Endress+Hauser Proline Promag 50 Especificaciones técnicas

KA00026D/06/EN/14.11

71154524

Brief Operating Instructions

Proline Promag 50

Electromagnetic Flow Measuring System

These Brief Operating Instructions are not intended to replace the

Operating Instructions provided in the scope of supply.

Detailed information is provided in the Operating Instructions and

the additional documentation on the CD-ROM supplied.

The complete device documentation consists of:

• These Brief Operating Instructions

• Depending on the device version:

– Operating Instructions and the Description of Device Functions

– Approvals and safety certificates

– Special safety instructions in accordance with the approvals for

the device (e.g. explosion protection, pressure equipment

directive etc.)

– Additional device-specific information

Q-Pulse Id

Active 30/09/2014

Page 1 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 1 of 52

Proline Promag 50

2Endress+Hauser

Table of contents

1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.2 Installation, commissioning and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4 Safety conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Transporting to the measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Installing the Promag L sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4 Installing the W sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.5 Installing the Promag P sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.6 Installing the Promag H sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

2.7 Installing the transmitter housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2.8 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.1 Connecting the various housing types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.2 Connecting the remote version connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.3 Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4 Hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4.1 Device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4.2 Terminating resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.1 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5.3 Navigating within the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

5.4 Calling the Commissioning Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

5.5 Software settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

5.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Q-Pulse Id

Active 30/09/2014

Page 2 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 2 of 52

Proline Promag 50 Safety instructions

Endress+Hauser 3

1 Safety instructions

1.1 Designated use

• The measuring device is to be used only for measuring the flow of conductive liquids in closed

pipes. A minimum conductivity of 20 μS/cm is required for measuring demineralized water.

Most liquids can be measured as of a minimum conductivity of 5 μS/cm.

• Any use other than that described here compromises the safety of persons and the entire

measuring system and is, therefore, not permitted.

• The manufacturer is not liable for damage caused by improper or non-designated use.

1.2 Installation, commissioning and operation

• The measuring device must only be installed, connected, commissioned and maintained by

qualified and authorized specialists (e.g. electrical technicians) in full compliance with the

instructions in these Brief Operating Instructions, the applicable norms, legal regulations and

certificates (depending on the application).

• The specialists must have read and understood these Brief Operating Instructions and must

follow the instructions they contain. If you are unclear on anything in these Brief Operating

Instructions, you must read the Operating Instructions (on the CD-ROM). The Operating

Instructions provide detailed information on the measuring device.

• The measuring device should only installed in a de-energized state free from outside loads or

strain.

• The measuring device may only be modified if such work is expressly permitted in the

Operating Instructions (on the CD-ROM).

• Repairs may only be performed if a genuine spare parts kit is available and this repair work is

expressly permitted.

• If performing welding work on the piping, the welding unit may not be grounded by means

of the measuring device.

1.3 Operational safety

• The measuring device is designed to meet state-of-the-art safety requirements, has been

tested, and left the factory in a condition in which it is safe to operate. Relevant regulations

and European standards have been observed.

• The manufacturer reserves the right to modify technical data without prior notice. Your

Endress+Hauser distributor will supply you with current information and updates to these

Operating Instructions.

• The information on the warning notices, nameplates and connection diagrams affixed to the

device must be observed. These contain important data on the permitted operating conditions,

the range of application of the device and information on the materials used.

• If the device is not used at atmospheric temperatures, compliance with the relevant marginal

conditions as specified in the device documentation supplied (on CD-ROM) is mandatory.

• The device must be wired as specified in the wiring and connection diagrams. Interconnection

must be permitted.

Q-Pulse Id

Active 30/09/2014

Page 3 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 3 of 52

Safety instructions Proline Promag 50

4Endress+Hauser

• All parts of the device must be included in the potential equalization of the system.

• Cables, certified cable glands and certified dummy plugs must be suitable to withstand the

prevailing operating conditions, such as the temperature range of the process. Housing

apertures that are not used must be sealed with dummy plugs.

• The device should only be used for fluids to which all the wetted parts of the device are

sufficiently resistant. With regard to special fluids, including fluids used for cleaning,

Endress+Hauser will be happy to assist in clarifying the corrosion-resistant properties of

wetted materials.

However, minor changes in temperature, concentration or in the degree of contamination in

the process may result in variations in corrosion resistance.

For this reason, Endress+Hauser does not accept any responsibility with regard to the

corrosion resistance of wetted materials in a specific application. The user is responsible for

the choice of suitable wetted materials in the process.

• When hot fluid passes through the measuring tube, the surface temperature of the housing

increases. In the case of the sensor, in particular, users should expect temperatures that can

be close to the fluid temperature. If the temperature of the fluid is high, implement sufficient

measures to prevent burning or scalding.

• Hazardous areas

Measuring devices for use in hazardous areas are labeled accordingly on the nameplate.

Relevant national regulations must be observed when operating the device in hazardous areas.

The Ex documentation on the CD-ROM is an integral part of the entire device documentation.

The installation regulations, connection data and safety instructions provided in the Ex

documentation must be observed. The symbol and name on the front page provides

information on the approval and certification (e.g. 0Europe, 2USA,

1Canada). The

nameplate also bears the documentation number of this Ex documentation (XA***D/../..).

• For measuring systems used in SIL 2 applications, the separate manual on functional safety

(on the CD-ROM) must be observed.

• Hygienic applications

Measuring devices for hygienic applications have their own special labeling. Relevant national

regulations must be observed when using these devices.

• Pressure instruments

Measuring devices for use in systems that need to be monitored are labeled accordingly on the

nameplate. Relevant national regulations must be observed when using these devices. The

documentation on the CD-ROM for pressure instruments in systems that need to be

monitored is an integral part of the entire device documentation. The installation regulations,

connection data and safety instructions provided in the Ex documentation must be observed.

• Endress+Hauser will be happy to assist in clarifying any questions on approvals, their

application and implementation.

Q-Pulse Id

Active 30/09/2014

Page 4 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 4 of 52

Proline Promag 50 Safety instructions

Endress+Hauser 5

1.4 Safety conventions

#Warning!

"Warning" indicates an action or procedure which, if not performed correctly, can result in injury

or a safety hazard. Comply strictly with the instructions and proceed with care.

"Caution!

"Caution" indicates an action or procedure which, if not performed correctly, can result in

incorrect operation or destruction of the device. Comply strictly with the instructions.

!Note!

"Note" indicates an action or procedure which, if not performed correctly, can have an indirect

effect on operation or trigger an unexpected response on the part of the device.

Q-Pulse Id

Active 30/09/2014

Page 5 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 5 of 52

Installation Proline Promag 50

6Endress+Hauser

2 Installation

2.1 Transporting to the measuring point

• Transport the measuring device to the measuring point in the original packaging.

• Do not remove the covers or caps until immediately before installation.

2.1.1 Transporting flanged devices DN ≤300 (≤ 12")

2.1.2 Transporting flanged devices DN > 300 (> 12")

Use only the metal eyes provided on the flanges to transport, lift or position the sensor in the

piping.

"Caution!

Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing!

This would buckle the casing and damage the internal magnetic coils.

A0008153

A0007408

To transport the unit, use slings slung around the process

connections or use lugs (if available).

#Warning!

Risk of injury! The device can slip.

The center of gravity of the measuring device may be

higher than the holding points of the slings.

Always ensure that the device cannot slip or turn around

its axis.

A0007409

Do not lift measuring devices by the transmitter housing

or the connection housing in the case of the remote

version. Do not use chains as they could damage the

housing.

Q-Pulse Id

Active 30/09/2014

Page 6 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 6 of 52

Proline Promag 50 Installation

Endress+Hauser 7

2.2 Installation conditions

2.2.1 Dimensions

For the dimensions of the measuring device, see the associated Technical Information on the

CD-ROM.

2.2.2 Mounting location

The accumulation of air or formation of gas bubbles in the measuring tube can result in an

increase in measuring errors.

For this reason avoid the following mounting locations in the pipe:

• At the highest point of a pipeline. Risk of air accumulating!

• Directly upstream from a free pipe outlet in a down pipe.

0008154

Installation of pumps

Do not install the sensor on the intake side of a pump. This precaution is to avoid low pressure

and the consequent risk of damage to the lining of the measuring tube. It might be necessary to

use pulse dampers in systems incorporating piston pumps, piston diaphragm pumps or peristaltic

pumps.

Information on the measuring system's pressure tightness and resistance to vibration and shock

can be found in the Operating Instructions of the CD-ROM.

0003203

h 2xDN³

Q-Pulse Id

Active 30/09/2014

Page 7 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 7 of 52

Installation Proline Promag 50

8Endress+Hauser

Partially filled pipes

Partially filled pipes with gradients necessitate a drain-type configuration.

The empty pipe detection (EPD) function offers additional protection by detecting empty or

partially filled pipes.

"Caution!

Risk of solids accumulating! Do not install the sensor at the lowest point in the drain. It is

advisable to install a cleaning valve.

Down pipes

Install a siphon or a vent valve downstream of the sensor in down pipes longer than 5 meters

(16 ft). This precaution is to avoid low pressure and the consequent risk of damage to the lining

of the measuring tube. This measure also prevents the system losing prime, which could cause

air pockets.

For information on the pressure tightness of the measuring tube lining, see the Operating

Instructions on the CD-ROM.

A0008155

Installation in a partially filled pipe

A0008157

Measures for installation in a down pipe (h > 5 m/16 ft)

1. Vent valve

2. Siphon

5xDN

2xDN

Q-Pulse Id

Active 30/09/2014

Page 8 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 8 of 52

Proline Promag 50 Installation

Endress+Hauser 9

2.2.3 Orientation

An optimum orientation helps avoid gas and air accumulations and buildup in the measuring

tube. The measuring device, nevertheless, supplies a range of functions and tools to measure

problematic fluids correctly:

• Electrode cleaning circuitry (ECC) to prevent electrically conductive deposits in the

measuring tube, e.g. for fluids causing buildup

• Empty pipe detection (EPD) for detecting partially filled measuring tubes, e.g. in the case of

degassing fluids or varying process pressures

• Exchangeable measuring electrodes for abrasive fluids (only Promag W)

Vertical orientation

Horizontal orientation

The measuring electrode plane should be horizontal. This prevents brief insulation of the two

electrodes by entrained air bubbles.

"Caution!

In the case of horizontal orientation, empty pipe detection only works correctly if the transmitter

housing is facing upwards. Otherwise there is no guarantee that empty pipe detection will

respond if the measuring tube is only partially filled or empty.

A0008158

This orientation is optimum for self-emptying piping

systems and when using empty pipe detection (EPD) or

open electrode detection (OED).

A0008159

1. EPD electrode for empty pipe detection

(not for Promag H, DN 2 to 15, 1/12" to ½").

2. Measuring electrodes for signal detection

3. Reference electrode for potential equalization

(not for Promag H)

Q-Pulse Id

Active 30/09/2014

Page 9 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 9 of 52

Installation Proline Promag 50

10 Endress+Hauser

Inlet and outlet runs

If possible, install the sensor upstream from fittings such as valves, T-pieces, elbows, etc.

2.2.4 Vibrations

Secure and fix both the piping and the sensor if vibrations are severe.

A0008160

The following inlet and outlet runs must be observed in

order to meet accuracy specifications:

•Inletrun:≥5 × DN

• Outlet run: ≥2 × DN

A0008161

Measures to prevent device vibration

(L > 10 m/33 ft)

"Caution!

It is advisable to install the sensor and transmitter

separately if vibration is excessively severe. For

information on the permitted shock and vibration

resistance, see the Operating Instructions on the

CD-ROM.

5xDN³³2xDN

Q-Pulse Id

Active 30/09/2014

Page 10 of 52

Vendor Manual - Electromagnetic Flowmeter - Endress and Hauser - Model Proline Promag 50 - Operating Instructions

Q-Pulse Id VM454

Active 30/09/2014

Page 10 of 52

Otros manuales para Proline Promag 50

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser FlowFit P CPA 240 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar S FMD76 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD72 Especificaciones técnicas

Endress+Hauser

Endress+Hauser LT1100 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot FMR50 Instrucciones de instalación

Endress+Hauser

Endress+Hauser FOUNDATION Fieldbus Micropilot FMR50 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquipoint T FTW31 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar PMC71B Especificaciones técnicas

Endress+Hauser

Endress+Hauser memo-graph RSG10 Manual de usuario

Endress+Hauser

Endress+Hauser FOUNDATION Proline 500 digital Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual de usuario

Endress+Hauser

Endress+Hauser FHG65 Manual de usuario

Endress+Hauser

Endress+Hauser Micropilot M FMR240 Instrucciones de funcionamiento e instalación

Endress+Hauser

Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass 83 Manual de usuario

Endress+Hauser

Endress+Hauser Turbimax CUE25 Manual de usuario

Endress+Hauser

Endress+Hauser Memosens CPS16D Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP56 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic FMU 860 Manual

Endress+Hauser

Endress+Hauser EngyCal RH33 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Micropilot FMR67B Manual

Endress+Hauser

Endress+Hauser Levelflex FMP51 Manual de usuario

Endress+Hauser

Endress+Hauser Deltapilot M FMB51 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Prosonic M FMU40 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario