Trikdis G10T Manual de usuario

GSM communicator G10T

(v.2.3X)

USER MANUAL

UAB “TRIKDIS”

Draugystės str. 17,

LT-51229 Kaunas

LITHUANIA

E-mail: info@trikdis.lt

Webpage: www.trikdis.lt

GSM communicator G10T v.2

Description

GSM communicator can connect to any intruder alarm panel via its landline communicator and transmit

messages to an alarm receiving centre (ARC) and/or to a mobile/WEB application. Messages are transmitted

using GPRS, SMS via GSM network.

Compatible with control panels which has PSTN telephone communicator.

Features

Connection

Compatible with most control panels

Connection to control panels via:

oTLC terminal connection

Communications

Communication modes:

oGPRS

oSMS

oDTMF tones

Primary and backup channels



If the GPRS connection with primary and backup

servers will be lost, information can be sent in

SMS messages;

Mobile/Web application using a cloud service.

Allowing user to remotely monitor and control

the alarm system



Domain can be set as an IP address of IP receiver



Event messages can be transmitted in Contact ID

codes



Event reporting via SMS messages to 4 different

users in user customized SMS messages



PING technology to detect communication

problems

Constant control of connection with ARC



Messages receivers: software IPcom; hardware

(HW) receivers RL10 and RM10 and GM5; almost

every telephone receiver

Configuration



Quick and easy configuration and firmware

update



Operating parameters and firmware version can

be updated remotely



Operating parameters are set with program

G10config

Inputs and outputs

1 Output controlled via:

oMobile/Web application

oSMS

oInternal events

2 Inputs, type: NC

GSM communicator G10T v.2

Content

Safety requirements ...................................................................................................................................................2

Liability restrictions..................................................................................................................................................... 2

Communicator G10T operating.................................................................................................................................3

Technical specification ..............................................................................................................................................3

Package contents....................................................................................................................................................... 3

Outside view..............................................................................................................................................................3

Description of terminal block ..................................................................................................................................3

Light indication........................................................................................................................................................ 4

Communicator installation steps...............................................................................................................................4

Recommendations for programming of security control panel ................................................................................ 4

Wiring diagram.......................................................................................................................................................... 4

Setting of operating parameters ...............................................................................................................................5

Protegus service ........................................................................................................................................................9

Updating communicator firmware version.................................................................................................................9

Setting of configuration remotely ........................................................................................................................... 10

Firmware version upgrading remotely ....................................................................................................................11

Remote PGM output switching ...............................................................................................................................11

Safety requirements

Please read this manual carefully before using the security module G10T.

Security communicator G10T should be installed and maintained by qualified personnel, having specific knowledge

regarding the functioning of GSM devices and safety requirements.

Communicator G10T should be mounted in places with restricted access and in safe distance from any sensitive electronic

equipment. The device is not resistant to mechanical effects, dampness and hazardous chemical environment.

Liability restrictions

When buying the Device, the Buyer agrees that the Device is a part of a security system of premises, which sends

messages about security system status. The Device, when installed, does not diminish the probability of burglary, fire,

intrusion or other breach of premises.

UAB “TRIKDIS” is not responsible for burglary, fire or any other breach of Buyer’s and/or User’s premises and is not liable

for any direct or indirect damages incurred thereof.

When buying the Device, the Buyer agrees that the Device supplied by UAB “TRIKDIS” fully meets his requirements for

intended use.

UAB “TRIKIDIS” provides no guarantees that the Device shall function as declared if the Device is installed and used not

according to its original purpose, user manual and relevant electronic and technical conditions.

UAB “TRIKDIS” is in no way associated with GSM/GPRS/Internet service providers (operators), thus UAB “TRIKDIS” is in

no way responsible for any defects in Device operation if they have occurred because of the loss of GSM/GPRS/Internet

connection, or because of other defects in the service provider network.

UAB “TRIKDIS” has no control and is not responsible for the prices and marketing of network services provided by the

GSM/GPRS/Internet service providers.

UAB „TRIKDIS” is not responsible if GSM/GPRS/Internet services are not provided to the Buyer and/or User of the Device

or were cancelled and any direct or indirect damages were incurred thereof.

UAB „TRIKDIS” is not responsible for any direct or indirect damages incurred by the Buyer and/or User of the Device due

to loss of electricity.

UAB „TRIKDIS” is not liable if Device firmware versions were not updated by the Buyer and/or the User on time.

User manual of the Device can contain technical inaccuracies, grammatical or typographical errors. UAB “TRIKDIS”

reserves the right to correct, update and/or change information in the installation manual.

GSM communicator G10T v.2

Communicator G10T operation description

The communicator G10T is connected to security control panel contacts for connecting a telephone landline. In case of an

event, the security control panel dials number 1234. Module G10T picks up the phone and receives control panel message.

After receiving the message, the module transmits it to ARC through GSM connection channel set as primary. If the module is

unable to transmit the message through the primary connection channel, the module can send it through GSM connection

channel set as backup. Messages are sent through GSM connection according to set IP addresses or telephone numbers.

If the module loses connection with both the primary and the backup IP addresses, the module can send information to ARC

with SMS messages.

If G10T loses communication with both primary and backup IP receiver then it will send Contact ID messages with encrypted

SMS to SMS receiver (modem) at ARC.

The module can send messages to specified recipients about the breakage/restoration of external circuits IN1 and IN2.

Messages can be sent with SMS messages to four mobile phones. SMS message can contain of user-friendly text which

describes security control panel event.

Module output OUT1 state will invert when GSM connection with server at ARC fails/restores or when the module receives

an SMS message containing of command to change its output state.

Module can periodically transmit signals PING for testing communication channel.

Note: if G10T will loose communication with any receiver at ARC, it will send communication trouble signal to alarm control

panel.

Technical specification

Parameter

Description

Power supply voltage

DC 10…16V

Used current

60–100 mA (stand-by),

Up to 250 mA (transmitting)

GSM modem M12

Dual-band 900 / 1800 MHz

Memory

Up to 60 messages

Inputs

2, NC type

Output

1 OC type, commutating up to 30 V voltage and current up to 1 A

Setting configuration

Through the USB port

Operating environment

From -30 °C to 70 °C, with relative air humidity 80% when +20 °C

Dimensions

65 x 79 x 25 mm

Package contents

Communicator G10T

1 pc.

Two-sided adhesive tape (10 cm)

1 pc.

Note: GSM antenna of desired type is collected by the additional request.

Outside view

Description of terminal block

Contact

Description

+12V power supply clamp

COM

Common clamp

TIP

For connecting to the TIP clamp of security control panel

RING

For connecting to the RING clamp of security control panel

IN1

1st input clamp (NC type)

IN2

2nd input clamp (NC type)

OUT1

PGM output clamp (OC type)

COM

Common clamp

MCI

Provided for future use

1. Terminal block

SIM card holder

3. USB socket

4. LED indicators

5. GSM antenna

GSM communicator G10T v.2

Light indication

LED

Operation

Description

Network presents status of

connection to GSM

network

Green ON

Module has been connected to GSM network

Yellow ON

Message is being sent

Green flashing

Connecting to GSM network

Yellow flashing

Number of yellow flashes represent GSM signal strength

Data presents data

exchange.

Green ON

Unsent messages present in module memory

Red ON

Unable messages to be sent

Green flashing

Messages are being received from the control panel

Red flashing rapidly

Module configuration is incorrect

Red flashing

SIM card error

Power presents power

supply status, functioning

of microcontroller and

programming status

Green flashing

Power supply is sufficient, microcontroller is functioning

Yellow flashing

Power supply is not sufficient (≤11,5 V) but microcontroller is

functioning

Green and yellow flashing in turn

Programming mode

Communicator installation steps

Program security control panel

Use Programming manual of particular security control panel to set operation parameters as following:

1. Enable the PSTN dialler of the panel.

2. Select DTMF mode.

3. Select Contact ID communication format.

4. Enter a telephone number for dialling (you can use any number not shorter than 2-digits).

5. Enter a 4-digit account number in the panel.

1. Set the operating parameters for the security control panel telephone

communicator according to recommendations in section

Recommendations for

programming of security control panel.

Configure communicator parameters before installation. For communicator

configuration please refer to chapter Setting Operating Parameters.

3. Insert Standard SIM card to the holder.

Note: Using your mobile phone, register SIM card in the GSM network and enable

mobile data communication service.

We recommend do not use prepaid SIM card.

Disable PIN code request!

4. Screw the GPS antenna on.

5. Fasten the communicator with adhesive tape.

6. Connect wires as shown in Wiring diagrams.

7. Connect a DC power supply.

8. Check GSM signal strength according to light indication.

Note: Sufficient GSM signal strength is level 5 (five yellow flashes of indicator

Network). If GSM signal strength is not sufficient, use other antenna type.

9. Check if the module sends messages according to its configuration.

Note: The message must be sent and received at the specified IP address site. If

messages are sent to a mobile phone, check if all messages are received.

GSM communicator G10T v.2

Wiring diagram

Setting of operating parameters

Communicator G10T operating parameters are set with computer program G10config. The program can be found in website

www.trikdis.lt.

1. Connect the communicator G10T with a computer using a USB cable.

a. Download the USB driver file USB_COM.inf for MS Windows OS from the website www.trikdis.lt.

b. If the module is connected to a computer for the first time, MS Windows OS should open the window Found New

Hardware Wizard for installing USB drivers.

c. In the wizard window select the function Yes, this time only and press the button Next.

d. When the window Please choose your search and installation options opens, press the button Browse and select

the place where the file USB_COM.inf was saved.

e. Follow the remaining wizard instructions to finish the USB driver installation.

2. Start the program G10config.

3. Select the program directory Settings.

a) In the drop-down list Port select the port to which the

module is connected.

Note: specific port to which the device is connected will

appear only when the device is properly connected.

b) In the drop-down list Language select the desired

program language.

1. Press the button Connect/Disconnect [F2/F8].

Note: When the module G10T is connected to a computer,

module LED Power indicator should flash green and yellow in

turn. Program G10config status bar should indicate

connection status Connected and display the following

information about the connected module:

Module type

Device IMEI number

Module serial number

Firmware version installed in the module

4. Press the button Read [F7].

GSM communicator G10T v.2

a) When the window Access code opens, enter the access

code (default access code is 1234) and press the button

OK.

Note: If you want for the program to remember your access

code, check the box Remember. Then the Access code

window will not open when connecting to the module for the

next time.

5. Select the program directory Main and set the following parameters:

Object ID

G10T transfers messages of security control panel containing its ID number set in. Here is

the section for setting ID number (0001-FFFF) for G10T in case to identify to which object

belong messages generated by particular G10T. Set 4 symbol value;

SIM Card PIN code

Section for entering the SIM card PIN code. Leave this field by default if PIN code request is

disabled;

User code

Section for entering a user code. When connected using a User code, only those module

parameters can be changed, which change were allowed by the administrator;

Admin code

Section for entering an administrator code. When connected using an Admin code, all

module parameters can be changed and also access to parameter change can be restricted

for persons connecting with the User code.

Panel type

Option INTERFACE DTMF means that the module is applied to receive information coded in

Contact ID format from the telephone communicator of the security control panel in DTMF

codes;

IN1

If here were selected the option 24 zone in the drop-down list then after braking of input

IN1 external circuit, the module will transmit a message about this event with a code set in

the table Module events.

If here were selected the option Backup mode then module G10T will start transmitting

messages of security control panel after breaking input IN1 external circuit only;

PGM

If the option Remote control SMS is selected in the drop-down list, the module will change

its output state after receiving an SMS message containing a control command (See chapter

Remote output state control). If the option Lost Primary channel is selected, output state

will change to the opposite after losing communication through the primary channel. When

the option Lost Secondary channel is selected, output state will change to the opposite after

losing communication through the backup channel. If the option Lost Both channels is

selected, output state will change to the opposite after losing communication through the

primary and backup channels;

GPRS PING time

Time interval according to which the module will send signals PING for polling GPRS

connection;

CSD PING time

The function is disabled;

GSM communicator G10T v.2

SMS PING time

Time interval according to which the module will send signals PING for polling SMS

communication;

Test time

Time interval according to which the module will send messages Test.

6. The directory GPRS. Enter the parameters are needed for reporting to an alarm receiving centre (ARC):

Primary reporting

Select the primary communication channel in the list, through which the module will

transmit messages to ARC.

If GPRS is selected, enter the IP address or domain name and the port number of ARC in the

corresponding boxes Server IP1 address or Domain and Port;

If DTMF is selected, enter the telephone number of ARC Tel.1, to which messages will be

sent through GSM connection in DTMF tones. The telephone number should be entered

with international country code but without the “+” (plus) sign.

If SMS is selected, enter the telephone number of ARC Tel.1, to which SMS messages will be

sent. The telephone number should be entered with international country code but without

the “+” (plus) sign.

If Protegus is selected, all needed fields in section Primary reporting are filled in

automatically, Backup reporting is disabled.

ǃ Write down IMEI code from status bar, because you will need it in Protegus service

registration. How to connect G10 to Protegus see Protegus service.

Backup reporting

Drop-down list for setting the backup communication channel, through which the module

will transmit messages, when connection through the primary communication channel is

lost.

If GPRS is selected, enter the second server IP address or domain name and the port number

of ARC server to the corresponding boxes Server IP2 address or Domain and Port.

If DTMF or SMS is selected, enter the telephone number of ARC Tel.2, to which messages

will be sent through GSM connection in DTMF tones or SMS messages. The telephone

number should be entered with international country code but without the “+” (plus) sign.

Second backup reporting tel

Telephone number of ARC’s receiver, to which SMS messages will be sent, when the module

has lost GPRS connection with both servers. This option is allowed, when both the primary

and the backup GSM connection channels are selected as GPRS. The telephone number

should be entered with international country code but without the “+” (plus) sign.

Protocol

Drop-down list for selecting a protocol for encrypting messages;

Encryption key

Section for entering a 6-digit key for encrypting messages sent to ARC. The password must

be same as the password entered in a server program IPcom.

Return to primary after

Used if both the primary and backup GSM channels are selected for connection with ARC.

Enter in the section the duration of time for sending messages though the backup

communication channel, when connection through the primary channel has failed;

Backup reporting after

Used if both the primary and backup GSM channels are selected for connection with ARC.

Enter in the section the number of attempts to transmit information through the primary

communication channel, after which the module will connect to the backup communication

channel.

GSM communicator G10T v.2

Note: Administrator of an alarm receiving centre (ARC) should provide the IP addresses, port and telephone numbers,

encryption protocol, key and other parameters necessary for connecting with ARC.

APN

Access point name for connecting to the GSM operator’s network;

User

User name for connecting to the GSM network;

Password

Password for connecting to the GSM network;

DNS1, DNS2

We recommend leave values by the default in the sections if you don’t get other.

Note: APN, user name and password should be provided by the GSM network administrator, from which you have received

the SIM card.

Module events

Module events are described in the table below. After their occurs the module transmits

messages with codes given beside. Event code can be changed by double-clicking the cells

Contact ID event code or Contact ID restore code and by entering exact values by Contact

ID form in the newly opened window. After entering the values press the button OK.

Communicator

events

Meaning of event “E“

Meaning of event “R“

TIME

Internal clock of the module is not set

Internal clock of the module is set

TEST

Periodical module Test message

POWER

Power supply voltage is lower than 11,5 V

Power supply voltage has restored to 12,6 V

TAMPER_1

External circuit of Input IN1 has broken

External circuit of Input IN1 has restored

TAMPER_2

External circuit of Input IN2 has broken

External circuit of Input IN2 has restored

7. If you need to set SMS messages for users of security system, choose the directory Text SMS reporting and enter the

parameters for SMS messages to be sent:

Telephone

Telephone numbers T1, T2, T3, T4 of the four users to which SMS messages will be sent. The telephone

numbers should be entered with international country code but without the “+” (plus) sign;

Name

Choose by which tel. number G10T must send SMS after occurring event of particular type.

Alarm/Restore

Messages will be sent when the security system is alarmed/restored (events with E/R 1XX codes);

Open/Close

Messages will be sent about the arming/disarming of the security system (events with E/R 4XX codes);

Troubles

Messages will be sent about the troubles(restores) in system operation (events with E/R 3XX codes);

Tests

System test messages will be sent (events with E 6XX codes).

SMS encoding

Choose in the list drop-down the preferred encoding for the text in SMS messages;

Send SMS

When All is chosen, all messages received from the security control panel will be sent to users. When

Described Only is chosen, SMS messages will be sent only about the events in described zones;

Object ID

Enter the object name. It will be included in the message sent to user;

GSM communicator G10T v.2

Users

Entries in the table are associated with user codes, with which the security system is armed/disarmed.

When a user arms/disarms the security system with his code, his name entered in the table will be

included in the SMS message;

Zones

Entries in the table are associated with events in protected zones. When zone is alarmed/restored, its

name entered in the table will be included in the SMS message;

Partitions

If the security system is divided into several individually protected areas, entries in the table are

associated with these areas. If a zone is alarmed/restored in an area, the name of the partition entered

in the table will be included in the SMS message;

Save [F5]

By pressing this button values entered to the program G10config can be saved in the computer. A new

file with extension .gst will be created. It can be used later as a template for configuring other modules.

Restore [F11]

Button for restoring default (factory) operating parameters of the module G10T. Press the button Yes

when request window opens.

8. Press the button Write [F6] and values entered in the program G10config windows will be uploaded to the module

G10T.

9. Press the button Disconnect [F8] and unplug the USB cable from the USB socket.

Protegus service

Protegus service allows users to remotely monitor and control the communicator.

After communicator G10 is set to work with Protegus service and connected to power supply, you can set that G10

communicator would use open collector output (PGM). The user can trigger the output to activate an input on the host panel to

trigger a key-switch zone and arm/disarm the system.

To set PGM for ARM/DISARM system in Protegus application follow these steps:

1. If you do not have Protegus service account you can create it by fill registration form here: www.protegus.eu.

2. To add the system to the Protegus, press “Add new system +”, and enter required data, follow steps in pictures.

Updating communicator firmware version

When the manufacturer adds new features to the module G10T, firmware of the previously bought module can be updated:

b) Enter IMEI (from G10config status bar).

a) Enter system name.

G10 does not have Service code.

c) Go to Settings

tab.

d) Tick "Arm/Disarm with PGM".

e) Save the changes.

Otros manuales para G10T

Tabla de contenidos

Otros manuales de Teléfono móvil de Trikdis

Trikdis

Trikdis G09 Manual de usuario

Trikdis

Trikdis G17F Manual de usuario

Trikdis

Trikdis E14 Manual de usuario

Trikdis

Trikdis G10D Manual de usuario

Trikdis

Trikdis E10Tv2 Manual de usuario

Trikdis

Trikdis E16T Manual de usuario

Trikdis

Trikdis G17F Manual de usuario

Trikdis

Trikdis G10 Manual de usuario

Trikdis

Trikdis E10T Manual de usuario

Trikdis

Trikdis G16T Manual de usuario

Trikdis

Trikdis G16T 3 Series Manual de usuario

Trikdis

Trikdis G16T Manual de usuario

Trikdis

Trikdis G16T Manual de usuario

Trikdis

Trikdis Ethernet E16 Manual de usuario

Trikdis

Trikdis FireCom Manual de usuario

Trikdis

Trikdis G16 Manual de usuario

Trikdis

Trikdis G10 Manual de usuario

Trikdis

Trikdis GET Manual de usuario

Trikdis

Trikdis G16 Manual de usuario

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LG LM-X420QN Manual de usuario

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

LG LM-K420EMW Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario