Vicon SN680D-A-WNIR Manual de usuario
www.vicon-security.com
XX270-21-00
SN680D-A-WNIR Network
PTZ Dome
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc.
Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8270-21-00
Product specications subject to change without notice.
Issued: 415
Copyright © 2015 Vicon Industries Inc. All rights reserved.
Quick Guide
1 Introduction
The information in this manual provides quick installation and setup procedures for the
SN680D-A-WNIR Camera Dome. This unit should only be installed by a qualified techni-
cian using approved materials in conformance with federal, state, and local codes. Read
these instructions thoroughly before beginning an installation. Always refer to Vicon’s web-
site to assure you have the most up-todate manual, www.vicon-security.com.
Vicons SN680D-A-WNIR HD Network Dome Camera is designed for performance in the
most demanding security installations. The 1080P megapixel pan, tilt, zoom (PTZ) camera
series has an integrated 30x optical zoom lens (4.3 mm to 129 mm); integrated IR LEDs
provide illumination up to a range of 492 ft (150 m).
The SN680D-A-WNIR provides triple-streaming video and supports H.264 compression
technology, drastically reducing file sizes and conserving valuable network bandwidth. Users
can receive multiple streams simultaneously in different resolutions, frame rates and image
qualities for viewing on different platforms.
The PoE/12 VDC camera dome is designed for easy installation. The SN680D-A-WNIR can
be mounted on a wall or ceiling. Additional accessories allow the unit to be pendant mounted
on a wall mount or in-ceiling. The camera can be tilted to 10 degrees above the horizon.
1.1 Components
This system comes with the following components;
Dome Camera ························ 1
Installation Guide/CD ························ 1
RJ-45 Coupler ························ 1
2P screw type Connector ························ 1
5P screw type Connector ························ 1
12VDC Adaptor ························ 1 (Optional)
PoE Injector ························ 1 (Optional)
Install Adaptor ························ 1
2
1.2 Key Features
•Brilliant video quality
The network camera offers the highly efficient H.264 video compression, which drasti-
cally reduces bandwidth and storage requirements without compromising image qual-
ity. Motion JPEG is also supported for increased flexibility.
•Dual or Triple Streams
The network camera can deliver dual or triple video streams simultaneously at full
frame rate in all resolutions up to Full-HD (1920 x 1080p) using Motion H.264 and
JPEG. This means that several video streams can be configured with different com-
pression formats, resolutions and frame rates for different needs.
•Image setting adjustment
The network camera also enables users to adjust image settings such as contrast,
brightness and saturation to improve images before encoding takes place.
•Intelligent video capabilities
The network camera includes intelligent capabilities such as VCA(Video Content Anal-
ysis). The network camera’s external inputs and outputs can be connected to devices
such as sensors and relays, enabling the system to react to alarms and activate lights
or open/close doors.
•Improved Security
The network camera logs all user access, and lists currently connected users. Also, its
full frame rate video can be provided over HTTPS.
•Built-in Synchronized IR LED & Fixed IR LED
The camera is equipped with two built-in IR LEDs, a fixed one for wide view and a
zoom synchronized adjustable one for distant view.
•PoE (Power over Ethernet)
This network camera can be powered through PoE, which simplifies installation since
only one cable is needed for carrying power, as well as video controls.
•ONVIF Certificate
This is a global interface standard that makes it easier for end users, integrators, con-
sultants, and manufacturers to take advantage of the possibilities offered by network
video technology. ONVIF enables interoperability between different vendor products,
increased flexibility, reduced cost, and future-proof systems.
•Micro-SD Recording support
The network camera also supports a Micro-SD memory slot for local recording with
removable storage.
•Audio support
The network camera also supports two-way audio.
3
2 Installation
2.1 Installation
An optional mounting kit, either a wall mount (V660-HDB242) or ceiling mount (V660-HDB241),
is required to install the dome camera.
The wall or ceiling mount must be attached to a structural object such as hard wood, con-
crete that will support the weight of the mount and dome camera.
The use of a solid backboard is recommended when attaching to gypsum walls.
1. Remove the Protection pad and the tape from attached the dome camera.
2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic
bushing. (Ceiling using the supplied M6 tapping screw and bushing)
3. To seal tightly, wrap the thread of the pipe end with Teflon tape about 20 times for
sealing. Then use a silicone rubber sealant to seal the area where the wall (ceiling)
mount and the pipe meet.
4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange,
press it to the surface and line up the flange hole with drilled holes.
CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure water-
proofing.
CAUTION 2: When installing, a mounting bracket must be used.
4
2.1.1 Installation - Wall Mount
A wall mounting plate is supplied with the wall mount; this must be attached to a structural
object such as concrete that will support the weight of the mount and dome camera.
1. Select a suitable mounting location and verify there is sufficient cable to reach the
middle of the Wall Mount.
2. Mark and drill mounting holes in the mounting surface using the wall mount flange as
a template.
3. Secure the mounting plate to the wall using the hardware provided or appropriate for
the mounting surface.
4. Pull out cables required to connect to the dome camera from the wall or route cables
through a section of 0.75 in (19 mm) conduit pipe.
5. Remove the cable access plate from the underside of the wall mount bracket.
6. Attach the wall mount bracket using screws; route cables through the access plate
hole.
7. Attach the camera’s safety wire to the wall mount’s latch.
8. Route cables on the dome through the wall mount bracket. Fix the housing to the wall
mount bracket using the locking nut and tighten the housing set screw with the supplied
wrench.
9. After connecting cables, reattach the access plate.
5
2.1.2 Installation - Ceiling Mount
The ceiling mounting plate must be attached to a structural object such as concrete that will
support the weight of the mount and Dome Camera.
1Select a suitable mounting location
and verify there is sufficient cable to
connect with cables from the housing.
2Mark and drill mounting holes on
the surface using the ceiling mount
flange as a template.
3Secure the mounting plate to the
ceiling using the hardware provided
or appropriate for the mounting sur-
face.
4Pull out cables required to connect
to the dome camera from the ceiling.
5Attach the ceiling mount plate using
screws; route cables through the
locking nut.
6Route cables through the pipe.
Tighten the housing with the pipe
using the socket.
7Attach the housing’s safety wire to
the ceiling mount’s M6x35 tapping
screw.
8After connecting cables, fix the pipe
to the ceiling mount using the locking
nut..
9Tighten set screws of the socket and
locking nut with the supplied wrench.
This figure shows how to twist and
lock the housing with pipe.
6
2.2 Basic Configuration of Camera System
No. Connector Wire Color Description
1DC Jack BLACK 12VDC
2RJ-45 BLACK Ethernet, RJ-45 port compatible with
10/100Mbps (Option PoE++ functionality)
3RCA BLACK Audio Input
4RCA GRAY Audio Output
55-pin Cable
YELLOW Alarm Input 1
WHITE Alarm Input 2
VIOLET Alarm Input 3
BROWN Alarm Input 4
GRAY GND
62-pin Cable RED Alarm Out
BLACK GND
The camera must be installed by qualified service personnel in accordance with all local and
federal electrical and building codes.
7
2.3 Micro-SD Card Insertion
User can install and change Micro-SD card as shown in the following picture.
1. Open the Micro-SD card cover.
2. Install or change Micro-SD card.
3. Tightly close the Micro-SD card cover to ensure waterproof.
8
2.4 Connections
•Connecting the Network
Connect a standard RJ-45 cable to the network port of the camera. Generally a cross-
over cable is used for directly connection to PC, while a direct cable is used for con-
nection to a hub.
•Connecting Alarms
– A1,A2,A3,A4 (Alarm Input 1,2,3,4)
You can use external devices to signal the camera to react on events. Mechanical
or electrical switches can be wired to the A1,A2,A3,A4 (Alarm Input 1,2,3,4) and
G (Ground) connectors.
– G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground)
connector.
– AO (Alarm Output)
The camera can activate external devices such as buzzers or lights. Connect the
device to the AO (Alarm Output) and G (Ground) connectors.
•Connecting the Power
Connect power of 12VDC for the camera.
When using a 12VDC adapter, connect the positive (+) pole to the ’ + ’ position and the
negative (-) pole to the ’ - ’ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power
source only.
–Be careful not to reverse the polarity when you connect the power cable.
–You can use the PoE (Power over Ethernet) injector to supply power to the camera
with PoE option.
CAUTION: You must use PoE Injector provided by the manufacturer of this camera for
proper operation.
9
2.4.1 Network Connection & IP assignment
The network camera is designed for use on an Ethernet network and requires an IP ad-
dress for access. Most networks today have a DHCP server that automatically assigns IP
addresses to connected devices. By the factory default, your camera is set to obtain the IP
address automatically via DHCP server. If your network does not have a DHCP server the
network camera will use 192.168.1.100 as the default IP address.
If DHCP is enabled and the product cannot be accessed, run the SmartManager utility on
the CD to search and allocate an IP address, or reset the product to the factory default set-
tings and then perform the installation again.
1) Connect the network camera/device to the network and power up.
2) Start SmartManager utility (Start >All programs >SmartManager >SmartManager).
The main window will display, and after a short while any network devices connected to the
network will be displayed in the list.
3) Select the camera on the list and click right button of the mouse. You can see the pop-up
menu as below.
4) Select Assign IP Address. The Assign IP window will display. Enter the required IP ad-
dress.
NOTE: For more information, refer to the SmartManager Users Manual.
10
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vicon
Vicon
Vicon Roughneck AI V2000 Series Manual de usuario
Vicon
Vicon Roughneck V910V3 Series Manual de usuario
Vicon
Vicon Cruiser SN663V-A Instrucciones de funcionamiento
Vicon
Vicon V8360W Series Manual de usuario
Vicon
Vicon VC-700W Manual de usuario
Vicon
Vicon V960D-W Series Manual de usuario
Vicon
Vicon SurveyorVFTXX134-60-01 Manual de usuario
Vicon
Vicon V960D-W Series Manual de instrucciones
Vicon
Vicon SN680D-WNIR Manual de usuario
Vicon
Vicon roughneck V900 Manual de usuario
Vicon
Vicon CE202D-N Manual de usuario
Vicon
Vicon CE202D-WN Manual de usuario
Vicon
Vicon Surveyor MKII Series XX282-00-01 Manual de usuario
Vicon
Vicon SVFT-MSH23C Manual de usuario
Vicon
Vicon Roughneck AI V2000D Series Manual de usuario
Vicon
Vicon IX 2000 L Manual de usuario
Vicon
Vicon I-Onyx MPD-955DN-O Manual de usuario
Vicon
Vicon V662-D-1 Instrucciones de funcionamiento
Vicon
Vicon V1020-WIR-180-1 Manual de usuario
Vicon
Vicon V662V-2 Series Instrucciones de funcionamiento
