Triplett TMP230 Manual de usuario

User Manual

TMP230

Deep-Frying Oil Tester/Oil Quality Meter

www.calcert.com sales@calcert.com1.888.610.7664 0

Introduction

Congratulations on your purchase of the Triplett TMP230 Deep-Frying Oil

Tester. This instrument checks temperature and TPM (Total Polar Materials)

in industrial and domestic fryers to know exactly when the oil has to be

replaced.

Description

METER DESCRIPTION

www.calcert.com sales@calcert.com1.888.610.7664 0

Safety

Please read this manual carefully and completely before you use the device

for the first time. Damage or injuries caused by non-observance of the manual

are excluded from our liability and not covered by our warranty.

The device must only be used as described in this instruction

manual. If used otherwise, this can cause dangerous situations for

the user and damage to the meter.

The instrument may only be used if the environmental conditions

(temperature, relative humidity) are within the ranges stated in the

technical specifications. Do not expose the device to extreme

temperatures, direct sunlight, extreme humidity or moisture. The

device is intended for indoor use.

Before the measurement, the device should have stabilized at

ambient temperature, which is important when moving from cold to

warm rooms and vice versa.

Do not expose the device to shocks or strong vibrations.

The case should only be opened by qualified personnel.

Before making a measurement, make sure the device is entirely

closed.

Never use the instrument when your hands are wet.

You must not make any technical changes to the device.

The appliance should be cleaned with a damp cloth after each

use. Use only pH-neutral cleaner, no abrasives or solvents.

When the frying oil tester is not used for a longer period of time,

remove the batteries.

Do not store the meter together with any chemicals.

Before each use, inspect the case for visible damage. If any

damage is visible, do not use the device.

Wear your personal protective equipment during each

measurement to avoid injury. This also applies to other people near

the measuring location as oil splashes can cause serious injury to

human skin and eyes.

To avoid burns, never touch the sensor or the metal shaft directly

after the measurement as these parts can become very hot when

they are immersed into hot oil.

Remove the oil quality meter from the oil when you leave the

place.

www.calcert.com sales@calcert.com1.888.610.7664 0

Do not use the instrument in explosive atmospheres. Also avoid

proximity to explosive, easily flammable or chemical substances

when the sensor is hot.

Only use the device in systems that are electrically tested on a

regular basis. Never connect the conductive metal parts of the meter

with a source of voltage. Inspect the system visually before each

measurement. If there are any signs of damage, do not carry out

any measurements until the problem has been resolved.

The measurement range as stated in the specifications must not

be exceeded under any circumstances.

Non-observance of the safety notes can cause damage to the

device and injuries to the user.

Triplett does not assume liability for printing errors or any other

mistakes in this manual.

Operation

Measurement

1. Press and release the on / off key to switch on the device.

2. The temperature display will show Lo

3. The PC display will show - - -

4. Insert the sensor into the hot oil so that the oil level is between the

minimum and maximum lines on the metal shaft.

5. If you want to freeze the measured value in the display, press the HOLD

key.

6. Press the HOLD again to deactivate the HOLD function.

7. When the temperature indication flashes and shows "HI", the oil/fat is too

hot and exceeds the upper end of the measurement range of 200 °C.

8. When the temperature indication flashes and shows "Lo", the oil/fat is

too cold and is below the lower end of the measurement range of 30

°C.

9. When the PC indication flashes and shows "Lo," the oil/fat used is not

suitable to be tested with the TMP230.

www.calcert.com sales@calcert.com1.888.610.7664 0

Important notes to achieve the most accurate results

During the measurement, there should not be any fried food in

the oil/fat. After taking out the fried items, wait at least 5

minutes before making a measurement.

If you would like to measure in an induction cooker, switch it off as

its electromagnetic field can falsify the result.

Stir the oil/fat briefly with the device to ensure an even

temperature.

Avoid direct contact with metal objects such as cooking pots

or frying baskets as this can influence the measurement

result. Minimum distance: 1 cm.

Replace the oil/fat when a PC value of 24 % is reached.

Different countries have different threshold values to stick to. It

is recommended to replace the oil/grease before reaching the

threshold value.

Settings / configuration mode

Activate the configuration mode by pressing the HOLD key and the arrow left

key at the same time. Now you can navigate through the submenus, make

the desired settings and confirm these by pressing the HOLD key. The next

menu will open automatically.

Set temperature unit

Switch on the device and press the HOLD key and the arrow left key

simultaneously for approx.

3 seconds. °C or °F will appear in the display.

1. Use the arrow keys to set the temperature unit (°C/°F).

2. Confirm the selected temperature unit by pressing the HOLD key to

confirm.

Switch on / off audible alarm (ALA)

1. Use the arrow keys to switch on / off the audible alarm (ALA).

2. Press the HOLD key to confirm.

Switch on / off Auto Power Off function (OFF)

1. Press the arrow keys to switch on / off the Auto Power Off function.

2. Confirm your selection with the HOLD key.

www.calcert.com sales@calcert.com1.888.610.7664 0

Switch on / off alarm LED

1. Use the arrow keys to turn on / off the LEDs.

2. Press the HOLD key to confirm.

Switch on / off calibration mode (CAL)

1. Press the arrow keys to switch on / off calibration mode.

2. Press the HOLD key to confirm.

Reset device to factory settings (RST)

1. Use the arrow keys to reset the device to its factory settings (on).

2. Press the HOLD key to save and exit.

Switch the background lighting (BL) on or off

1. Press the arrow keys to turn on / off the backlight.

2. Press the HOLD key to save and exit.

To leave configuration mode, press the on / off key.

Advanced alarm settings

Switch on PC alarm (High)

1. Switch on the device and hold down the arrow left key for approx. 3

seconds until the LEDs turn red.

2. Use the arrow keys to set the alarm value.

3. Save the setting by pressing the HOLD key or press the on / off key to

return to measurement mode without saving.

Switch on PC alarm (Low)

1. Switch on the device and hold down the arrow right key for approx. 3

seconds until the LEDs turn green.

2. Use the arrow keys to set the alarm value.

3. Save the setting by pressing the HOLD key or press the on / off key to

return to measurement mode without saving.

Calibration

1. Use a reference oil with a known PC value for calibration. Heat the oil to

50 °C.

2. Enter calibration mode as described above. CAL will be displayed.

Immerse the sensor into the calibration oil. Make sure the oil is between

the Min/Max lines on the sensor shaft.

3. When the reading has stabilised, press the arrow keys to adjust the

reading in increments of 0.5 %.

www.calcert.com sales@calcert.com1.888.610.7664 0

4. When the displayed value matches the reference value, press the HOLD key to

save the value.

You can reset your calibration to factory settings by opening the menu

item factory settings (RST) via the configuration mode as described

under Settings and then pressing the arrow right key and the HOLD key.

Switch on / off calibration mode (CAL)

1. Press the arrow keys to switch on / off calibration mode.

2. Press the HOLD key to confirm.

Specifications

Technical specifications

Temperature

Temperature measurement range

104 to 392

°F (

+200 °C

)

Temperature accuracy

3.0°F (

±1.5 °C

)

Temperature resolution

0.1°F/°C; 0.5%

TPM (Total Polar Materials)

TPM

measurement range

0.5 ... 40 % polar fractions

TPM

accuracy

TPM

resolution

0.1 %

General

Measurable materials

Olive oil, Palm oil, Rapese

ed oil,

Peanut oil, Soybean

oil, Sesame oil, further

Vegetable oils or Animal fats

Power supply

2 x 1.5 V AAA battery

Battery life

approx. 500 measurements /

25 h continuous

operation

Temperature sensor

PTC sensor

Oil sensor

apacitive sensor

Operating temperat

ure

32 to 122°F (

0 to

50 °C

)

Storage temperature

4 to 158°F (

20 ... +70 °C

)

Display LCD, 3 digits

Dimensions (W x D x H)

Weight

8.8oz (248g)

Case material

ABS

Protection class

IP65

www.calcert.com sales@calcert.com1.888.610.7664 0

* As different fats and oils have different characteristics, the measured PC

values can deviate by a certain percentage, depending on the type of oil/fat.

Interpretation of the measured values

Oil is new and good to use (LED flashes in green)

0 ... 18.5

Oil quality classified as critical (LED flashes in blue

19 ... 24 %

It is recommended to renew the oil partly or completely.

The oil in the fryer should no longer be used.

>24 %

The set threshold value (default setting: 24 %) has been

exceeded and the

LED flashes in red.

The oil must be exchanged completely.

Disposal

For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament applies.

Due to the contained pollutants, batteries must not be disposed of as household waste. They must be

given to collection points designed for that purpose.

In order to comply with the EU directive 2012/19/EU we take our devices back. We either re-use

them or give them to a recycling company which disposes of the devices in line with law.

For countries outside the EU, batteries and devices should be disposed of in accordance with

your local waste regulations

Warranty

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products

sold by it will be free from defects in workmanship and material for a period of (1) one

year from the date of purchase. This warranty does not apply to any of our products

which have been repaired or altered by unauthorized persons in any way or purchased

from unauthorized distributors so as, in our sole judgment, to injure their stability or

reliability, or which have been subject to misuse, abuse, misapplication, negligence,

accident or which have had the serial numbers altered, defaced, or removed.

Accessories, including batteries are not covered by this warranty

www.calcert.com sales@calcert.com1.888.610.7664 0

Tabla de contenidos

Otros manuales de Instrumento de medición de Triplett

Triplett

Triplett TA200 Manual de usuario

Triplett

Triplett EM400 Manual de usuario

Triplett

Triplett hotwire fox Manual de usuario

Triplett

Triplett The Hound 2 Manual de usuario

Triplett

Triplett MS475 Manual de usuario

Triplett

Triplett 9200-A Manual de usuario

Triplett

Triplett CTX690 Manual de usuario

Triplett

Triplett RHT01 Manual de usuario

Triplett

Triplett LT68 Manual de usuario

Triplett

Triplett EM300 Manual de usuario

Triplett

Triplett 630 Manual de usuario

Triplett

Triplett CM450-NIST Manual de usuario

Triplett

Triplett RHT22 Manual de usuario

Triplett

Triplett 60-A Manual de usuario

Triplett

Triplett RHT02 Manual de usuario

Triplett

Triplett MS120 Manual de usuario

Triplett

Triplett 2030-C Manual de usuario

Triplett

Triplett GSM350 Manual de usuario

Triplett

Triplett CM1050 Manual de usuario

Triplett

Triplett GSM450 Manual de usuario

Triplett

Triplett PR400 Manual de usuario

Triplett

Triplett PH180 Manual de usuario

Triplett

Triplett HS10 Manual de usuario

Triplett

Triplett LT80 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario