Vicon CE202D-N Manual de usuario

www.vicon-security.com

XX269-40-00

CE202D-N Network

Camera Dome

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the

operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed

to be used in life-critical situations and must not be used for this purpose.

Vicon Industries Inc.

Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300

Document Number: 8009-8269-40-00

Product specications subject to change without notice.

Issued: 314

Quick Guide

CE202D-N Series Quick Installation Guide

1. Description

The information in this manual provides quick installation and setup procedures for the CE202D-N

Series of Camera Domes. These units should only be installed by a qualified technician using approved

materials in conformance with federal, state, and local codes. Read these instructions thoroughly

before beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-

date manual, www.vicon-security.com.

The CE202D-N HD IP Camera Dome is designed for indoor security installations. This cost-effective

fixed network camera includes an integral 3.7 mm megapixel fixed lens; the 1080p resolution delivers

crisp clear images. The CE202D-N cameras are fully compatible with all ViconNet® systems; its ONVIF

certification provides an open-platform for integration into other video management systems.

The network camera provides triple-streaming video and supports H.264 compression technology.

MPEG-4 and Motion JPEG (M-JPEG) compressions are also provided, as are privacy masking and

motion detection. Installation is made easy and cost-effective with Power-over-Ethernet (PoE); the

camera also accepts 12 VDC.

• Installation Steps

Follow these steps to install the network camera on your local network (LAN):

1. Check the package contents against the list that follows.

2. Connect the network camera.

3. Set an IP address.

4. Set the password.

• Package Component

The system comes with the following components:

Camera Unit Installation CD Installation Guide Accessory Kit Template sheet

Alarm Cable Optional OSD Controller

Check your package to make sure that you received the complete system, including all components

shown above.

Note: Adapter for 12 VDC is not supplied and the optionalV920D-OSD OSD Controller can be

purchased separately.

• Contents in the installation CD

1. The CE202D-N User’s Manual

2. The SmartManager User’s Manual

3. The SmartManager Installation software

CE202D-N Series Quick Installation Guide

2. Installation

2.1 Camera Installation

Carefully remove the contents from the box, and verity that nothing was damaged in shipment.

1) Using the template sheet provided, make screw holes for camera on the ceiling.

2) Disassemble the camera by turning the camera cover counter-clockwise so it can be removed.

3) Secure the dome camera to the ceiling using the anchors (2x) and screws (2x) provided in the

accessory kit.

4) Reassemble the camera cover to dome camera by turning the camera cover clockwise until it locks

in place

Lock clockwise

Camera Dimension

See the diagrams below for the exact dimension. (Dimensions Unit: mm)

CE202D-N Series Quick Installation Guide

2.2 Connection

Connection Description

NO Name Description

1 Alarm Cable Yellow : Alarm input, Black : GND, Blue : Alarm output

2 Power Cable Cable for Power source (DC 12V)

3 Ethernet Cable Cable for Ethernet (POE)

NO Name Description

1 Factory Default Button Button for the factory default setting

2 Micro-SD Slot Micro-SD memory slot

3 Service Monitor Port Service Monitor (set to NTSC by default ; change video format from

Source menu); V920D-OSD Controller (option) Communication Port,

Mono Jack

CE202D-N Series Quick Installation Guide

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC, while a direct cable is used for connection

to a hub.

Micro SD memory slot

Insert the SD memory card (customer supplied).

• Connecting the Power

onnect a 12 VDC power adaptor (customer supplied) to the camera.

• Connecting Service Monitor Port

The Service Monitor output port is located on the board of the dome camera and is used for easy

OSD setup.

▶ID & IP assignment

To make changes in the OSD menu, the optional OSD controller can be used to set Camera Title

and IP Address.

1. Connect the OSD Controller to the Service Monitor port of the network camera.

2. Connect Service Monitor and the Video Output port of the OSD Controller.

3. Press the SET button on the controller to access the Main Menu.

4. Change camera ID and IP address as needed. Additionally, the Name (or title) of the camera

can be changed. Use the ↑↓←→ buttons on the controller to change the parameters.

5. Select SAVE or CANCEL to exit the Main Menu.

The Video Output can also be used for easy zoom and focus control when adjusting the lens.

Video Output is restricted to 704x480 (576) resolution.

Note:

The optional V920D-OSD OSD Controller can be purchased separately.

CE202D-N Series Quick Installation Guide

2.3 Network Connection and IP assignment

The network camera is designed for use on an Ethernet network and requires an IP address for

access. Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. By the factory default, your camera is set to obtain the IP address automatically

via DHCP server. If your network does not have a DHCP server the network camera will use

192.168.1.100 as the default IP address.

If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to

search and allocate an IP address to your products, or reset the product to the factory default settings

and then perform the installation again.

1. Connect the network camera to the network and power up.

2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager); the main

window will be displayed, after a short while any network devices connected to the network will

be displayed in the list.

3. Select the camera on the list and click right button of the mouse. Y The pop-up menu below

displays.

4. Select Assign IP. The Assign IP window displays. Enter the required IP address.

Note: For more information, refer to the Smart Manger

User’sManual.

CE202D-N Series Quick Installation Guide

3. Operation

The network camera can be used with Windows® operating system and browsers. The recommended

browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows.

Note: To view streaming video in Microsoft® Internet Explorer, set your browser to allow ActiveX

controls.

Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but

the functionality is the same or similar.

3.1 Access from a browser

1. Start a browser (i.e., Internet Explorer).

2. Enter the IP address or host name of the Network Camera in the Location/Address field of your

browser.

3. A starting page displays. Click Live View, Playback or Setup to select corresponding web page.

4. Click Live View for the network camera’s Live View page to appear in the browser.

CE202D-N Series Quick Installation Guide

3.2. Access from the internet

Once connected, the network camera is accessible on your local network (LAN). To access the

network camera from the Internet you must configure your broadband router to allow incoming data

traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to

automatically configure the router to allow access to the network camera. This is enabled from Setup

> System > Network > NAT.

For more information, please see “3.5.5 System>Network>NAT” of User’s Manual.

3.3 Setting the admin password over a secure connection

ain access to the product, the password for

he default administrator user must be set. This

is done in the “Admin Password” dialo

, which is

displayed when the network camera is accessed

or the setup at the first time. Enter your admin

name and password, set by the administrator.

Note: The default administrator username is

“

ADMIN” and password is “1234”. If the

password is lost, the network camera must be

reset to the factory default settin

s. See section

“

3.5 Resettin

to the Factory Default Settings” for

more details.

To prevent network eavesdropping when setting the admin password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate (see note below).

To set the password via a standard HTTP connection, enter it directly in the first dialog shown below.

To set the password via an encrypted HTTPS connection, see “3.5.5 System >Security>HTTPS” of

User’s Manual.

Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between

web browsers and servers. The HTTPS certificate controls the encrypted exchange of information.

3.4 Live View Page

he live view pa

e comes in several screen

modes, for example 1920x1080,

1280x1024, 1280x720, 800x600, 704x480

(576), 640x480, 352x240 (288) and

320x240. Select the most suitable mode in

accordance with your PC specifications and

monitorin

purposes.

CE202D-N Series Quick Installation Guide

1) General controls

LiveViewPage Search&PlaybackPage SetupPage HelpPage

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. For more information, see section “3.5.1 Basic Configuration >

Video & Image” of this user’s manual.

Theresolutiondrop-downlistallowstheselectionofthemostsuitablevideo

resolutions to be displayed on Live View page.

Theprotocoldrop-downlistallowstheselectionofthecombinationofprotocols

and methods to use depending on your viewing requirements and on the properties of the

network.

2) Control

toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

video stream.

The Pause button temporarily stops (pauses) the video stream being played.

The Snapshot button takes a picture (snapshot) of the current image. The location where

the image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

3) Video

Streams

The network camera provides several images and video stream formats. Your requirements and

the properties of your network will determine the type you use.

The Live View page in network camera provides access to H.264, MPEG-4 and Motion JPEG video

streams and to the list of available video streams. Other applications and clients can also access

these video streams/images directly, without going via the Live View page.

Otros manuales para CE202D-N

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon VC-700W Manual de usuario

Vicon

Vicon Roughneck V2000D-PTZ Manual de usuario

Vicon

Vicon CE202D-N Manual de usuario

Vicon

Vicon V8360W Series Manual de usuario

Vicon

Vicon V1020-WIR-180 Manual de usuario

Vicon

Vicon I-ONYX VND-970IP Manual de usuario

Vicon

Vicon Roughneck V2100B Series Manual de usuario

Vicon

Vicon Roughneck V894CSHR-VF-C Manual de usuario

Vicon

Vicon VC367DSP Manual de usuario

Vicon

Vicon V923-N Manual de usuario

Vicon

Vicon SN680D-WNIR Manual de usuario

Vicon

Vicon Surveyor 4 Manual de usuario

Vicon

Vicon VC-600 Series Manual de usuario

Vicon

Vicon Surveyor MKII Manual del propietario

Vicon

Vicon V660B-312IR Instrucciones de funcionamiento

Vicon

Vicon Cruiser SN663V-B-EX Instrucciones de funcionamiento

Vicon

Vicon V922B-W551MIR-A1 Manual de usuario

Vicon

Vicon V700W Series Manual de usuario

Vicon

Vicon IX4000AL Manual de usuario

Vicon

Vicon V960-N Series Manual de instrucciones

Vicon

Vicon S2000-MSH-HHB Surveyor 2000 Manual de usuario

Vicon

Vicon Roughneck Pro V2000 Series Manual de usuario

Vicon

Vicon SurveyorVF SVFT-M Manual de usuario

Vicon

Vicon V672D Instrucciones de funcionamiento

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario