bythe

factorydefault,yourcameraissettoobtaintheIPaddressautomaticallyviaDHCPserver.Ifyournetwork

doesnothaveaDHCPserverthenetworkcamerawilluse192.168.1.100asthedefaultIPaddress.

IfDHCPisenabledandtheproductcannotbeaccessed,runthe“SmartManager”utilitytosearchand

allocateanIPaddresstoyourproducts,orresettheproducttothefactorydefaultsettingsandthenperform

theinstallationagain.TheutilitycanbefoundontheViconwebsitewww.vicon‐security.com,onthe

SoftwareDownloadspageforViconcameras.

Connect the network camera/device to the network and power up.

Start SmartManager utility (Start

All programs

SmartManager

SmartManager).

); the main window

displays. After a short while any network devices connected to the network will be displayed in the list.

Select the camera on the list and click right button of the mouse. The pop-up menu below displays.

Select Assign IP Address. The Assign IP window displays. Enter the required IP address.

NOTE: For more information, refer to the SmartManager User Manual.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon V672V-1 Instrucciones de funcionamiento

Vicon

Vicon Roughneck V920D Series Instrucciones de instalación y funcionamiento

Vicon

Vicon V960D-N312 Manual de instrucciones

Vicon

Vicon V923-N Manual de usuario

Vicon

Vicon Cruiser SN663V Instrucciones de funcionamiento

Vicon

Vicon Surveyor MKII Series XX282-40-01 Guía rápida

Vicon

Vicon XX152-02-00 Manual de usuario

Vicon

Vicon V662-D Instrucciones de funcionamiento

Vicon

Vicon Roughneck V2100B Series Manual de usuario

Vicon

Vicon V840D Series Manual de usuario

Vicon

Vicon VC-620 Manual de usuario

Vicon

Vicon Cruiser SN663V-A Instrucciones de funcionamiento

Vicon

Vicon V600-C Series Manual de usuario

Vicon

Vicon Roughneck AI V2000 Series Manual de usuario

Vicon

Vicon Cruiser SN673V-B Manual de usuario

Vicon

Vicon CE202D-N Manual de usuario

Vicon

Vicon Surveyor 282-20-02 Series Manual de usuario

Vicon

Vicon Roughneck Pro V2000B Series Manual de usuario

Vicon

Vicon V662-D-2 Instrucciones de funcionamiento

Vicon

Vicon VC600 Manual de usuario

Vicon

Vicon S10-CH Mini Manual de usuario

Vicon

Vicon Surveyor MKII Series XX282-00-01 Manual de usuario

Vicon

Vicon Roughneck Pro V2000D Series Manual de usuario

Vicon

Vicon V940B Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario